Operating Instructions Dual Camera HX-WA10 Model No. Before use, please read these instructions completely. Model number suffix “EB” denotes UK model. EB Web Site: http://www.panasonic-europe.
Information for Your Safety Dear Customer, We would like to take this opportunity to thank you for purchasing this Panasonic Dual Camera. Please read these Operating Instructions carefully and keep them handy for future reference. Please note that the actual controls and components, menu items, etc. of your Dual Camera may look somewhat different from those shown in the illustrations in these Operating Instructions.
k Concerning the battery Warning Risk of fire, explosion and burns. Do not disassemble, heat above 60 oC or incinerate. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. k EMC Electric and magnetic compatibility This symbol (CE) is located on the rating plate.
For business users in the European Union If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information. [Information on Disposal in other Countries outside the European Union] These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.
IMPORTANT! PLEASE READ k About handling the camera i Opening and closing the battery cover or terminal cover in a sandy or dusty environment may cause water to get inside the camera and result in malfunction, so be especially careful in these environments. i Do not touch the lens or terminals with dirty hands. i Do not open or close the battery cover or terminal cover near or in water, or with wet hands.
k Be sure to take some test pictures beforehand Before those important events, be sure to take some trial pictures to confirm that the images and audio are being properly recorded. k Indemnity about recorded content Panasonic does not accept any responsibility for damages directly or indirectly due to any type of problems that result in loss of recording or edited content, and does not guarantee any content if recording or editing does not work properly.
k Concerning this unit’s recording method and compatibility
IMPORTANT: ABOUT THE WATERPROOF PERFORMANCE OF THE CAMERA i This camera is qualified JIS protection grade 8 (JIS IPX8) for waterproof performance. It is waterproof up to a depth of 3 meters for at least 60 minutes.* i The supplied accessories are not waterproof (excluding handstrap). * This means that the camera can be used underwater for a specified time in a specified pressure in accordance with the handling method established by Panasonic.
MAINTENANCE AND WATERPROOF PERFORMANCE k Before using the camera in water, please check the following Do not open or close any of the covers in sandy or dusty environments, near the waterside, or with wet hands. Sand or dust adhering to the camera can result in water getting inside. j Check that there is no foreign matter adhering to the inside of any of the covers. h If lint, hair, sand or the like is present, water may leak into the camera in seconds and damage it.
k To prevent water leaking into the camera, please observe the following precautions before using it. k Check that there is sufficient battery power and card memory remaining. k Do not open or close the battery cover or terminal cover in places with sand and dust, or with wet hands. k At the time of purchase, the battery cover lock is in the locked position. When opening the battery cover, first release the lock.
2 If there is foreign matter adhering to the camera, use the supplied brush to remove it. h If there is any foreign matter, such as lint, hair, sand, etc., on the parts indicated by the text balloons in the illustration, water will leak inside within seconds and may damage the Brush (supplied) camera.
i If there is liquid on the surface, wipe it off with a soft dry cloth. i The integrity of the rubber seals decreases after about 1 year. It is strongly recommended that you have the seals replaced (subject to a fee) at least once a year at the store where the camera was purchased or at nearby service centre. 3 1 With the battery cover lock released, press the battery cover to close it.
HINT i If there is any foreign matter on the camera, use the supplied brush to remove it. i If the camera is used in the following environments, foreign matter such as sand or dust may inadvertently get caught in the gap between the battery cover or terminal cover and the body. h In the sea or in waters in which sand is suspended. h In places with a lot of sand or dust, such as at the beach or in a sandbox.
k Causes of water leak i If the camera is used in any of the following conditions, a gap may appear between the camera body and the battery cover or terminal cover, resulting in water seeping in and causing the camera malfunction. Water can leak inside through the gap Battery cover Rubber seal Where the rubber seal contacts the camera body Terminal cover Rubber seal Where the rubber seal contacts the camera body h When there is foreign matter, such as lint, hair, sand, etc.
2 3 4 Wipe off the water, place the camera on a dry cloth and leave it to dry for a while in a well-ventilated shaded spot. Check that there is no water on the camera, and open the battery cover and terminal cover. h Moisture may easily accumulate in the grooves inside the covers, so take care that no water gets inside. Wipe off any water or sand inside the battery cover and terminal cover with the supplied brush or a soft dry cloth.
k About the water draining design This camera is designed so that water that entered the gaps around the zoom switch etc. drains out. For this reason, bubbles may appear when the camera is immersed in water, but this is not a malfunction. i Drainage holes are found at two points on the bottom of the camera. Hold the camera vertically, as shown, to drain off the water.
WHAT YOU CAN DO WITH YOUR DIGITAL MOVIE CAMERA Easy shooting/playback (Basic features) Intelligent Auto Mode ... (page 56) 16M-S 353 1080-30p 000:15:53 Just point the camera at the subject, and it automatically ascertains the scene and captures the images with the optimum settings. Shoot movies ... (page 61) 2M Take photos ... (page 62) 16M-S 1080-30p 000:00:09 F3.5 1/30 Play back videos and photos ... (page 69) 20.12 2011 20.12.
Using the convenient features (Practical applications) Image stabiliser... (pages 51, 84) Subject tracking... (pages 53, 90) Scene mode...
Keeping recorded videos (Copy/dubbing) From built-in memory to SD card... (page 55) DVD recorder and video deck... (page 164) * It is not possible to directly insert in the card slot an SD card recorded with this camera and play back or dub from it. * It is not possible to connect the camera to the USB connector and play back or dub from it. * Recording with HD image quality on a Blu-ray disc recorder is not possible. On a computer...
CONTENTS Information for Your Safety .................................................................... 2 CHECKING THE INCLUDED ACCESSORIES .................................... 24 ABOUT THE CARD ............................................................................. 25 Media cards that can be used with this camera (as of February 2011) ............................................................... 25 SETUP PARTS NAMES ..............................................................................
PLAYBACK PLAYING BACK VIDEOS AND PHOTOS ............................................69 How to save one frame from a video as a photo ...........................72 DELETING FILES .................................................................................73 Delete single/delete all/delete folder .............................................73 Delete selected ..............................................................................74 PLAYBACK MODES ...................................................
OPTION SETTINGS DISPLAY THE OPTION SETTING MENU ......................................... 113 INTRODUCTION TO THE OPTION SETTING MENU ...................... 114 TV output setting (page 117) ...................................................... 120 Storage folder setting (page 119) ............................................... 124 Playback folder setting (page 119) ............................................. 125 File No. continued setting (page 119) .........................................
CONNECTING TO A TV CONNECTING TO A TV .....................................................................159 Connecting to a video input terminal ...........................................160 Connecting to the HDMI terminal ................................................160 PLAYING BACK ON A TV ..................................................................161 Playback using VIERA Link™ (HDAVI Control™) .......................161 COPYING/DUBBING COPYING/DUBBING .......................................
CHECKING THE INCLUDED ACCESSORIES Check the accessories before using this unit. Product numbers correct as of February, 2011. These may be subject to change. Battery pack VW-VBX070 AC adaptor VSK0752 USB cable VFA0544 AV cable VFA0543 Brush VYC1064 CD-ROM Software Handstrap *To prevent the camera from dropping, be sure to attach the handstrap (page 60). VFC4703 i Please dispose of packing materials properly. i Keep the battery pack and the brush out of reach of children to prevent swallowing.
ABOUT THE CARD Media cards that can be used with this camera (as of February 2011) Use SD cards conforming to Class 4 or higher of the SD Speed Class Rating* for video recording. This camera is compatible with SDXC devices (SD Memory Card/SDHC Memory Card/SDXC Memory Card compatible devices). If using an SDHC memory card/SDXC memory card in different device, please confirm that it is compatible with the respective memory card.
i 4 GB or more Memory Cards that do not have the SDHC logo or 48 GB or more Memory Cards that do not have the SDXC logo are not based on SD Memory Card specifications. i Cards with capacity larger than 64 GB cannot be used. i When the write-protect switch on the SD card is locked, no recording, deletion or editing will be possible on the card. i Keep the Memory Card out of reach of children to prevent swallowing.
SETUP SETUP PARTS NAMES SETUP Front Speaker Lens Monitor unit Internal Stereo microphone Flash i The flash unit becomes very hot and may cause a burn. Avoid touching the flash unit when shooting. * The tripod mounting hole is on the bottom. Attaching to a tripod having a screw length longer than 5.5 mm may damage the camera.
Rear SETUP [ ] button Photo shooting button [@] button Video recording button Zoom switch button During recording: Zoom photography [W/T] (page 65) During playback: Volume adjustment (page 70 and page 80) Image magnification (page 77) Playback display switching (page 76) LCD monitor Status indicator Terminal cover Terminal cover lock USB/AV terminal Battery cover HDMI terminal Strap holder (page 60) 28 VQT3P45
k About the status indicator (See page 182 regarding the charging status.) i The status indicator lights or flashes to show the camera’s operating status.
