OPERATING ~ Brasserie INSTRUCTIONS waken. KX=F1000B L Contents Capt 1. Installation and Connection Capt 2. Initial Preparation Capt 3. Making and Answering Voice Calls Capt 4. Transmitting and Receiving Fax Calls Capt 5. Copier Function Capt 6. Automatic Dialing Please read these Operating Instructions before X using the unit and save for future reference. Capt 7.
Thank you for purchasing the Panasonic Plain Paper Facsimile. For your future reference \ Date of purchase Serial No. {found on the rear of e unit) Sealer's name and address Dealer’s telephone number Caution: «Note that the images of copied or received documents will remain on the used film. When disposing of the used film, use discretion. . «Do not rub the printed side or use an eraser on the printed side, as it may smear. «The used film is not reusable.
Table of Contents 1 and Connect Installing the film cartridge .. Installing the paper cassette installing the document sacker ..o 6 installing the document feeder tray Connections Location of controls Setting the date and time . Setting your logo How to enter characters and symbols 1 Setting your facsimile telephone number .
Top cover Head unit PUSH TO LOCK Note: 1 Open the top cover, 2 Press the green bunion on the right marked “PUSH" and lift up the head unit, 3 Place the cartridge with the “BACK” indicator facing up and tighten the film by winding the gears if there is slack. . incorrect Correct 29 @o 4 Place the "BACK” side of the cartridge into the unit, by inserting the pins on the sides of the green gears into the green holders. Then dower the front of the cartridge into place.
Installing the paper cassette You can use A4 size paper. The paper cassette can hold up to 250 sheets of 75 g/m? paper. Use 60 to 90 g/m? paper. cover Paper cassette SUPPORTS) Note: 1 Open the paper cassette cover. *When removing the paper cassette from the unit, lift it up slightly and pull it towards you Fan the stack of paper to avoid a paper jam. insert the paper by aligning the paps edges with the partition, «Most paper has instructions recommending the side to print on.
Installing the document sacker _Installing the document feeder tray Document Tray fin seeder tray ® Slot Holder Referring to the illustration to the left, insert the document sacker with the bent side facing up until it clicks into place. Helpful hint: To extend the document sacker, pull it towards you until it clicks into place.
Handset cord Power Cord ) Single telephone fine Telephone fine cord Power outlet d (220-240V) Note: «When you operate this product, the power outlet should be near the product and easily accessible. "\ e When a power failure takes place, you are only able o use the unit as a standard telephone. +You can connect an extension phone of a telephone answering machine to the unit. See page 21. Helpful hint: if assistance is needed, press (HELP). The unit will print a quick reference in English.
Location of controls Front view Speaker {p. 12) Microphone " Recording paper exi Paper cassette Document stack: Document entrance Front lid open lever (pp. 54, 55) Document feeder tray (p. 6) Document guide(s) {p. 15} Visual film indicator: shows the approximate amount of remaining file. FULL| Film |~ INDICATOR — Fli. M 33 e INDICATOR ‘Her the film indicator points to the position in the illustration above, the remaining firm produces approx. 85 pages of Ad size document.
Control panel VOLUME buttons (p. 12} R button {p. 44) RECEIVE MODE button {p. 13) Display panel REDIAL/PAUSE button {pp. 14, 44) MENU button (p. 10) HELP button (p. 7) RESOLUTION button (p. 15} DIRECTORY button (pp. 26, 27} STOP button MUTE button {p. 14) Dial keypad TONE button (p. 44} STD BY button (pp. 14, 28) START/SET button (p. 10) COPY button (p. 24) Lower key key {pp. key (p. 1) FILM/PAPER SAVE key {p. 40) Direct call station keys {pp. 11.
Be tore using your unit, program the following: «Current date and time »Your logo «Your facsimile telephone number This information wilt be printed on the top or bottom of each page transmitted from your unit. Setting the date and time 1 Press (MENU]. SYSTEM SET UP Press then (D). SET DATE & TIME Enter the correct month/dayfyearhour/minute by selecting each 2 digits. Then press for AM or press () for PM. 2 3 Press (START/SET). 4 Dial keypad Example: Aug.
How to enter characters and symbols The dial keypad and the direct call stations can be used as character input keys and command keys. Pressing 0~9 and direct call station 1 will alternately select a character as shown below. Number of times Keys 1 y2 | 314l s 6|7 efe w0l AlBsiclalbo]| |2 ila ) Ikl v ikt ]s & M|NJO|lm|inlo wlx iy ilz | INSERT key (Used to insert one character or one space.} SPACE key (Used to replace one character with a space.) e DELETE key (Used to delete one character.
