USER'S MANUAL Compact Laser Displacement Sensor HL-G1 Series (Console-dedicated Version) ME-HLG1DP(00) No.
HL-G1 Series User’s Manual (Console-dedicated Version) Introduction Thank you for downloading the "Screen Data for GT-series Programmable Display for the HL-G1-series Compact Laser Displacement Sensor." Read this manual carefully and be sure you understand the information provided before attempting to install and operate the product so that the product will fully demonstrate its superior performance. Refer to the website of Panasonic Electric Works SUNX Co., Ltd. (http://panasonic-electric-works.
HL-G1 Series User’s Manual (Console-dedicated Version) Table of Contents Introduction .......................................................................................................... 0 Table of Contents.................................................................................................................1 1. Introduction of HL-G1 Dedicated Console ........................................................ 2 1-1 Applicable Programmable Display Models ......................................
HL-G1 Series User’s Manual (Console-dedicated Version) 1. Introduction of HL-G1 Dedicated Console 1-1 Applicable Programmable Display Models Panasonic Electric Works SUNX's GT-series Programmable Display (any of the following models sold separately) can be used as a dedicated console by connecting the Programmable Display to the high-functional model (HL-G1□□-S-J) of the HL-G1 Compact Laser Displacement Sensor and writing dedicated screen data to the Programmable Display.
HL-G1 Series User’s Manual (Console-dedicated Version) 1-2 Steps to Introduce Dedicated Console This section provides brief information on the introduction of the GT Series as a dedicated console. For the procedure in detail, refer to "3. Acquiring and Writing Screen Data”. ● Preparation • PC connected to the Internet * For the operating environment of the PC, refer to "GT-series User's Manual" (p. 1-9).
HL-G1 Series User’s Manual (Console-dedicated Version) 2. Nomenclature GT02 Series Side view Front view Side view Rear view COM. Port Battery cover Operation mode setting switch Battery holder USB connector (mini B) Operation mode setting switch Function SW No.
HL-G1 Series User’s Manual (Console-dedicated Version) 3. Acquiring and Writing Screen Data 3-1 Use Condition PEWJSX(E_Software_LicenseB)101001 Software License Agreement Panasonic Electric Works SUNX Co., Ltd. (“PEWJSX”) grants to you a license to use this Software on condition that you accept this Agreement. You must read this Agreement carefully before using this Software. Only in case that you accept this Agreement, you may start your use of this Software.
HL-G1 Series User’s Manual (Console-dedicated Version) Article 4 Term 4-1. This Agreement shall come into effect upon your unsealing the package of this Software, or your downloading, installing or launching the Software or likes. 4-2. PEWJSX may terminate this Agreement immediately, if you breach any of the provisions of this Agreement. 4-3. You shall, at your own costs, return, delete or destroy this Software and any of its copies within four (4) weeks after termination of this Agreement.
HL-G1 Series User’s Manual (Console-dedicated Version) 3-2 Downloading Dedicated Software Download the applicable data file of dedicated software according to the communications method (RS-422 or RS-485) and the GT-series model to be used. The following data files are available.
HL-G1 Series User’s Manual (Console-dedicated Version) 3-3 Installing USB Driver 1 Connect a DC power supply to the GT, and connect the PC and GT over USB cable. 2 The PC will automatically recognize the USB driver, and a new hardware detection wizard will be displayed. 3 Select "Install from a list or specific location" and click "Next”. 4 Click "Browse" and specify the destination of the USB driver downloaded and uncompressed. 5 The installation of the driver starts.
HL-G1 Series User’s Manual (Console-dedicated Version) 3-4 Writing Screen Data 1 Click the "GTDownLoader.exe" in the folder where the file has been expanded. 2 The message "Execute Download?" will be displayed in the prompt screen for the screen data. Click the "OK" button. 3 A progress screen will be displayed. Wait until the transfer of the data is completed. 4 Click the "OK" button on completion of data transfer. 5 End.
HL-G1 Series User’s Manual (Console-dedicated Version) 4. Sensor Connections and Initial Settings 4-1 Mounting Console For the installation of the GT Series in detail, refer to "Chapter 3 Installation and Wiring" of the "GT-series User's Manual”. Use the four mounting brackets and four mounting screws provided and mount the console to the mounting plate. GT02 Series (1) Insert the unit into the mounting plate. (2) Attach the mounting brackets to the grooves of the unit, and slide and fix the brackets.
HL-G1 Series User’s Manual (Console-dedicated Version) 4-2 Connecting Dedicated Console to HL-G1 For general handling information on the GT Series, refer to the GT-series User’s Manual. ● Connecting GT02 Series to HL-G1 (Single HL-G1 Unit over RS-422) • Make one-to-one wiring for each signal name between the HL-G1 and console connected through a cable.
HL-G1 Series User’s Manual (Console-dedicated Version) ● Connecting GT12 Series to HL-G1 (More than a single HL-G1 unit over RS-485) • Up to four HL-G1 units can be connected. • The console will be the terminator. Connect the ground terminal "E" to the signal "-RD”. • Set the “Terminating resistor selection” for the terminating HL-G1 unit only, while turn OFF the terminating resistor for each intermediate HL-G1 unit connected through a bus line.