CHARGING THE BATTERY PACK SETUP At the time of purchase, the battery pack is not charged. Please charge it fully before using it. It has been found that counterfeit battery packs which look very similar to the genuine product are made available to purchase in some markets. Some of these battery packs are not adequately equipped with protective devices to meet the requirements of appropriate safety standards. There is a possibility that these battery packs may lead to fire or explosion.
Approximate operating time and number of recordable images Number of recordable images Recording time Playback time Approx. 170 images By CIPA standard Approx. 85 min Approx. 180 min Recording conditions by CIPA standard i CIPA is an abbreviation of Camera & Imaging Products Association. i Using the supplied battery i Using a Panasonic SD Memory Card (2 GB) VQT3P45 31 SETUP i These times are approximations. i The indicated charging time is for when the battery has been discharged completely.
1 Open the battery cover. Battery cover lock SETUP 2 Open Battery cover 1 Push the battery cover lock to the right to release it.
2 Battery pack Connector markings 4 Close and slide shut 3 Insert the battery pack while matching the connector markings. Coloured label 5 Push the battery cover lock to the left to lock it. The coloured label is visible when the battery cover lock is not completely closed. Be sure to close the lock completely so that the coloured label is not visible. VQT3P45 33 SETUP Insert the battery pack, then replace the battery cover.
3 Use the USB cable (supplied) to connect the camera and the AC adaptor, and then connect the AC adaptor to a power outlet. SETUP h Use only the supplied USB cable. Operation is not guaranteed if a different USB cable is used. h The AC adaptor is for this camera only. Do not use it with other devices. h Recharging takes place only when the camera is turned off or is in the sleep mode (page 40). Recharging does not take place when the camera is in the recording mode or playback mode.
VQT3P45 35 SETUP HINT After installing the battery and/or after charging the battery, close the battery cover and terminal cover securely i If any cover is not closed or is not closed completely, the camera will no longer be waterproof. When closing a cover, close it securely while making sure that no foreign object such as sand, hair, dust, etc. is caught in the rubber seal.
About the temperature alert icon SETUP During camera use, if the temperature of the battery or inside the camera (excluding the battery) rises, a temperature alert icon will appear as described below. k When the battery or internal camera (excluding battery) temperature rises during use h During camera use, if the temperature of the battery or inside the camera (excluding the battery) rises, a icon lights on the LCD monitor.
INSTALLING THE CARD 4 Insert the battery pack (page 33), then close Battery cover lock 2 Open Battery cover 1 Push the battery cover lock to the right to release it. 3 With the label side facing up, push the card straight in until you hear a click. h To remove the card, press it in, and then release. The card will protrude slightly, and you can then pull it out. 1 Push the middle part of the card. 5 Push the battery cover lock to the left to lock it.
SETUP HINT Close the battery cover securely i If the battery cover is not closed or is not closed completely, the camera will no longer be waterproof. When closing the battery cover, close it securely while making sure that no foreign object such as sand, hair, dust, etc. is caught in the rubber seal. i If there is moisture inside the battery cover or terminal cover, after wiping the moisture from all surfaces, use the supplied brush to remove any foreign matter.
TURNING THE CAMERA ON AND OFF SETUP Turning on the camera 1 Open the monitor unit, and press the power button. h The LCD monitor turns on.
Turning off the camera SETUP 1 Press the power button for at least 1 second. h The camera turns off. h If you briefly press the power button, once, the camera will switch to the sleep mode. Turning on the camera when it is in the sleep mode In order to preserve battery pack power, the ECONOMY function operates to automatically turn off the camera (sleep mode) after about 5 minutes of no use during shooting, or about 5 minutes of no use during playback (factorypreset settings).
DATE AND TIME SETTING Example: To set the clock to 19:30 on 20 December 2011 1 2 3 Turn on the camera (page 39), and display Option Setting Menu 1 (page 113). Select [CLOCK SET] and press the SET button. h The Clock Set Screen appears. h Follow the procedures below to enable or disable the date display during playback, to set the display format for the date, and to set the date and time. Set the date. 1 Select [DATE]. 2 Press the SET button. h The Set Date Screen appears. 3 Set the date to “20/12/2011”.
4 SETUP 5 6 42 Set the clock. 1 Select [TIME]. 2 Press the SET button. h The Set Time Screen appears. 3 Set the time to “19:30”. h The time is set in the following order: Set the hour → Set the minute. 4 Press the SET button. Set the order in which the date is displayed during playback. 1 Select [DISP]. 2 Press the SET button. h The Set Date Format Screen appears. 3 Press [I] or [J]. h The order of the date display changes. 4 Press the SET button.
Date and time backup Under normal conditions, while the battery pack is being replaced, an internal battery will maintain the date and time settings. However, there is a small chance the settings may be lost (the backup will last for about 7 days). It is recommended to check that the date and time settings are still correct after replacing the battery pack and before shooting or recording of any type.
SETUP SWITCHING BETWEEN THE RECORDING MODE AND PLAYBACK MODE Switch between the recording mode (for recording) and the playback mode (for viewing your recorded images). 1 2 Turn on the camera (page 39). Press the REC/ button. h The mode changes. h The mode changes each time the REC/ REC/ 44 VQT3P45 button button is pressed.
MENU SCREEN SETUP Accessing/exiting the Menu Screen 1 2 Set the camera to the recording or playback mode (page 44). Press the MENU button. h The Menu Screen appears. h To cancel the Menu Screen, press the MENU button again. Tab RECORDING MENU 1 1 REC MODE 2 PICTURE SIZE 3 1 2 3 SCENE MODE COLOUR MODE FLASH SELF TIMER SET ENTER 1080-30p 16M-S Option tab k To display a different Tab Menu h The Menu Screen consists of the Tabs Menu (tabs 1, 2 and 3) and the Option Tabs Menu (tabs 1, 2 and 3).
Using the Menu SETUP 1 2 Display the desired menu (page 45). Press [I] or [J] to select the item you wish to change, and press the SET button. h The Setting Screen for the selected item appears. h To return to the Menu Screen, press the MENU button.
VQT3P45 47 SETUP HINT About the applicable mode indicator i This indicator shows the shooting mode(s) for which the selected setting is effective. i O@: This setting is effective during photo shooting. i O@: This setting is effective during video recording. i O@: This setting is effective during photo shooting and video recording.
Overview of the Menu Screen SETUP Recording Menu RECORDING MENU 1 1 REC MODE 2 PICTURE SIZE 3 1 2 3 SCENE MODE COLOUR MODE FLASH SELF TIMER ENTER 1 Recording mode (page 78) : Record at 1920 × 1080 pixels (60i). : Record at 1920 × 1080 pixels (30p). : Record at 1280 × 720 pixels (60p). : Record at 1280 × 720 pixels (30p). : Record at 960 × 540 pixels (30p). : Record at 640 × 480 pixels (30p). <: Make an audio recording.
× 3456-pixel C: 4608 hi-speed burst. 3 Scene mode (page 82) : Scene mode is deactivated. : Shoot fast-moving subjects with less blur. : Blur the background to accentuate the subject in the foreground. : Record a clear image of a subject illuminated by spotlight. : Natural looking images in bright surroundings, such as in a ski area. : Vivid blue for sea and sky, subjects do not appear dark even in bright sunlight. : Capture the vibrant reds in sunrise and sunset shots.
SETUP 1 RECORDING MENU 2 2 3 1 2 3 50 VQT3P45 E.I.S.
2 Focus (page 85) h Adjust the focus according to the distance to the subject. *: The camera automatically focuses on the subject with a range of 10 cm to ∞ (normal). -: The focus can be set manually. : The camera focuses on the subject within a range of 1 cm to ∞ (macro). 3 Focus mode : 9-point range finder focus : Spot focus A focus mark ' appears in the centre of the LCD monitor.
SETUP 1 RECORDING MENU 3 2 EXPOSURE 3 1 2 3 52 SUBJECT TRACKING DIGITAL ZOOM WIND CUT AUTO REVIEW SHORTCUTS ENTER VQT3P45 P 1 1 2 3 4 5 6 7
2 Subject tracking (page 90) h Automatically target a specific colour with the colour tracking function, or capture sharp face shots with the face tracking function. : Enable face tracking. : Enable colour tracking. : Disable face tracking and colour tracking. 5 Auto review h Specify the duration that the captured image is shown on the LCD monitor after the [O] button is pressed. : The image is shown on the LCD monitor for about 1 second after capture.
Playback Menu SETUP 1 2 1 2 3 PLAYBACK MENU 1 SLIDESHOW PLAY VOLUME PROTECT DELETE ROTATE RESIZE ENTER 1 Slideshow (page 96) h Specify the slideshow settings and play the slideshow. 2 Play volume h Adjust the volume for video and audio file playback. 3 Protect (page 97) h File protect setting (delete prohibited) 54 VQT3P45 1 2 3 4 5 6 7 4 Delete (page 73) h Delete files. 5 Rotate (page 99) h Rotate a photo.