Setting your facsimile telephone number SYSTEM SET UP 2 Press then (@ (3. YOUR TEL NO. NGUYEN 1 Press (MENU). 3 Press (START/SET). 4 Enter your facsimile telephone number up 1o 20 digits. button inserts a space and button Dial k keypad TART/SET Press [START/SET!. Note: Logo, telephone number, date, time and page 6 Press (MENU). number will be printed outside of the document you send. To change the print position, see page 37. Adjusting volumes W Ringer volume: 3 levels (highfalutin) are available.
Selecting the receive mode This unit combines the functions of facsimile and telephone. In addition, this unit provides a TAM (Telephone Answering Machine) interface. To perform these functions, this unit has four types of receive modes; TEL/FAX, FAX, TEL and EXT. TAM. Regardless of the mode that you select, you can always place calls and send faxes. The descriptions below will pelt you understand how the unit can work for you.
Making voice calls 1 Press of lift the handset. 2 Dial a phone number. «If you misdeal, hang up and dial again. 3 ‘When the other party answers, speak into the microphone or handset. 4 When finished, press again or replace the handset, VOLUME ) REDIAL/PAUSE Dial keypad Microphone SP-PHONE To redial the last number dialed 1. Press or lift the handset. 2. Press (REDIAL/PAUSE). «if the fine is busy when using the speakerphone, the unit will automatically redial the number up o 3 times.
Transmitting documents Loading documents 1 Insert the documents FACE DOWN until a beep tone is heard. »The unit can accept up to 15 sheets of paper at a time. Adjust the document guides to the width of the documents. Press (RESOLUTION] repeatedly to the desired setting, «The selected resolution will be shown on the display. Document guides FINE: Selecting the resolution STANDARD: Suitable for printed or typewritten originals with normal-sized characters. Suitable for originals with small printing.
Transmitting documents with fewer procedure 1 Insert the documents FACE DOWN. 2 Dial a phone number, «if you misdeal, press and dial again. 3 Press (START/SET). «The unit will start to dial and transmit the documents. Note: .l there is no answer or the line is busy, the unit will Y automatically redial the number up to 3 times. To cancel redialing, press (STOP). " To send 16 or more sheets at a time Dial keypad FACE DOWN 1 | START/SET STOP Inched the first 15 sheets of the documents.
Manual reception 1 When the unit rings, press or sift the handset to answer the call. 2 When: —document reception is required, -3 Slow beep is heard, or ~-no sound is heard, press (SECRETARY. 3 Replace the handset if using it. «The unit will start reception. ‘| To stop reception halfway : { 4 (E-PHONE) | (START/SET Press (STET, (SP-PHONE) | STOP . Note: +When receiving an over-sized document, the unit wife divide it into two or more pages when printing out.
Automatic reception Set to the TERAPIXEL, FAX, or EXT. TAM mode by pressing RECEIVE MODE. When a fax call is received, the unit will automatically activate the fax function to receive documents. Caution: Do not let more than 100 sheets of 75 g/m? paper accumulate at one time on the paper cassette. This may cause a paper jam. Receiving in the TEL/FAX mode When a call is received, the unit will work as follows. A call is received.
“ Setting the TEL/FAX mode ring count You can choose from 2 to 4 told rings. -1 Press (MENU). 2 Press then press ). TEL/FAX RING Press (START/SET). COUNT=2 {AY] Press [E or[}] to select the desired number of rings. Press (START/SET). Press (MEND). Dial keypad /= Setting the silent fax recognition ring count When a fax call is received in the TEL/FAX mode, the unit will automatically activate the fax function without ringing. If the unit detects a voice call, it will ring.
) ’ 5 Press (START/SET). 1 Receiving in the FAX mode When a call is received, the unit will ring and activate the fax function. Setting the FAX mode ring count You can choose from 2 {o 4 rings. 1 Press (MENU). SYSTEM SET UP 2 Press then press FAX RING 3 Press (START/SET]. COUNT=2 (AY] 4 Press E] or 1o select the desired number of rings. Dial keypad 6 Press (MENKENT. Note: if you wish to be able to answer a call before the unit does, increase the number of rings.
Receiving in the EXT. TAM mode This mode is used only when an External Telephone Answering Machine {(EXT. TAM) has been connected to the facsimile unit. Note: When an external telephone or telephone answering machine is in use, the facsimile unit will show the following message on the display: XT. IN USE In this case, you cannot use the SP-PHONE button of the facsimile unit.