HL-G1 Series User’s Manual (Console-dedicated Version) 4-3 HL-G1 Settings Before using the compact console (GT-series unit) for communication with the HL-G1, select and set communications conditions on the HL-G1 side according to the communications specifications. ● HL-G1 Settings for communications conditions COM Settings Item RS-422 (single-unit connections only) Terminating resistor R3 (see note 1) selection Sensor No.
HL-G1 Series User’s Manual (Console-dedicated Version) 4-4 Changing and Saving Display Language of Console The console screen will display in English when the console is started with the sensor head connected after screen data is written. Environment settings for the console are required to change the displayed language on the screen. The settings are saved in the sensor. Execute the Save command after making the settings.
HL-G1 Series User’s Manual (Console-dedicated Version) 5. Screen Configuration and Basic Operation 5-1 Top Menu Screen and Basic Buttons ● Top menu GT12 top menu GT02 top menu ÌThe top menu screen shows the above items. The user can move to other screens through here. Meas Display Used to display the measurement value of the sensor connected. Meas Operate Used to operate the measurement control of the sensor connected. (GT02 only) Sensor Setting Used to make various sensor settings.
HL-G1 Series User’s Manual (Console-dedicated Version) 5-2 Basic Console Operation Moving between Setting Screens The operation screen is of hierarchic structure. ) to go to the target screen and make Touch the Up and Down Keys ( necessary settings. ····· The value of each item in the sensor setting menus (Pro1 through Pro7) will increase by 1. ····· The value of each item in the sensor setting menus (Pro 1 through Pro7) will decrease by 1.
HL-G1 Series User’s Manual (Console-dedicated Version) Selection This section provides information on how to select the target item from multiple choices. [Selection from a few choices] The selectable item changes as shown each time the key is touched. Emission Emis sion STOP [Selection from many choices] The selectable item changes as shown each time the Up Key ( ) is touched. 1 4 16 Press the Down Key ( selection.
HL-G1 Series User’s Manual (Console-dedicated Version) Numeric Input Set value This section provides information on how to input numeric values, such as limit values and offset values. The keyboard will be displayed for items for which numeric input is possible. 1 Touch the frame above the set value. The system is ready to accept numeric input, and the cursor starts flashing. 2 Enter the integer part from the keyboard. 3 Touch the decimal ( ) on the keyboard.
HL-G1 Series User’s Manual (Console-dedicated Version) 5-3 Console-dedicated Functions Output setting menu (GT-12 setting screen) ● Display console measurement value Use this function to fix the console measurement value after the decimal point to 0. Set this item to disable the change in the display of the minute measurement value of the console. Set value: FULL, Set 1, Set 2, and Set 3 [FULL] The full value down to the fourth decimal place is displayed. [Set 1] The fourth decimal point is fixed to 0.
HL-G1 Series User’s Manual (Console-dedicated Version) ● Panel lock Use this function to prevent set value changes with console key manipulation. It is possible to move between screens. Set value: ON, OFF ● Touch beep Use this function to enable or disable the touch beep. Set value: ON, OFF ● Language Use this function to select the display language.
HL-G1 Series User’s Manual (Console-dedicated Version) 6. Screen Transition Charts This section provides screen transition charts of the console dedicated to HL-G1. For details of each function, refer to the HL-G1 User's Manual provided with the sensor head.
HL-G1 Series User’s Manual (Console-dedicated Version) ● Setting item screen for each setting menu (for GT02 use) Pro1: Sensing setting menu Pro2: Data processing menu Pro3: Output setting menu Sampling cycle Average times Judgment output selection Shutter time Analysis mode Displacement judgment (Threshold a) Span Displacement judgment (Threshold b) Offset Hysteresis Judgment output OFF delay Panel measurement value display Console measurement value display 22
HL-G1 Series User’s Manual (Console-dedicated Version) Pro4: Analog setting menu Pro5: Alarm setting menu Pro7: System setting menu Analog output selection Analog output at alarm Timing mode Analog scaling (current) Digital output at alarm Laser control Analog scaling (voltage) Alarm delay times Eco mode Initialization Environment setting menu Save Console settings (1/2) Console settings (2/2) Type No.
HL-G1 Series User’s Manual (Console-dedicated Version) 6-2 GT12 Screen Transition ● Transition from top screen to each menu screen Top screen Environment setting menu Sensor setting menu Measurement value display [ALL] Sensor setting menu [NO. 1] Memory change Pro1 Sensing setting Measurement value display menu Pro2 Data processing setting Pro3 Output settings No. 1 display Pro4 Analog settings No.
HL-G1 Series User’s Manual (Console-dedicated Version) ● Setting item screen for each setting menu (for GT12 use) Pro1: Sensing setting menu Pro2: Data processing menu Pro3: Output setting menu Sampling cycle Average times Judgment output selection Shutter time Analysis mode Displacement judgment (Threshold a) Span Displacement judgment (Threshold b) Offset Hysteresis Judgment output OFF delay Panel measurement value display Console measurement value display 25
HL-G1 Series User’s Manual (Console-dedicated Version) Pro4: Analog setting menu Pro5: Alarm setting menu Pro7: System setting menu Analog output selection Analog output at alarm Timing mode Analog scaling (current) Digital output at alarm Laser control Analog scaling (voltage) Alarm delay times Eco mode Initialization Environment setting menu Save No. of units connected Console settings Type No.
HL-G1 Series User’s Manual (Console-dedicated Version) MEMO 27
HL-G1 Series User’s Manual (Console-dedicated Version) Revision history Released date Revision No.
October 2010