2 1 2 3 PLAYBACK MENU 2 RED-EYE CORRECT. EDIT VIDEO COPY ENTER 1 Red-eye correction (page 100) h Repair the “red-eye” caused by the flash (photos only). 2 Edit video (page 101) h Edit videos. SETUP 1 1 2 3 4 3 Copy (page 110) h Copy files from the built-in memory to the card.
INTELLIGENT AUTO MODE SETUP The following modes (appropriate for the condition) are set just by pointing the unit to what you want to record. button Press the button once to activate the Intelligent Auto (iA) mode. i The icon appears on the LCD monitor. i Press it again to cancel the Intelligent Auto mode. button Mode 56 Scene Effect Portrait When the subject is a person Faces are detected and focused automatically, and the brightness is adjusted so it is recorded clearly.
Mode Effect Recording night scenery You can record night scenery vividly by slowing the shutter speed. *2 Macro Recording zooming in on a flower etc. This allows recording at very close proximity to the object of recording. *1 Normal Other situations Contrast is adjusted automatically for clear images. Video recording only Photo shooting only HINT i Depending on the recording conditions, the unit may not enter the desired mode.
SETUP k Intelligent Auto Mode When switching to Intelligent Auto Mode, the Auto White Balance and Auto Focus operate and automatically adjust the colour balance and focusing. Depending on the brightness of the subject etc., the aperture and shutter speed are automatically adjusted for an optimum brightness. i Colour balance and focus may not be adjusted automatically depending on light sources or scenes. If so, manually adjust these settings.
BASIC OPERATION SHOOTING BASIC OPERATION/SHOOTING BEFORE TAKING PICTURES For best results Correct hold Incorrect hold A finger is blocking the lens or flash. Example 1: Example 2: Grip the camera by Grip the camera by wrapping the fingers wrapping the of the right hand, fingers of the right from the little finger hand, from the little to the middle finger, finger to the index around the camera, finger, around the and hook the index camera. finger above the lens.
How to use the accessories k Handstrap VQT3P45 ▲ ▲ BASIC OPERATION/SHOOTING 60
VIDEO RECORDING 1 3 Press the [@] button. h Recording begins. h It is not necessary to keep the [@] button pressed while recording. h When the remaining recording time available for the currently recording video becomes 30 seconds or less, a countdown of the remaining recording time appears on the display. h When the file size of the current recording exceeds 4 GB, the file is saved once, and recording begins in a new file. (4-GB files are automatically created (page 189).) End the recording.
TAKING PHOTOS 1 BASIC OPERATION/SHOOTING Turn on the camera (page 39), and set it to the recording mode (page 44). h If the subject is a person, a green double-frame appears around the face (page 90). 2 [O] button Press the [O] button. 1 Press the [O] button halfway. h The autofocus operates, and the image is focused (focus lock). 2 Continue to gently press the [O] button all the way. h The shutter releases and the image is captured.
VQT3P45 63 BASIC OPERATION/SHOOTING HINT What is the camera focusing on? Target mark i A target mark & on the LCD monitor shows the area the camera is 16M-S focusing on. i The camera automatically determines the correct focus by measuring from 9 different focus points within the shooting area. If the target mark is at a position that is F3.5 different from the point you wish to 1/2 focus on, you can refocus, for Camera shake icon example, by changing the shooting Shutter speed angle.
Shoot a photo while recording a video You can capture a photo (single frame) while recording a video. 1 While recording a video, when you see a scene you’d like to capture a photo of, press the [O] button. BASIC OPERATION/SHOOTING HINT i When shooting a photo while recording a video, the flash does not operate. i The photo stabiliser (page 84) is inoperative.
MACRO-PHOTOGRAPHY (ZOOM) Your camera has two zoom functions: Optical zoom and Digital zoom (page 53). 1 3 BASIC OPERATION/SHOOTING 2 Point the camera lens at the subject. Zoom switch Push the zoom switch toward [T/]] or [W/P] to compose the desired image. [T/]]: Zoom in on the subject. [W/P]: Zoom out. h When the zoom switch is pushed, the zoom bar appears on the LCD monitor. Take the picture. For video recording, see page 61. For shooting photos (single), see page 62.
BASIC OPERATION/SHOOTING HINT When recording videos at a high magnification i When recording videos at a high magnification, a moving subject or moving camera can cause camera shake, resulting in a distorted playback image. This phenomenon is due to the characteristics of the MOS sensor and is not a malfunction. i It is recommended that you use a tripod to stabilise the camera when recording videos at a high magnification.
SHOOTING UNDER WATER This camera can be used underwater up to a depth of 3 m for up to 60 minutes continuously. When shooting underwater, set the scene mode setting to underwater . This setting ensures the best colours and audio recording for underwater photography (pages 49 and 82).
After using in water After using the camera in water, wash it with fresh water and dry it completely. 1 BASIC OPERATION/SHOOTING 2 3 Turn off the camera, and close the battery cover and terminal cover securely. Wash the camera with fresh water. h Fill a shallow basin with fresh water, and immerse the closed camera for about 10 minutes. Rotate the monitor unit several times to clean it completely. Dry the camera.
PLAYBACK BASIC OPERATION/PLAYBACK PLAYING BACK VIDEOS AND PHOTOS 1 3 Yellow frame Select the image to play back. h Use the arrow keys to move the yellow frame to the file you wish to play back. h The image information for the framed image is shown at the bottom of the LCD monitor. 20.12.2011 18:41 10.5MB 1080-60i SET ENTER Press the SET button. h The image you selected in step 2 is displayed on the LCD monitor. h If a video was selected, playback begins.
Video playback operation To do this... Normal forward playback Stop playback Pause Do this Press the SET button. During playback, press [J]. During playback, press the SET button or press [I]. During accelerated playback, press [I]. BASIC OPERATION/PLAYBACK To play back During forward After pausing playback, press [H]. one image playback at a time During reverse (singleAfter pausing playback, press [G]. playback frame step) During forward After pausing playback, press and hold [H].
HINT If the appears on the Playback Screen... i The icon appears when playing back a file that was saved in segments (page 190).
How to save one frame from a video as a photo 1 2 Play back the video. Pause the playback at the point you wish to “snap” a photo. BASIC OPERATION/PLAYBACK Press the [O] button. h The screen to select the aspect ratio of the photo appears. Select the desired aspect ratio, and press the SET button. Note, however, that if the video aspect ratio is 4:3, you cannot select 16:9. h The latest image number is assigned to the photo when it is saved.
DELETING FILES Deleted files cannot be restored, so delete files only after carefully checking the contents. Delete single/delete all/delete folder 2 BASIC OPERATION/PLAYBACK 1 Display the Playback Menu 1 DELETE (page 45), select the delete setting, and press the SET DELETE SINGLE button. DELETE SELECTED DELETE SINGLE: DELETE ALL Deletes one file at a time. DELETE FOLDER DELETE SELECTED: Deletes the selected files SET ENTER (page 74). DELETE ALL: Deletes all files.
3 BASIC OPERATION/PLAYBACK Select [DELETE], and press the SET button. h The currently displayed file is deleted. h To delete other files, select the files, select [DELETE] and press the SET button. h The Delete Confirmation Screen again appears. To delete the files, select [YES] and press the SET button. If [DELETE FOLDER] was selected, select [YES] again and press the SET button, and the files will be deleted. Delete selected Delete selected files.
4 6 Press the [O] button or [@] button. h The Delete Confirmation Screen appears. Select [YES], and press the SET button. h The selected files are deleted. HINT i Files that are protected from accidental delete cannot be deleted. To delete protected files, set the protect setting for the files to off (page 97), and then follow the file delete procedure. VQT3P45 75 BASIC OPERATION/PLAYBACK 5 Press the SET button. h The selected file is marked with the delete icon [>].
PLAYBACK MODES 21-image display playback BASIC OPERATION/PLAYBACK 1 2 3 Display the image you wish to play back. h The 8-image display appears. Push the zoom switch toward the [W/P] side. h The 21-image display appears. h While the 21-image display is shown, you can push the zoom switch toward the [T/]] side to change to the 8-image display, and push it again toward the [T/ ]] side to change to the singleimage display. 20.12.2011 14:25 100-0021 Select the image to play back.
Magnifying (zooming in) the image (photos only) 1 2 Display a photo. 105% SAVE SET 100% Move HINT The magnified portion of the image can be saved as a separate image i Press the [O] button. The magnified portion is saved as a new photo. i The image size of the saved photo of the magnified portion will be smaller than that of the original photo. VQT3P45 77 BASIC OPERATION/PLAYBACK Push the zoom switch toward the [T/]] side. h Magnification is enabled.
ADVANCED OPERATION SHOOTING ADVANCED OPERATION/SHOOTING RECORDING MENU 1 To access and use the Menu Screen, see page 45 to 47. Recording mode setting (page 48) ADVANCED OPERATION/SHOOTING When recording a video, smoother motion and better image clarity can be achieved by a higher pixel rate (resolution) and a faster frame rate. However, the file size will also be proportionately larger, requiring longer times to edit and store (page 55).