Setting up the answering machine 1. Set the desired number of rings the telephone answering machine. 2. Record a greeting message referring to the example below. “This is {your name, business and/or telephone number). We are unable to answer the phone right now. Please leave a message naffer the long beep. To send a fax, dial my remote fax activation code and start transmission. Thank you.” Do not pause for more than 4 seconds in the message. ~Your message can seconds long.
Setting the silent detection This feature allows the facsimile unit to activate the fax function automatically when a silent pause longer than 4 seconds is detected in the EXT. TAM mode. Helpful hints: «if you wish to receive documents from stations that do not send a calling tone after dialing, activate this feature. «If you use a single cassette tape to give a greeting message and to record incoming messages, deactivate this feature. 1 Press (MENU. SYSTEM SET UP 2 Press then press SILENT DETECT.
Making a copy: 1 insert the documents FACE DOWN. «The unit can make a copy sheets of paper at a time. 2 Press (COPY). #The unit will start copying. To stop copying halfway Press (STOP). »The unit will stop copying and eject the documents. Note: +Any transmittable document can be copied {see page 16). * +When copying, the unit will automatically select FINE resolution, . #You can make or receive a voice call while making a copy.
The unit's memory allows you to use both one-touch dialing and speed dialing for rapid access ta your most frequently dialed numbers, One-touch dialing: The unit is equipped with 13 direct call station keys, each of which s divided into an upper station and a lower station, Speed dialing: 2-digit numbers {00-58). Storing Tel/Fax numbers 1 Press [MENU] until the following message is displayed. STORE TEL NO. 2 For one-touch dialing: M Upper station no. 1-13 Press one of the direct call station keys.
Making voice calls using automatic dialing 1 Press {SP-PHONE) or {itt the handles. Using one-touch dialing: W Upper station no, 1-13 Press one of the direct call station keys. & Lower station no. 14-26 Press [LOWER), then press one of the direct call station keys. Using speed dialing: Press (DIRECTORY), then press and the desired 2-digit number (00-58). Speed dial stations {DIRECTORY | | (LOWER Direct call stations Transmitting documents using automatic dialing 1 Insert the documents FACE DOWN.
Electronic telephone directory The station names stored in memory will be automatically registered into the electronic telephone directory in alphabetical order. You can make a fax or voice call by selecting the desired station name on the display. if you wish 1o send a fax, insert the documents into the document feeder first. 1 Press (DIRECTORY]. Rt 2 Press the dial key in which the first initial of a station name is assigned (see index table below).
i Voice contact Initiating voice contact You can have a voice conversation with the same call after the fax message is completed. This will save the extra expense and time of making another call. important: This feature works only when the other party's unit is equipped with a voice contact feature. -1 Press (SP-PHONETIC STD BY) while transmitting or receiving documents. VOICE STANDBY «Your unit will call the other party with a distinctive ring.
Poling The polling feature allows you to receive a document from another compatible machine where you pay for the call as opposed 1o the document being sent to you, thereby saving the other party call charges. This unit can perform both receive and transmit polling. Receive polling To place a call and recover a document from another machine, follow the steps below. Make sure that no documents have been fed into your unit and that the other party's machine is ready for your cal.
Delayed transmission The unit can send fax documents automatically at a specific time. This allows you to take advantage of low-cost calling hours offered by your telephone company. Defrayed transmission can be programmed up to 24 hours in advance. 1 insert the documents FACE DOWN, Press (MENU]. SYSTEM SET UP. . Press then press (2) 8. DELAYED XMT Press (START/SET]. MODE=OFF [A Y] Press or[F] to select "ON". MODE=ON [AV] «lf this features is not required, select "OFF™, o A W Press (SECRETARY. NC.
Reserving transmission during a fax reception ‘While the unit is receiving documents, you ¢an reserve your fax transmission to another station. The unit will automatically transmit documents after fax reception is complete. 1 insert the documents FACE DOWN during fax reception. 2 Enter the phone number by using one-touch dialing, speed dialing, full number dialing or electronic telephone directory. s When using full number dialing, press START/SET). EMT RSV. ON To cancel the reservation feeder tray.
