Installation Guide Home Network System Window/Door Sensor Model No. KX-HNS101AZ Thank you for purchasing a Panasonic product. This document explains how to install the window/door sensor properly. For details about how to use the system, refer to the User’s Guide (page 17). Please read this document before using the unit and save it for future reference. HNS101AZ_(en_en)_0325_ver.031.
Table of Contents Introduction Accessory information ...............3 Important Information About this system ......................4 For your safety ...........................4 Important safety instructions ......5 For best performance ................5 Other information .......................6 Setup Part names and functions ..........7 LED indicator .............................7 Setup overview ..........................7 Inserting the battery ...................8 Registering the window/door sensor .
Introduction Accessory information Supplied accessories No. Accessory item/Part number A Battery*1 1 B Mounting screws (20 mm)*2 4 C Mounting double-sided tapes*3 3 *1 *2 *3 Quantity When replacing the battery, see “Power source” of “Specifications”, page 17 for battery information.
Important Information About this system R This system is an auxiliary system; it is not designed to provide complete protection from property loss. Panasonic will not be held responsible in the event that property loss occurs while this system is in operation. R The system’s wireless features are subject to interference, therefore functionality in all situations cannot be guaranteed.
Important Information R Do not touch the terminals and with metal objects. R Risk of explosion if battery is replaced by an incorrect type. Dispose of used battery according to local regulations. R If any electrolyte should come into contact with your hands or clothes, wash it off thoroughly with water. R If any electrolyte should come into contact with your eyes, never rub your eyes. Rinse your eyes thoroughly with water, and then consult a doctor.
Important Information R For maximum coverage and noise-free communications, place your hub: – at a convenient, high, and central location with no obstructions between the product and hub in an indoor environment. – away from electronic appliances such as TVs, radios, personal computers, wireless devices, or other phones. – facing away from radio frequency transmitters, such as external antennas of mobile phone cell stations. (Avoid putting the hub on a bay window or near a window.
Setup Part names and functions n Sensor unit A B C Indicator Status Red, blinking Sensor is out of range of the hub Green, blinking Registration mode (You pressed and held M N) Off No battery power Note: R The LED indicator does not indicate sensor status if the sensor has not been registered (page 8). Setup overview 1 n Magnet unit D Sensor unit cover M N Used to confirm the status of the sensor or register the sensor to the hub.
Setup operation was confirmed (page 13). Inserting the battery R USE ONLY a CR2 Lithium battery. R Confirm the polarities ( , ). 1 Remove the sensor unit cover. R Lift from the indented area (A) and open the sensor unit cover (B). This procedure is not required for devices that were included as part of a bundle. Before you can use the window/door sensor, it must be registered to the hub. If you purchased devices separately (i.e., not as part of a bundle), you must register each device to the hub.
Setup devices and group them by location. For more information, refer to the User’s Guide (page 17). Changing the sensor type You can select whether a window/door sensor functions as a window sensor or as a door sensor. For more information, refer to the User’s Guide (page 17). Wireless communication range The wireless communication range of each device in the system from the hub is approximately 50 m indoors and approximately 300 m outdoors.
Setup Temporary placement Before installing the window/door sensor, temporarily place it in the desired location and confirm that it operates properly by pressing M N. Important: R Attach the sensor unit to the window frame or door frame, and attach the magnet unit to the window or door. R The window/door sensor will not operate properly if the “ ” marks are too far apart or are not pointing toward each other. R Attach both units so that the “ ” marks point toward each other and are within 25.
Setup Example 1: Installed on the left side of a window Correct A 1 B Green 1 “ ” marks point directly at each other and are within 25.4 mm of each other. Result: When you press M N (A), the LED indicator lights in green (B). Incorrect 2 3 4 A B Red 2 “ ” marks are aligned but units are too far apart. 3 “ ” marks are aligned but window frame is too thick; units are too far apart. 4 “ ” marks are not aligned. Magnet unit is too high.
Setup Example 2: Installed on the right side of a window Correct 1 A B Green 1 “ ” marks point directly at each other and are within 25.4 mm of each other. Result: When you press M N (A), the LED indicator lights in green (B). Incorrect 4 3 2 A B Red 2 “ ” marks are aligned but units are too far apart. 3 “ ” marks are aligned but window frame is too thick; units are too far apart. 4 “ ” marks are not aligned. Magnet unit is too high.
Setup Installation Install the window/door sensor in the same position where proper operation was confirmed (page 10). You can install the window/door sensor using screws or double-sided tape, depending on your preference or the material of the installation area. Note: R When installing, make sure the battery is inserted properly and the sensor unit cover is completely closed. R Use screws when installing on a wooden surface. Do not use double-sided tape.
Setup 2 Sensor unit: Attach the sensor unit. 1 Screws 2 86.2 mm Magnet unit: Attach the magnet unit. 3 Screws 4 24.4 mm 1 3 4 2 3 1 3 5 Attach the covers. Important: R 5 Align the “ ” marks on the sensor unit and the magnet unit so that they point directly at each other and are no more than 25.4 mm apart. 14 HNS101AZ_(en_en)_0325_ver.031.
Setup Securing with double-sided tape Note: R Make sure the surfaces of the sensor unit, magnet unit, and the installation area are clean and dry before applying double-sided tape. 1 2 Check that the sensor unit cover and magnet unit cover are attached. Affix double-sided tape to the sensor unit and magnet unit. R Make sure the tape covers the screw holes on the back of each unit. 5 3 Install the sensor unit and magnet unit.
Appendix Testing the window/ door sensor You can check the window/door sensor’s LED indicator and test the performance of the window/door sensor. 1 Remove the sensor unit cover. 2 3 4 Press M N on the sensor unit. You can configure the window/door sensor to trigger other system events, such as camera recording, turning on an electric device (such as a lamp), etc. (Appropriate device required.
Appendix Accessing the User’s Specifications R Standards Guide The User’s Guide is a collection of online documentation that helps you get the most out of the [Home Network] app. 1 iPhone/iPad Tap in the app’s home screen. Android™ devices Tap or press your mobile device’s menu button in the app’s home screen. 2 Tap [User’s Guide]. Note: R Microsoft® Windows® Internet Explorer® 8 and earlier versions are not supported. R Android 4.1 or later versions are recommended.
Appendix Warranty (for New Zealand) Panasonic New Zealand undertakes to: Repair or at its option, replace without cost to the owner, either for material or labour, any part which is found to be defective within two years of the date of purchase. THIS EXPRESS WARRANTY DOES NOT COVER: 1) Pick up and delivery. 2) Batteries. 3) Repairs when the product has not been used in accordance with the Operating Instructions Manual or has been modified.
Notes 19 HNS101AZ_(en_en)_0325_ver.031.
For your future reference We recommend keeping a record of the following information to assist with any repair under warranty. Serial No. Date of purchase (found inside the sensor unit) Name and address of dealer Attach your purchase receipt here. For Australia Customer Care Centre Tel. No.: 132600 or website www.panasonic.com/au For New Zealand Customer Care Centre Tel. No.: (09) 272 0178 or website www.panasonic.