Audio recording and playback k Recording 1 3 Press the [@] button. h Audio recording begins. h During audio recording, < appears in the LCD monitor. h It is not necessary to continue pressing the [@] button while recording. h When the remaining recording time available for the currently recording video becomes 30 seconds or less, a countdown of the remaining recording time appears on the display.
k Audio playback 1 Select an audio file (: icon), and press the SET button. h Playback begins. To do this... Normal playback Do this Start playback Press the SET button. Pause Press the SET button. Press [I]. ADVANCED OPERATION/SHOOTING Stop playback Press [J]. Fast forward (Maximum 15×) During playback, Press [H]. Each time [H] is pressed, the speed increases. If [G] is pressed, during fast forward, the speed decreases.
Recorded pixels (page 48) For photos, you can select either the 4:3 or 16:9 horizontal to vertical aspect ratio. This menu is also used for shooting hi-speed bursts. Hi-Speed Burst 1 2 Select C or t, and press the SET button. h The menu display is cancelled if the MENU button is pressed. HINT What is the maximum number of images in a hi-speed burst sequence? C: 8 shots t: 20 shots i If you continue shooting even after the maximum number of images has been captured, recording does not stop.
When the self-timer is used... i Shooting stops automatically after the maximum number of images has been captured. About the focus when shooting hi-speed bursts i When a hi-speed burst is captured, the autofocus operates when the [O] button is pressed halfway, fixing the focus. Can the flash be used? i The flash does not operate when shooting hi-speed bursts. Scene mode setting (page 49) You can select from various preset settings (aperture, shutter speed, etc.) for specific shooting conditions.
Self-timer setting (page 49) By assigning an operation shortcut to an arrow key (page 92), you can set the self-timer from the Recording Screen. HINT To cancel the self-timer function... i If the [O] button or [@] button is pressed again before the shutter is released, the self-timer countdown is cancelled. i For video photography, recording does not stop automatically. i The self-timer is automatically reset to off N after recording is ended and the camera turned off.
RECORDING MENU 2 To access and use the Menu Screen, see page 45 to 47. Motion compensation (image stabiliser) setting (page 51) Your camera can minimize a jittery picture by compensating for unintentional hand motion. ADVANCED OPERATION/SHOOTING HINT If the motion compensation does not seem to be working... i Due to the mechanical characteristics of this function, it may not be possible for the camera to compensate for violent motion.
Focus setting (page 51) How to use the manual focus 1 2 Select -, and press the SET button. h The focus adjustment bar appears. 16M-S 340 1080-30p 000:15:17 HINT About the macro mode i When the focus range is set to macro , the zoom is temporarily set to the wide end. i By assigning an operation shortcut to an arrow key (page 92), you can change the focus setting from the Recording Screen. i In some cases it may be difficult for the auto focus to work.
ISO sensitivity setting (page 51) With the initial settings, the ISO sensitivity is automatically set according to the brightness of the subject. However, the ISO sensitivity can be set to a fixed setting. HINT i By setting a higher ISO sensitivity, you can set faster shutter speeds and capture images in darker locations, but noise in the captured images may increase or the images may be irregular.
White balance setting (page 51) This camera automatically adjusts the white balance under most lighting conditions. However, if you want to specify the lighting conditions or change the overall tone of the image, the white balance can be manually set. How to use the “white set” 1 2 Fill the entire screen with a plain white card (or piece of paper, etc.). HINT To cancel the white balance setting i Select >, and then press the SET button.
RECORDING MENU 3 To access and use the Menu Screen, see page 45 to 47. Exposure setting (page 53) The shutter speed and aperture size can be set individually. 1 ADVANCED OPERATION/SHOOTING 2 88 Select the desired icon from the exposure menu, and press the SET button. 1 If , is selected, press [I] or [J] to select aperture value F3.5 or shutter speed. 1/1000 2 Press [G] or [H] to change the setting for the selected Shutter speed parameter.
VQT3P45 89 ADVANCED OPERATION/SHOOTING HINT i To prevent the effects of camera shake at slow shutter speeds, it is recommended to use a tripod or other method to stabilise the camera. i A slow shutter speed may be useful for Taking pictures in a darker environment, but noise in the image may be increased. i If the exposure setting is set to T, g or H, by assigning an operation shortcut to an arrow key (page 92), you can select the T, g or H exposure setting from the Recording Screen.
Subject tracking settings (page 53) Adjust the settings to automatically target a specific colour with the colour tracking function, or capture sharp face shots with the face tracking function. Shooting with the face tracking function 1 Set the face tracking setting to . h When the face tracking function is activated, a double green frame appears superimposed on the face in the centre of the LCD monitor. h Each of the other faces is framed by a single green frame.
Shooting with the colour tracking function (photos only) 1 2 Move the target mark to the desired subject, and press the SET button. h When the subject is successfully targeted, a target frame icon (blue ) appears superimposed on the subject. h While the target frame icon is displayed, press the SET button. h The target frame icon (red ) continues to be displayed.
Shortcut setting (page 53) Assign functions (operation shortcuts) to the arrow keys when they are pressed while the Recording Screen is displayed. 1 ADVANCED OPERATION/SHOOTING 2 92 Select [SHORTCUTS], and press the SET button. : Assign the function when [I] is pressed. : Assign the function when [J] is pressed. : Assign the function when [G] is pressed. : Assign the function when [H] is pressed. RECOMMENDED SETTINGS: The most commonly used settings are automatically assigned.
5 ADVANCED OPERATION/SHOOTING 94 Press the MENU button. h The screen to confirm the shortcut settings appears, and then you are returned to the Recording Menu. h This completes the shortcuts setting. h On the screen in step 1, press the MENU button, and the screen to confirm the shortcut settings appears.
Exposure compensation By assigning the exposure compensation operation shortcut to an arrow key (page 92), you can make the image lighter or darker when capturing images. 1 2 Press the arrow key to which the operation shortcut was assigned. h The exposure compensation bar appears. Press [G] or [H] to adjust the exposure. h The exposure compensation numerical value is shown at the left end of the exposure compensation bar. h The exposure compensation can be set to a value from –1.8 to +1.8.
PLAYBACK ADVANCED OPERATION/PLAYBACK PLAYBACK MENU 1 To access and use the Menu Screen, see page 45 to 47. Slideshow settings (page 54) Specify the settings for playing back files continuously in a “slideshow” format. In a slideshow of photos, you can set the transition time, transition effects and BGM. Changing a setting ADVANCED OPERATION/PLAYBACK 1 2 3 Select the item you wish to change, and press the SET button. Press [I] or [J] to change the setting.
File protect setting (page 54) Prevent accidental erasure of image and audio files. Protect files one by one 1 2 4 Select [PROTECT] and press the SET button. Select [PROTECT SINGLE] and press the SET button. h [LOCK] appears. h If the protect mode has already been enabled for the file, then [UNLOCK] appears. Select [LOCK] and press the SET button. h The protect mode is set for the file. h The protect mark indicates that the file is locked.
Protect selected files Select multiple files to protect. 1 Display the Playback Menu 1 (page 45). 2 Select [PROTECT] and press the SET button. 3 ADVANCED OPERATION/PLAYBACK Select [PROTECT SELECTED] and press the SET button. h Use the arrow keys to move the yellow frame to the file you wish to protect. 20.12.2011 14:25 1080-60i 51.6MB SET LOCK 4 98 100-0006 00:00:25 Press the SET button. h The selected file is marked with the protect icon .
Rotate (page 54) Captured photos can be rotated to the correct orientation for viewing. HINT i An image for which the protect mode has been enabled cannot be rotated. To rotate a protected image, cancel the protect mode before beginning the rotate image procedure (page 97). Resize (page 54) HINT Why can not the image be resized? i An image can be resized only to a smaller (or the same) size, not to a larger size.
PLAYBACK MENU 2 To access and use the Menu Screen, see page 45 to 47. Correcting red-eye (page 55) Repair the red-eye effect in photos to make the eyes appear more natural. In the case of [SAVE AS NEW], the latest image number is assigned to the photo when it is saved. ADVANCED OPERATION/PLAYBACK HINT If the “Red-eye correction not successful” message appears... i The camera was not able to successfully repair the image.
Editing videos (page 55) You can trim away unwanted portions from a video and save it as a new video (video trimming [extracting]). You can also join videos together and save them as one separate clip (“splicing”). Procedure to trim (extract) a portion of a video 1 Specify the frames (1, 2) where the video is to be split. 2 B C J Extract the specified portion. [Two ways to split the video] i Trim away portions A and C, and save portion B. i Delete portion B, and join portions A and C.
Procedure to splice videos Specify the video that will come first. J Specify the video clip that you wish to append (splice). ADVANCED OPERATION/PLAYBACK J Splice the videos. i The videos are spliced. i The original videos are not affected. (You can also choose to erase the original videos when the new video is saved.) When editing videos... i When editing videos, do not turn off the camera, as doing so may erase the original video.