Remote fax receiving using an extension if you have an extension phone connected on the same line, it is possible to receive a fax message to your facsimile unit. Using the extension phone, dial the remote fax activation code. This saves you from going to the facsimile until and pressing (START/SET ). Important «To activate this feature, use a touch tone telephone as the extension phone. «The remote fax activation code is sett pres elected setting.
oo N W Setting the friendly reception feature When you receive a call with an extension phone handset, you may hear a slow beep. The calling party wishes to send a fax. Replace the handset on the cradle. Your facsimile unit will start fax reception automatically (Friendly Reception). This feature is activated as a per-selected setting. You can deactivated this feature by following steps below.
Junk mail prohibitory This feature prevents reception from facsimile machines whose phone numbers are not stored in automatic dialing, Important: «This feature is available when the unit is in the EXT. TAM, TEL/FAX or FAX mode. »This feature does not work under the following conditions: e-wiien manual reception is performed, or —the other party does not program their facsimile |0 number correctly.
oo N W Line mode Depending on your telephone ling connection, select either CO (Central Office) or PBX {Private Branch Exchange). CO: Your ling is connected to the central office (per-selected setting). PBX: Your ling is connected to the private branch exchange. 1 2 Press (MEND). SYSTEM SET UP LINE MODE Press (START/SET). MODE=CO (AY] Press select the desired setting. Press then Press (START/SET). Press (MENU).
Logo print position Logo, telephone number, date, time and page number will be printed on the transmitted document from your unit in the following manner. QUT: Outside of the transmitted document’s paper size (per-selected setting) IN: Inside of the transmitted document's paper size OFF: Not printed To change the setting, proceed as folios, 1 Press (MENU. SYSTEM SET UP LOGO POSITION MODE=OUT ([AY] Press or[™] to select the desired 2 Press then Press (START/SET). setting. Press (START/SET).
Overseas transmission mode You may experience difficulty in transmitting documents overseas. This feature will make sending documents easier as the transmission speed is slowed down. Press (MENU]. SYSTEM SET UP OVERSEAS MODE Press then 2)3). Press (START/SET). MODE=OFF [AV] Press or[¥] 1o select “ON". MODE=ON [AY] +If this feature is not required, select “OFF”, . Press [START/SET). Press (MENGZI. s Then start transmission procedure (see pages 15 and 18).
Copy reduction mode When you copy documents that are longer than the recording paper, the unit can reduce the original document and print it out on one page by programming a suitable reduction rate below. The reduction rate is determined by a combination of the size of recording paper and original document. @ Recommended reduction rate: Mode Size of recording paper Size of original document OFF (per-selected} Ad . A4, Letter 2% .
Receiving reduction mode When the size of the documents sent by the other party is as fare as, or larger than the recording paper, the unit can reduce each page of the document and print it out on the recording paper at a suitable reduction tale below. The reduction rate is determined by a combination of the size of the recording paper and received document.
Film/Paper save reception Use this feature if you wish to save film and recording paper when receiving two or more faxed pages. When this feature is set, the unit will reduce documents to half their length and print out two pages of documents on one page. A boundary will be printed out between the documents. important: This feature will not work when the other party sends a document in fine resolution or other nonstandard resolutions.
Extension copy Use this feature to enlarge a document to twice the length of the paper that is correctly being used in the paper cassette. This feature is used 1o reverse the film/paper save function (see page 40). Sample of extension copy: When you wish to enlarge the top half of the document: Original document Enlarged copy Top edge i Top half ABC Bottom half DEF T Insert & document into the ' unit from the top edge side FACE DOWN.
Pager alert for fax reception This feature allows your unit to call your pager automatically each time your unit receives a fax message. This feature will be only effective for automatic pager. 1 Press (MENU SYSTEM SET UP 2 Press then 7). FAX PAGER 3 Press [START/SET]. MODE=OFF (AY] 4 Press (4] or[¥] to select “ON". MODE=ON (A Y) ff this feature is not required, select HOFF, | 5 Press (SECRETARIAT Dial keypad NO.= 6 Enter your pager phone number. If necessary, press twice.
o AW 2 Press then Advanced Operations Display contrast Use this feature to adjust the brightness of the display. The following choices are available. NORMAL: setting) LIGHT: Used when the display contrast is dark. DARKER: Used when the display contrast is fight. . 1 Press (RUMMER. 2 Press (8), then LCD CONTRAST Press (START/SET). MODE=NORMAL[ A ¥) Crass [a] or[¥] to select the desired mode. Press (START/SET). Dial keypad START/SET @/E Press (MENU).
TONE button The TONE button is used when your fine has a rotary pulse dial service. Pressing the button allows you to change temporarily from pulse 1o tone mode during a dialing operation. © When you hang up, the unit will automatically return to pulse mode. R button The R button functions as the hook switch on a regular phone. it you misdeal or dial another phone number, press the R button firmly. The call will be terminated and you will hear dial tone.
