Datasheet
Digital Fiber Sensor FX-100 SERIES
174
Selection
Guide
Fibers
FX-500
FX-100
FX-300
FX-410
FX-311
FX-301-F7/
FX-301-F
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
LIGHT
CURTAINS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
ENDOSCOPE
LASER
MARKERS
PLC /
TERMINALS
HUMAN
MACHINE
INTERFACES
ENERGY
CONSUMPTION
VISUALIZATION
COMPONENTS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
The code setting function makes it possible to set the
output operation, timer operation, amount of light emitted,
frequency of light emitted, ECO setting, external input,
and amount of shift by selecting a code of one’s choice.
While in the RUN Mode, pressing and holding both
the ON key (
) and OFF key ( ) simultaneously for 4
seconds will switch to the code setting function.
The quick setting function makes it possible to set
the content of the SET Mode (output operation, timer
operation, amount of light emitted, and frequency of light
emitted) simply by selecting a setting number.
While in the RUN Mode, pressing and holding both
the ON key (
) and OFF key ( ) simultaneously for 2
seconds will switch to the quick setting function.
No.
Output operation
Timer
Emission amount setting
D-ON non Level 3 (OFF)
D-ON non Level 2 (ON)
D-ON ofd 10 ms Level 3 (OFF)
D-ON ofd 10 ms Level 2 (ON)
D-ON ofd 40 ms Level 3 (OFF)
D-ON ofd 40 ms Level 2 (ON)
D-ON ond 10 ms Level 3 (OFF)
D-ON ond 10 ms Level 2 (ON)
D-ON ond 40 ms Level 3 (OFF)
D-ON ond 40 ms Level 2 (ON)
L-ON ond 40 ms Level 2 (ON)
L-ON ond 40 ms Level 3 (OFF)
L-ON ond 10 ms Level 2 (ON)
L-ON ond 10 ms Level 3 (OFF)
L-ON ofd 40 ms Level 2 (ON)
L-ON ofd 40 ms Level 3 (OFF)
L-ON ofd 10 ms Level 2 (ON)
L-ON ofd 10 ms Level 3 (OFF)
L-ON non Level 2 (ON)
L-ON non Level 3 (OFF)
Do not use during the initial transient time (0.5 sec.) after
the power supply is switched on.
Never disassemble or modify this product.
EEPROM is adopted to this product. It is not possible to
conduct teaching 100 thousand times or more, because
of the EEPROM’s lifetime.
Take care that the product is not directly exposed
frequency lighting device or sunlight etc., as it may affect
the sensing performance.
This product is suitable for indoor use only.
Avoid dust, dirt, and steam.
Take care that the product does not come in contact with
oil, grease, organic solvents, such as thinner, etc., strong
acid or alkaline.
This product cannot be used in an environment
PRECAUTIONS FOR PROPER USE
Notes: 1) When the present setting is out of the code setting range, “ ” is shown.
When “
” is selected, the set content of the digit is not changed.
2) The factory setting is “
”.
Refer to General precautions, and to the “Operation Guide” on our
Code
1st digit 2nd digit 3rd digit
4th digit
Output
operation
Timer
(Note 1)
Emission
amount
setting
Emission
frequency
ECO
External
input
Shift
(Note 1)
FX-101
FX-102
D-ON
non
Level 3
(OFF)
01
OFF
Emission
halt
ond 10 ms
12
Limit
ond 40 ms
23
Limit
ofd 10 ms
34
Full-auto
teaching
ofd 40 ms
Level 2
(ON)
01
ECO
L-ON
non
12
ON
Emission
halt
ond 10 ms
23
Limit
ond 40 ms
34
Limit
ofd 10 ms
Level 1
01
Full-auto
teaching
ofd 40 ms
12
ECO
23
OFF
2-point
teaching
34
Incident light
intensity test
Auto
01
ON
2-point
teaching
12
Incident light
intensity test
23
34
03/01/2012