Video trimming (extracting) 1 2 Select the video to be trimmed from the 8-image display. h Move the yellow frame to the video you wish to trim (page 69). Display the Playback Menu 2 (page 45), select [EDIT VIDEO], and press the SET button. EDIT VIDEO SET ENTER 3 Select [SPLIT] and press the SET button. h The Split Screen appears.
4 ADVANCED OPERATION/PLAYBACK Specify the start point of the extract. h Play the video until approximately the desired point, pause the video then play the video one frame at a time, stopping at the start point of the extract. This will be the first frame of the extract. h If the start point of the video is also the start point of the extract, proceed to step 5. Play: After pausing playback, press and hold [H] for about 2 seconds for forward playback, or [G] for reverse playback.
5 Press the [O] button or [@] button. h A screen appears for you to select either to save the edited video as a new (separate) file, or to delete the original video and replace it with the edited video. SAVE AS NEW: The edited video will be saved as a new file. The original video remains unchanged. OVERWRITE: The original video will be deleted. Only the edited video will be saved. REVIEW CLIP: Play back the edited video before saving it.
7 Select the desired option, and press the SET button. h Editing starts. h When editing videos, do not turn off the camera, as doing so may erase the original video. h When editing ends, you are returned to the Playback Menu. ADVANCED OPERATION/PLAYBACK HINT i You will not be able to overwrite the file if the original file is protected. i If the “CARD FULL.” or “Built-in Memory full.” message appears, you will need to free some of the memory by deleting files that you do not need to keep.
Splicing (joining) videos HINT i Videos that were recorded in different modes cannot be spliced. 1 Display the Playback Menu 2 (page 45), select [EDIT VIDEO], and press the SET button. EDIT VIDEO SET 2 Select [SPLICE] and press the SET button. h The 8-image playback display for videos appears. 20.12.2011 1080-60i SAVE 3 ENTER Move the yellow frame to the video you wish to splice, and press the SET button. h The specified video is labeled with a number. h Up to 9 videos can be selected.
4 ADVANCED OPERATION/PLAYBACK 5 Press the [O] button or [@] button. h A screen appears for you to select either to save the spliced video as a new (separate) file, or to delete the original videos and replace them with the joined video. SAVE AS NEW: The spliced video clip will be saved as a new file. The original videos remain unchanged. OVERWRITE: The original videos will be deleted. Only the joined video will be saved. REVIEW CLIP: Play back the spliced video before saving it.
VQT3P45 109 ADVANCED OPERATION/PLAYBACK HINT i If the file size of the video after editing exceeds 4 GB, it is not possible to either “SAVE AS NEW” or “OVERWRITE”. i You will not be able to overwrite the file if the original file is protected. If you want it to be erased, you will need to first remove the protection (page 97). i If the “CARD FULL.” or “Built-in Memory full” message appears, you will need to free some of the memory by deleting files that you do not need to keep.
Copy (page 55) Files can be copied from the built-in memory to the SD card. 1 2 ADVANCED OPERATION/PLAYBACK 3 Display Playback Menu 2, select [COPY], and press the SET button. h The Copy Screen appears. Select the desired option, and press the SET button. [COPY SINGLE]: Copy files one at a time. [COPY SELECTED]: Copy selected files (page 111). [COPY ALL]: Copy all the files. h Use the arrow keys to select the file you wish to copy. h Proceed to step 3.
Copying selected files Copy multiple selected files. 1 2 3 Select [COPY SELECTED], and press the SET button. h The screen to select files appears. Use the arrow keys to move the yellow frame to a file you wish to copy, and press the SET button. h A checkmark is superimposed on the selected file. h To deselect a file, move the yellow frame to the file, and press the SET button. Press the [O] button or [@] button. h Copying begins. h When copying is completed, you are returned to the Playback Menu.
FILE INFO DISPLAY You can check what the settings were when a file was recorded with your camera. 1 2 ADVANCED OPERATION/PLAYBACK 3 Set the camera to the playback mode (page 44). Select the image for which you wish to display the information. h Toggle the SET button up, down, left or right to move the yellow frame to the file you wish to play back. Press the MENU button for at least 1 second. h The Information Screen appears. h If the MENU button is pressed again, the Information Screen is cancelled.
OPTION SETTINGS OPTION SETTINGS DISPLAY THE OPTION SETTING MENU The camera settings are executed via the Option Setting Menu. 1 Turn on the camera, and press the MENU button. RECORDING MENU 1 1 REC MODE 2 PICTURE SIZE 3 1 2 3 SCENE MODE COLOUR MODE FLASH SELF TIMER SET ENTER 1080-30p 16M-S Option tab Select an Option tab (1, 2 or 3). h The Option Setting Menu appears. h If you press [H], the screen to select a setting to change appears.
INTRODUCTION TO THE OPTION SETTING MENU Tab 1 1 2 3 OPTION SETTINGS 1 2 3 OPTION MENU 1 CLOCK SET ALERT SOUND DISPLAY ECONOMY BRIGHTNESS 1 2 3 4 5 ENTER 6 114 VQT3P45
4 ECONOMY setting (page 40) h Specify the elapsed period of inactivity before the sleep mode (to conserve battery power) is activated. BATTERY: REC: Set the elapsed time before the sleep mode is activated in the recording mode when using power from the battery. BATTERY: PLAY: Set the elapsed time before the sleep mode is activated in the playback mode when using power from the battery.
Tab 2 OPTION MENU 2 LANGUAGE TV OUTPUT INITIAL SET 1 FORMAT 2 3 ENTER 1 2 3 1 2 3 4 5 OPTION SETTINGS 116 VQT3P45
OPTION SETTINGS 1 LANGUAGE setting h Select the language in which the LCD monitor messages are displayed. 2 TV OUTPUT setting (page 120) 3 INITIAL SET h Reset the camera settings to the factory-preset settings. h The following settings do not change with this procedure: Date and time setting Language setting 4 FORMAT (page 128) FORMAT: Logical format of the SD card or the built-in memory is executed. DELETE DATA: Physical format of the SD card or the built-in memory is executed.
Tab 3 1 2 3 OPTION MENU 3 REC FOLDER FILE NO.
1 REC FOLDER setting (page 124) (when the recording mode is active) h Select a folder to record to. 2 PLAYBACK FOLDER setting (page 125) (when the playback mode is active) h Select a folder to play back. 3 FILE NO.
TV output setting (page 117) Specify the type of image signal that is output from your camera’s USB/AV terminal. 1 OPTION SETTINGS 2 Select [TV OUTPUT], and press the SET button. TV SYSTEM: Set the type of TV signal that is output from the USB/AV terminal. TV ASPECT: Set the TV’s aspect ratio. HDMI: Set the signal that is output from the HDMI terminal. VIERA Link: Set the VIERA Link function.
ON: Use the VIERA Link. OFF: Do not use the VIERA Link. 3 Press [I] or [J] to select the desired parameter. 4 Press the SET button. 5 Press the MENU button 2 times. h This completes the TV output setting.
Relation between [TV ASPECT] setting and TV display The tables below show the video signal that is output when the [TV ASPECT] setting is changed. However, note that for some TVs that have an auto-detect function, the output may not conform to the table, or the TV display may not change at all.
[TV ASPECT] setting TV type to be connected Image file to be displayed TV display Photo (4:3) 16:9 16:9 Video in SD mode Video in HD mode VQT3P45 123 OPTION SETTINGS HINT If the TV display is not correct… i If the appearance of the image on the TV monitor is not correct, you can either change the camera’s [TV ASPECT] setting, or change the screen size setting on your TV. To change the screen size setting on your TV, please refer to the instruction manual for your TV.
Storage folder setting (page 119) Create or select a recording folder (a folder in which to store recorded files). 1 2 OPTION SETTINGS 3 Set the camera to the recording mode, and display the Option Setting Menu. Select [REC FOLDER], and press the SET button. h Select [CREATE NEW FOLDER].
Playback folder setting (page 119) If the card contains multiple folders, you can select from which folder you would like to play back. 1 2 Set the camera to the playback mode, and display the Option Setting Menu. Select [PLAYBACK FOLDER] and press the SET button. PLAYBACK FOLDER 100CDPFP 101CDPFP 102CDPFP ENTER Press [I] or [J] to select the desired playback folder, and press the SET button. h The files in the selected folder are displayed in the Playback Screen.
File No. continued setting (page 119) If a newly formatted card is used, the file name (image number) of the captured image automatically begins from 0001. If the card is subsequently reformatted, or if a different reformatted card is used, the file names again begin from 0001. Card A File name (image number) 0001, 0002 ...... 0012, 0013 Replace card Card B 0001, 0002 ......
i If Card B already has files in it when it replaces Card A, file names are assigned as follows. When the highest file number on Card B (before replacing) is lower than the highest file number on Card A: the file name of the next recorded image continues from last file name recorded on Card A. Card A 0001, 0002 ..... 0012, 0013 Replace card Card B 0001, 0002, 0014, 0015 .....