Printing reports and lists You can print out the following reports lists from your unit, Feature List—provides you with the current settings of the basic and advanced programming features {see page 48). Telephone number list—provides you with phone numbers and their station names which are stored in automatic dialing. {Code in each phone number) P: A pause has been entered. F: A R has been entered. { } A secret phone number has been entered.
Setting the transmission report printing One of the following choices is available. ERROR: The transmission report will print cut only when the fax transmission fails. ON: The report will always print out, indicating whether fax transmission is successful or not. OFF: The report will not print (per-selected setting}. 1 Press (MEND). SYSTEM SET UP Press then @F). TX-REPORT MODE Press [START/SET]. MODE=OFF [AY] Press or[¥] to select the desired mode. Press (SECRETARIAT. Press (MENU).
Sample of journal report Jan. 25 1996 05:22PM NO, DITHER FACSIMILE START TIME PAGES RESULT & CODE ol 1234587 Jan. 9998765 Jan, 2 CR 631 22333455 Jan. o1 oK 04 ERROR (43} 05 +387.% Sample of transmission report o3 COMMUNICATION 93 ¥ | Error code Communication {for service result (see below} personnel use only) Err R e NO. GATHER FACSIMILE 01 COMPANY RBC gan. START TIME USAGE PAGES 'RESULT Sen.
Summary of user programmable features Basic features Code Feature Selection initial setting Page #01 |SET DATE & TIME mm/ddfyy him 12:00 AM} 10 #02 YOUR LOGO {Panasonic FAX SYSTEM) 10 #03 | YOUR TELEPHONE NUMBER 12 ) #04 |PRINT TRANSMISSION REPORT ERROR/ON/OFF OFF 46 #06 | TEL FAX DELAYED RING 2/3/4 rings 2 rings 18 #07 |FAX RING COUNT 2/3/4 rings 2 rings 20 #11 |REMOTE TAM ACTIVATION ON/OFF OFFD=11 22 Advanced features .
Error messages on the display If the unit detects a problem, one of the following messages will appear on the display. CAUSE & REMEDY .. : «The recording paper is jammed near the paper cassette. Clear the jammed paper (see page 53). «The top cover is open. Close it «The document is not fed into the unit properly. Reinsert the document and try again. If feeding occurs frequently, clean the feeder rollers (see page 55}. if the problem remains, adjust the feeder pressure (see page 54).
Before requesting help General ‘CAUSE & REMEDY i 1 cannot make and receive calls. +The power cord or telephone line cord is not connected. Confirm the connection (see page 7). The unit does not work. #Disconnect the unit from the telephone ding and connect 1o a known working phone. If the known working phone operates properly, call your service personnel to have the unit repaired. If the known working phone does not operate properly, consult your telephone company. The unit does not ring.
CAUSE & REMEDY Recording image is faint. clearer copy of the document. «The thermal head is dirty. Clean it {see page 55). «The sender transmitted a faint document. Request them to transmit a A blank sheet is ejected after the received documents are printed out. «The receiving reduction rate is not programmed correctly. Program the proper reduction rate (see page 38). Operation in EXT. TAM mode 1 cannot receive documents automatically. +Your greeting message on the answering machine is too long.
Clearing a recording paper jam If a recording paper jams, the display will show one of two messages below. Remove the jammed recording paper hollowing either message. CHECK CASSETTE PAPER JAMMED Removing a jammed recording paper near the head unit 52 1 A recording paper jammed near the head unit. A retarding paper jammed near the paper cassette. Open the top cover. Press the green button on the right marked “PUSH" and lift up the head unit. Remove the film cartridge.
9 Removing a jammed recording paper near the paper cassette 1 Press the head unit down firmly until # clicks into place. Close the top cover securely by pushing down on both sides. insert the paper cassette into the unit until it clicks into place. Lott up the paper cassette slightly and pull it towards you to remove it Reach into the paper cassette opening and remove the jammed recording paper. «When the jammed paper cannot be removed easily, open the top cover and head unit, and remove the jammed paper.
Clearing a document jam I the unit does not release an original document during feeding, remove it as shown below. Front lid Front lid open lever Adjusting the feeder pressure 1 2 Slide the front lid open lever towards you to open the front {id. Remove the jammed document carefully, Close the lid securely by pushing down on both sides. #f ministering of documents occurs frequently, adjust the feeder pressure. Front lid open lever 54 1 2 Slide the front lid open lever towards you to open the front lid.