Formatting (initialising) (page 117) A card must be formatted with this camera: i After purchasing, when used for the first time, or i If it was formatted using a personal computer or other device. The card cannot be formatted if the lock switch is set to the “LOCK” position. Proceed with the format procedure after setting the lock switch to the unlocked position (page 26). OPTION SETTINGS HINT Caution during formatting i Do not turn off the power to the camera or eject the card during formatting.
CHECKING THE REMAINING CARD MEMORY You can check how many images can be captured, how much video recording time and how much audio recording time is available on the card. For a table showing the recording capacities of SD cards, please see pages 189 to 191. Checking the remaining number of images and video recording time 1 Remaining video recording time VQT3P45 129 OPTION SETTINGS Set the camera to the recording mode (page 44).
Check the available audio recording time 1 Set the camera to the audio recording mode (page 79). h The remaining audio recording time is shown. Remaining audio recording time 0.3M 374 016:30:36 OPTION SETTINGS HINT i When the remaining number of images or the remaining video recording time is “0”, you cannot capture any more images. To capture more images, either install a new card, or save the images to a computer and then delete them (pages 54 and 73) from the card.
CHECKING THE REMAINING BATTERY PACK CHARGE When using the battery pack, the remaining battery pack charge can be checked on the LCD monitor. Make sure to check this indicator before capturing an image. For an indication of the possible length of time for battery pack operation, see page 30.
Battery pack remaining charge indicator Battery remaining charge Approx. full. Power is low. It will soon be impossible to capture or play back images. Recharge the battery pack. OPTION SETTINGS HINT i If any file is present, you can also check the remaining battery pack charge on the file information display (page 112). i Battery life may differ even among battery packs of the same type.
OTHER DEVICES AND CONNECTIONS CONNECTING TO A COMPUTER CONNECTING TO A COMPUTER SETTING THE CONNECTION MODE 1 2 Start your computer, and use the supplied USB cable to connect the camera to the computer. h Connect the camera’s USB/AV terminal to the computer’s USB terminal. Turn on the camera (page 39). h The screen to select the computer connection mode appears. CARD READER: Use the camera as an external drive of the computer (card reader mode). WEB CAMERA: Use your camera as a webcam (webcam mode).
HINT About the USB cable i Use only the supplied USB cable. Operation is not guaranteed if a different USB cable is used. i When using the SDXC Memory Card with a computer, please visit the support web site shown below. http://panasonic.net/avc/sdcard/information/SDXC.html If the “Disconnect USB cable” message appears... i Disconnect the USB cable once, then connect it again.
USING AS A CARD READER Mounting your camera 1 2 3 Set the camera to the card reader mode (page 133). h The message [Found New Hardware] appears in the task tray, showing that the camera is recognised as a drive. h The card is recognised (mounted) as a disk, and the [CAM_SD (E:)] icon appears in the [My Computer] window. h The drive name (E:) may be different on your computer. Select an action. h If the [CAM_SD (E:)] window appears automatically, select the desired procedure from the window.
ABOUT THE CONTENTS OF THE CARD Configuration of directories in the card ROOT DCIM 100CDPFP IMGA0001.jpg Folder number IMGA0002.jpg Image number IMGA0003.mp4 IMGA0004.m4a 101CDPFP IMGA0001.jpg IMGA0002.jpg IMGA0005.jpg Image or audio recording number IMGA0999.jpg 102CDPFP IMGA0001.jpg IMGA0002.jpg h Up to 999 files can be stored in folder 100CDPFP. If more files are made, a folder named 101CDPFP is created, and they will be stored in there. New folders will then be named in sequence, i.e.
When using as a card reader i Do not alter files or folders in your camera in any way. Doing so may result in your camera not recognising that data. If you want to edit files, first copy them to your computer’s hard drive. i Cards formatted on your computer cannot be used by your camera. Format all cards to be used by your camera with your camera.
About audio files recorded with this camera i Files can be played back using QuickTime. Using Windows Explorer or other programmes on the PC to copy, move or rename files and folders recorded with this unit will result in them being unusable with HD Writer VE 1.0. To access the files in the built-in memory i Remove the card from the camera before connecting the camera to a computer. i The volume name becomes [CAM_MEM(E:)]. h The drive name (E:) may be different on your computer.
k Copying files from the camera’s built-in memory and/or the SD card to your PC Card reader function (mass storage) (page 133) Files from the camera’s built-in memory and/or the SD card can be copied to the PC with Explorer or other programmes. 1 2 Double click the folder that contains the still pictures. ([DCIM] _ [100CDPFP] etc.) Drag and drop the files into the destination folder (on the PC’s HDD). HINT i Do not delete the SD card’s folders. Doing so may make the SD card unusable in this unit.
USING AS A WEBCAM This camera can be used as a webcam.
* Operation is not guaranteed for all computers even if the recommended system requirements are fulfilled. * Operation is not guaranteed for NEC PC-98 series and their compatible devices * Windows 3.1, Windows 95, Windows 98/98SE, Windows Me, Windows 2000 and Windows NT are not supported. * Operation on an upgraded OS is not guaranteed. Mac Computer Mac OS Mac OS X 10.6.
WHAT YOU CAN DO WITH A COMPUTER Contents of the supplied CD-ROM HD Writer VE 1.0 You can copy the video/photo data to the HDD of a computer or write to media like DVD discs or SD cards using HD Writer VE 1.0. Refer to the operating instructions of HD Writer VE 1.0 (PDF file) for details on how to use it. * Videos that were edited using HD Writer VE 1.0 can be played back on this camera. However, they cannot be edited with this camera.
Available function Data type Copying data to a computer Video and photo Copying to DVD: i Converted to conventional standard quality (MPEG2 format). Editing: Video data copied to the HDD of a computer can be edited. i Add titles and transition effects, trimming, splitting i Extract frames from the video Online sharing: You can upload videos on the Internet and share them with your family and friends. Playing back on a computer: Play back the video data in high definition picture quality on a computer.
HINT i The software cannot process audio files. i Writing data from a computer to this unit’s built-in memory of this unit is not possible. i Videos that have been recorded on another device cannot be written to the software supplied with this unit. i We cannot guarantee operation if you use software other than that supplied to read/write videos. i Do not start the software supplied with this unit and other software at the same time.
Article 2 Use by a Third Party Licensee may not use, copy, modify, transfer or allow any third party, whether free of charge or not, to use, copy or modify the Software, except as expressly provided for in this Agreement. Article 3 Restrictions on Copying the Software Licensee may make a single copy of the Software in whole or a part solely for backup purposes. Article 4 Computer Licensee may use the Software only on one computer, and may not use it on more than one computer.
OPERATING ENVIRONMENT i Even if the system requirements mentioned in this operating instructions are fulfilled, some computers cannot be used. i A CD-ROM drive is necessary to install the supplied software applications. (A compatible DVD writer drive and media are necessary for writing to a DVD.) i Operation is not guaranteed in the following cases. h When 2 or more USB devices are connected to a computer, or when devices are connected through USB hubs or by using extension cables.
RAM Display Sound Drive Interface USB connectable model Applicable content Image data recorded on a Panasonic video camera that this software is supplied with VQT3P45 147 CONNECTING TO A COMPUTER Free hard disk drive space Windows 7: 1 GB or more (32 bit)/2 GB or more (64 bit) Windows Vista: 1 GB or more Windows XP: 512 MB or more (1 GB or more recommended) High Colour (16 bit) or more (32 bit or more recommended) Desktop resolution of 1024×768 pixels or more (1920×1080 pixels or more recommended)
Other Mouse or equivalent pointing device, SD card reader/ writer (required for reading and recording to SD cards; performing these operations with SDHC memory cards or SDXC memory cards requires an SDHC-compatible or SDXC-compatible SD card reader/writer), an environment with Internet access (required for online functions “Online sharing”) CONNECTING TO A COMPUTER i Supplied CD-ROM is available for Windows only.
To use the HD Writer VE 1.0 You will need a high performance computer depending on the functions to be used. It may not properly play back or properly operate depending on the environment of the computer used. Refer to the operating environment and notes. HINT i Operation during the playback may become slow if the CPU or memory is not fulfilling the requirements of the operating environment. i Always use the most current driver for the video card.
Operating environment for the card reader function (mass storage) Computer OS CONNECTING TO A COMPUTER CPU RAM Interface Other requirements IBM PC/AT compatible PC Microsoft Windows XP (32 bit) Home Edition Service Pack 3 Microsoft Windows XP (32 bit) Professional Service Pack 3 Microsoft Windows Vista (32 bit) Home Basic Service Pack 1/Service Pack 2 Microsoft Windows Vista (32 bit) Home Premium Service Pack 1/Service Pack 2 Microsoft Windows Vista (32 bit) Business Service Pack 1/Service Pack 2 Micro
INSTALLATION When installing the software, log on to your computer as the Administrator or with a user name with equivalent authorisation. (If you do not have authorisation to do this, consult your manager.) i Before starting the installation, close all applications that are running. i Do not perform any other operations on your computer while the software is being installed. i Explanation of operations and screens is based on Windows Vista. 1 Insert the CD-ROM into the computer.
4 Select the country or region where you live, then click [Next]. h If the country or region cannot be selected, select [NTSC Area]. h When the confirmation message appears, click [Yes]. Click 5 Select where the application is to be installed, then click [Next]. Click CONNECTING TO A COMPUTER 6 7 8 Select [Yes] or [No] to create shortcut. h A message regarding the playback in the environment used may be displayed depending on the performance of the computer used. Click [OK] after confirming.
9 Select [Yes, I want to restart my computer now.], then click [Finish]. The computer must be rebooted for the application to work.
Uninstalling HD Writer VE 1.0 Follow the steps below to uninstall any software applications that you no longer require. 1 Select [Start] →[Control Panel] →[Programs and Features]. Click CONNECTING TO A COMPUTER 2 Select [HD Writer VE 1.0], then click [Uninstall]. h Proceed with the uninstallation by following the on-screen instructions. h After uninstalling the software, be sure to reboot the computer.
STARTING HD WRITER VE 1.0 i When using HD Writer VE 1.0 on Windows XP, log on to your computer as Administrator (or with a login name equally authorised). If you log on with a login name other than Administrator, you cannot use the applications. i When using HD Writer VE 1.0 on Windows Vista/Windows 7, log on to your computer as Administrator (or with a login name equally authorised) or with the user name for a standard user account.
Reading the operating instructions of the software applications i You will need Adobe Acrobat Reader 5.0 or later or Adobe Reader 7.0 or later to read the PDF operating instructions. Select [Start] → [All Programs] → [Panasonic] → [HD Writer VE 1.0] → [Operating Instructions].
IF USING Mac i HD Writer VE 1.0 is not available for Mac. i iMovie ’11 is supported. For details about iMovie ’11, please contact Apple Inc. Operating environment Computer OS CPU RAM Interface Mac Mac OS X 10.6.6 Intel Core Duo 1 GB or more USB port i Even if the system requirements mentioned in this operating instructions are fulfilled, some computers cannot be used. i Operates with the OS standard driver. i Supplied CD-ROM is available for Windows only.
To disconnect USB cable safely Drag [CAM_SD] or [CAM_MEM] on the Desktop to the [Trash], and then disconnect the USB cable. HINT About the USB cable i Use only the supplied USB cable. Operation is not guaranteed if a different USB cable is used. i Do not remove the SD card from this unit when this unit is connected to the computer using a USB cable.
CONNECTING TO A TV CONNECTING TO A TV CONNECTING TO A TV By connecting the camera to a TV, you can play back files from the installed SD card or the built-in memory on the TV. HINT Insert and pull out the cable carefully i When connecting the cables, make sure that the cable plugs are correctly oriented and that they match the shapes of the terminal sockets on the devices. Push the plugs in straight when connecting them.
Connecting to a video input terminal Use the supplied AV cable to connect to a TV. Insert the plugs as far as they will go. Set the input to “VIDEO”. AV cable (supplied) To USB/AV terminal White plug:To Audio Input (L) terminal Red plug:To Audio Input (R) terminal Yellow plug:To Video Input terminal CONNECTING TO A TV i Do not use any other AV cables except the supplied one. Connecting to the HDMI terminal Use a separately sold HDMI mini cable to connect to a TV.
PLAYING BACK ON A TV i After connecting the camera to the television, switch the TV input to the terminal to which the camera is connected. i The same playback procedure as when playing back with the camera is used to play back audio recordings as well. i The playback method is the same as when viewing images on the camera’s LCD monitor. (Use the TV controls to adjust the volume.
3 Operate with the remote control for the TV. 1) 1) 20.12.2011 0:00 3.5MB SET 101-0216 ENTER 2) 2) 1 2 20.12.2011 3) 3) 1 3 CONNECTING TO A TV 20.12.2011 1) Press the button up, down, left or right to select a scene or photo to be played back, and then press the button in the centre to set it. 2) Navigate the operation icons that are displayed on the TV screen with the remote control for the TV.
HINT i If you are unsure whether or not the TV and AV amplifier you are using are compatible with VIERA Link, read the operating instructions for the devices. i Operation is not possible with a cable that is not based on the HDMI standard.
COPYING/DUBBING COPYING/DUBBING COPYING/DUBBING Dubbing in standard picture quality Images played back on this unit can be dubbed onto a DVD recorder or video device. i Images can be played back even on devices other than highdefinition compatible devices, so this is recommended when dubbing videos for distribution. Change the video input on the video device and TV that this unit is connected to. i The channel set will differ depending on the terminal to which the unit is connected.
3 Start recording on the connected device. h To stop recording (dubbing), stop playback on this unit after stopping recording on the recorder. h It is not possible to directly insert in the card slot an SD card recorded with this camera and play back or dub from it. h It is not possible to connect the camera to the USB connector and play back or dub from it. h It is not possible to record in HD with a Blu-ray disc recorder.
IMPORTANT MESSAGES AND ALERTS IMPORTANT MESSAGES AND ALERTS COMMONLY ASKED QUESTIONS IMPORTANT MESSAGES AND ALERTS If you have a question about the camera operation, you might find the answer in this compilation of commonly asked questions. Question Why does not the power turn on? Why is the battery pack consumed so quickly even after it was fully recharged? Answer Due to cold temperatures, the battery pack temporarily lost its power. The ambient temperature is very low.
Answer — Which resolution setting should I use? — Action Except for some settings, such as the exposure setting and exposure compensation, all the settings are retained even after the camera is turned off. Select the resolution setting according to the intended use. Picture quality w or better: Appropriate for printing letter-size or larger, and for printing a close-up of part of a photo (trimming). , G, t: For printing standard photo (photo service) sizes.
IMPORTANT MESSAGES AND ALERTS Question What is the difference between the digital zoom and the optical zoom? Answer — How can I get the distant view into focus? — Shooting LCD monitor When used in cold weather, why does the image seem to leave traces as it moves? Why does the displayed image contain some red, blue and green dots, or why are black spots visible? 168 VQT3P45 Condition due to the LCD monitor characteristics.
Answer The subject was too bright. Why is the image out of focus? The focus is not locked properly. Why is there no image? This may happen when trying to play back images stored on a card from a different digital camera. If the subject moves or the camera is moved during recording, a distorted image may sometimes occur. Viewing images Why is the playback image distorted? Action When capturing an image, devise a way to compensate for a bright subject, for example, by changing the shooting angle.
Question Why is not the magnified image clear? IMPORTANT MESSAGES AND ALERTS Why is not the captured image clear? Can I play back image and sound files that I edited using my computer? Viewing images Why is there a motor-like sound during video playback? Round white spots that look like bubbles are appear in photos. Connecting to a TV Why is there no sound? 170 VQT3P45 Answer Due to the characteristics of the camera, magnified images appear less clear. The image was captured using the digital zoom.
Misc. Why is a noise heard from a nearby TV or radio during battery recharging? Why does the “CARD FULL.” or “Built-in Memory full.” message appear? Why does the “Card is protected” message appear? Why can not the camera be operated? A problem such as inability to record or play back occurs. Some parts of the unit, such as the battery cover or terminal cover, cannot be moved. Answer You have attempted to splice videos that were recorded in different recording modes.
Question Can I use my camera abroad? IMPORTANT MESSAGES AND ALERTS Misc. Why does the “ERROR OCCURRED. PLEASE TURN UNIT OFF, THEN TURN ON AGAIN.” message appear? 172 VQT3P45 Answer — A problem has occurred within the camera or card. Action You can charge the battery and connect to a TV to view your recordings when abroad. Check the following items: 1 Remove the card and then install it again. 2 Remove the battery pack and then install it again. 3 Install a different card. If “ERROR OCCURRED.
TROUBLESHOOTING Camera Problem No power. Power A blinking temperature warning icon is shown, and the camera does not turn on. The camera turns off by itself. Cause The battery pack is dead. The battery pack has not been inserted correctly. The battery pack is too hot. Action Reference page Recharge the battery pack, or replace with a fully charged battery pack. Or connect the AC adaptor. Insert the battery pack correctly. 30 Wait for the battery pack to cool down.
IMPORTANT MESSAGES AND ALERTS Problem Cause Action An image is not captured when the [O] button or [@] button is pressed. The power is not turned on. If the camera has switched to the sleep mode, turn on the camera before shooting. If the camera was turned off, press the power button to turn it on. Install a new card. Delete the images that are not necessary. Shooting The flash does not operate.
Cause Action The digital zoom does not work. There is noise in the captured image. The digital zoom setting is set to . The ISO sensitivity setting is too high. The camera’s internal temperature is high. Set the digital zoom setting to . Set the ISO sensitivity to a lower setting. Shooting The icon appears, and shooting is not possible. Reference page 53, 65 51, 86 Discontinue shooting, and wait for the camera to cool down before using it again.
Problem LCD monitor No playback image appears. IMPORTANT MESSAGES AND ALERTS The image is too dark. Cause Action The camera is not set to the playback mode. The flash was blocked by a finger or other object. Set the camera to the playback mode. The subject was too far away. Viewing images The subject was lit from behind. There is not enough light. 176 VQT3P45 Hold the camera correctly, and make sure the flash is not obstructed. Capture the image in the range of operation of the flash.
Problem The image is too bright. Viewing images The flash mode is set to m. The subject was too bright. The ISO sensitivity setting is incorrect. The subject is too close to the camera. The focus setting is not correct. The camera moved when the [O] button was pressed. (camera shake) The focus is not locked properly. The lens is dirty. Action Select a flash mode other than m. Use the exposure compensation function. Set the ISO sensitivity to =.
IMPORTANT MESSAGES AND ALERTS Problem Cause The colours of the images captured indoors are not correct. This is due to ambient lighting. The white balance setting is incorrect. The handstrap or a finger was blocking the lens. A part of the image is missing. Viewing images “No image” is shown. During audio playback, there is no sound. Connecting to a TV There is no colour in the image. The image is distorted. 178 VQT3P45 There is no file in the built-in memory or in the installed card.
Problem No image or sound. Image editing Charging The edge of the image is cut off. You cannot edit or rotate an image. The battery pack is not charging. The “This file is protected” message appears and the file cannot be deleted. Misc. The recording capacity is less than that shown in the tables on pages 189 to 191. Action The camera is not correctly connected to the TV. Follow the instructions to make the connection correctly. Set the TV input to the correct setting. Not a malfunction.
Restrictions concerning the Scene Mode and Colour Mode features Scene Mode restrictions IMPORTANT MESSAGES AND ALERTS Setting Restrictions Sports Portrait Colour mode: Fixed at . Focus: Fixed at *. Exposure setting: Fixed at @. Spotlight Snow Beach Sunset Fireworks Landscape 180 VQT3P45 Colour mode: Fixed at . Focus: Fixed at *. Exposure setting: Fixed at @. White balance: Fixed at >. Colour mode: Fixed at . Focus: Fixed at *. Flash: Fixed at . ISO sensitivity: Fixed at =.
Setting Night scenery Under water Low light* Colour mode: Fixed at Focus: Fixed at *. Exposure: Fixed at @. . . Colour mode: Fixed at . Focus range: Fixed at *. Exposure: Fixed at @. Colour mode: fixed at . Focus: Fixed at *. Flash: Fixed at . ISO sensitivity: Fixed at =. Exposure: Fixed at @. * In some cases, the shutter speed may decrease to 1/15 sec. HINT When shooting hi-speed bursts... i The shutter speed will be faster than 1/30 sec. When recording a video...
About the scene mode function and focus setting i The scene mode changes to when the focus is set to or -. i Even if the focus is set to or -, it changes to * when the scene mode is set to any setting other than . IMPORTANT MESSAGES AND ALERTS About the status indicator when charging the battery pack When the status indicator is flashing fast or slow, it may indicate one of the following conditions.
ABOUT COPYRIGHT It is forbidden to copy the software accompanying this unit, or to reproduce it on a network, without permission. k Licenses i SDXC Logo is a trademark of SD-3C, LLC. i HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. i Microsoft®, Windows® and Windows Vista® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
CAUTIONS FOR USE IMPORTANT MESSAGES AND ALERTS About the camera The camera and the SD card become warm during use. This is normal and is not a malfunction. Keep this unit as far away as possible from electromagnetic equipment (such as microwave ovens, TVs, video games etc.). i If you use this unit on top of or near a TV, the pictures and/or sound on this unit may be disrupted by electromagnetic wave radiation.
Do not use the camera for business purposes, such as for surveillance. i Continuous use could cause the camera to overheat and break. i This camera is not for commercial use. When you are not going to use the camera for an extended time i When storing the camera in a cupboard or cabinet, it is recommended that you place a desiccant (silica gel) in with it.
IMPORTANT MESSAGES AND ALERTS i Extremely high or low temperatures will shorten the life of the battery. i Environments that are hot, humid or oily can rust the terminals and damage the battery. i If storing the battery for an extended period of time, it is recommended that you charge it once a year, use it until it is depleted, and store it again. Remove any dust adhering to the battery terminals. Prepare spare batteries when going out.
i When used for an extended period of time, the camera surface and the SD card may become rather warm, but this is not a malfunction. Caution when disposing of or transferring SD cards i Using this camera or a computer to format an SD card only changes the file management information and does not completely delete the card data. i It is recommended that the SD card be physically destroyed, or that this camera be used to physically format the card if giving it to someone else.
IMPORTANT MESSAGES AND ALERTS The LCD monitor is manufactured using highprecision technology; however, black spots may appear on the screen or some pixels (red, blue or green) may stay lit. This is normal and is not a malfunction. The effective pixel rate of the LCD monitor is maintained at a very accurate 99.99%, and dead or stuck pixels may occur in at most 0.01% of the pixels. Note that these pixel defects are not recorded with the captured images and are not a cause for concern.
RECORDING MODES/APPROXIMATE RECORDABLE TIME When using a Mac for 2 playback/ editing 1 Recording mode Picture size *1 1920× 1080 *1 1920× 1080 *1 *1 1280× 1280× 720 720 < *2 640× 480 960× 540 Voice memo 4 GB 20 min 30 min 30 min 50 min 2h 20 min 20 min 32 h 16 GB 1h 2h 2h 3h 9h 1h 50 min 10 min 10 min 30 min 50 min 20 min 131 h 64 GB 7h 8h 8h 13 h 30 min 30 min 30 min 30 min 32 h 5h 20 min 532 h Built-in Approx.
IMPORTANT MESSAGES AND ALERTS i When the recording mode setting is set to audio recording <, and the recording exceeds about 5 hours, the recorded file is saved and the audio recording ends. For other recording mode settings, when the file size exceeds 4 GB, the recorded file is saved once, and the recording continues in a new file. (These 4 GB segments are automatically created. The recording session continues until you stop recording.
APPROXIMATE NUMBER OF RECORDABLE PICTURES k Photo recording (single-shot) Recording pixels SD card Built-in memory 4 GB 16 GB 64 GB Approx. 80 MB A 4608×3456 400 1900 7900 10 15 1920×1080 5200 21200 82300 1600×1200 5400 22100 82300 Built-in memory 4 GB 16 GB 32 GB Approx.
OPTIONAL ACCESSORIES IMPORTANT MESSAGES AND ALERTS Product numbers correct as of February, 2011. These may be subject to change.
SPECIFICATIONS Specifications are subject to change due to performance upgrades. IMPORTANT MESSAGES AND ALERTS Digital Movie Camera Power source: DC 5.0 V (when using AC adaptor) 3.7 V (when using battery) Power consumption: Recording: 2.3W Signal system: 1080/60i, 1080/30p, 720/60p, 720/30p, 480/30p, 540/30p Recording format: Video: MPEG-4 AVC/H.264 file format compliant, iFrame Voice memo: MPEG-4 AAC audio Image sensor: 1/2.3 type (1/2.3”) MOS image sensor Total: Approx. 16,790,000 pixels (16.
Zoom: (Photo) 5× optical zoom; (Video) 12× (30p)/6× (60i/60p) advanced zoom Digital zoom; 120× (video mode, 30p mode), 60× (video mode, 60i/60p mode), 50× (photo mode) IMPORTANT MESSAGES AND ALERTS Image stabiliser: Electronic Monitor: 6.7 cm (2.6”) wide LCD monitor (Approx.
AV multi connector audio output: 155 mV, output impedance 220Ω, 2 ch IMPORTANT MESSAGES AND ALERTS HDMI mini connector audio output: Linear PCM USB: Reader/writer function SD card: Read only Built-in memory: Read only Hi-Speed USB (USB 2.0), micro USB connector Webcam Compression: Motion JPEG Image size: 640×480 pixels Flash: Effective range: Approx. 80 cm to 2.1 m Dimensions (excluding projecting parts): 92.0 mm (W)×123.7 mm (H)×41.2 mm (D) Mass (weight): Approx.
Water-resistant: Compliant with JIS protection grade 8 standards (according to tests conducted in-house by Panasonic) Can be submerged at a maximum depth of 3.0 m, for up to 60 minutes. IMPORTANT MESSAGES AND ALERTS Battery operation time: See page 30 k Video Recording media: SD Memory Card (FAT12 and FAT16 system compliant) SDHC Memory Card (FAT32 system compliant) SDXC Memory Card (exFAT system compliant) Refer to page 25 for details concerning SD cards that can be used in this unit.
Audio compression: AAC (2 ch) Recording media: SD Memory Card (FAT12 and FAT16 system compliant) SDHC Memory Card (FAT32 system compliant) SDXC Memory Card (exFAT system compliant) Refer to page 25 for details concerning SD cards that can be used in this unit. Built-in memory: Approx. 80 MB Compression: JPEG (DCF/Exif2.
EU Pursuant to at the directive 2004/108/EC, article 9(2) Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15, 22525 Hamburg, Germany VQT3P45 M0411-0 1AG6P1P6322--(S) Panasonic Corporation Web site: http://panasonic.