Cleaning the unit Cleaning the document feeder unit I ministering occurs frequently or dirty pasterns or black bands appear on a copied or transmitted document, clean the feeder rollers, sub roster, rubber flap, white plate and glass. Sub rifler | White plate ] Rubber flap Feeder rollers Glass Front d open lever Cleaning the thermal head Disconnect the power cord and the telephone ling cord. Slide the front lid open lever towards you to open the front lid.
Replacing the film or film cartridge When the unit detects the end of the film, the following message will be displayed. FILM EMPTY Replace the film or film cartridge with a new one. To order a replacement part, see page 59, 56 1 Open the top cover. Press the green button on the right marked “PUSH" and sift up the head unit. Take out the film cartridge. «If you purchased a film cartridge (Mendel no. KX-FA132X) for replacement, skip to step 11, +To replace Monty the film, go to step 4.
Bite leader opting and Routine Car e RIS Insert the film into the cartridge so that the arrow on the open cartridge points in the same direction as the arrows on the film, »lf you insert a film which was used hallway, insert the unused spool of the film on the “FILM SUPPLY" mark of the cartridge. insert the firm cores correctly Incorrect fertilizing 1o the prostration 1o me Co Est right. Roll the bite leader of the film by winding the gears of the core until the leader is no longer visible.
When using this product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked an this product. 3. Unplug this product from wall outlets before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.. 4.
Important safety instructions (co refined ) INSTALLATION: 1. Never install telephone wiring during a lightning storm, 2. Never install telephone jacks in wet locations unless the jack is specifically designed for wat {ovations. 3. Never touch uninitiated telephone wires or terminals unless the telephone fine has been disconnected at the network interface. 4.
Accessory order information Use the following for replacement. Problems will scour if other brands of films are used. Model No. Description Comment KX-FA132X Film cartridge 1 cartridge & 1 film: 216 mm x 200 m ROFL KX-FA133X Replacement film (1 set) 216 mm x 200 m roll ops . Specifications wham © o~ Applicable Lines: Document Size: Effective Scanning Width: Recording Paper Size: Effective Printing Width: Transmission Time*: Fax Auto Redial: . Telephone Auto Redial: . Scanning Density: . Halftone Level: .
REGIE VAN TELEGRAFIE DIENSTAANWIWZINGEN EN TELEFONIE Telefaxnummer Houder van het telefoonabonnementen E Nieuwe aanstuiving D Verhuizing Tekstwijziging D ) Verandering NA{™] Tex NA . Volgnummer : . Dalm. OFFICIËLE TELEFAXGIDS Ondergetekende {naam en voornaam of maatschappelijke benaming)' houder van de telefooninstallatie waarop een teelfaxtoestel is aangesp koten, heeft kennis genomen van de ommestaande bepalingen en wenst als volgt m wens? niet D te worden opgenomen in de officie e telefaxgids. 1.
GEDETAILLEERDE INLICHTINGEN INZAKE DE VERMELDINGEN IN DE OFFICIËLE TELEFAXGIDS 1. Kosteloze vermelding Voor elk telefaxnummer dat de abonnee in de gids laat vermeiden, heeft hij recht op een gratis inlassing. De kosteloze vermelding bestaat uit standaardgegevens en eventueel supplementair een gratis informatief gegeven: A. Standaardgegevens 1.1, de naam die de alfabetische rangschikking bepaalt. Voor particulieren is dit de familienaam en de initiaal van de voornaam.
Index Automatic dialing .ureoreninonnsrnes 25, 26 Copy reduction mode Date and time .. Delayed transmission DELETE key 11 Dialing mode .7 Direct call station keys 11, 25,26 DIRECTORY button Display contrast Electronic telephone directory 27 Error messages Extension copy EXT. TAM mode FAX mode FAX ring count 20 Feeder pressure . 54 FILM/PAPER SAVE key Friendly reception HELP button... INSERT K&Y e 11 Journal auto print Journal report Junk mail prohibitory Line mode Logo position LOWER key MENU button .
Panasonic Quick Reference Guide KX-F1000BL Please read the operating instructions completely before using your unit. This guide will help you initiate use of your fax unit, Keep this guide near your unit for easy reference. M Film cartridge Toy v P cobs Tray fin Document /Riot Holder feeder tray 1 Open the top cover, 3 insert the cartridge. inset the three tray fins into the 2 Pressthegreenbuttononthe 4 Close the head unit and the slots of the unit. Then press right marked “PUSH" and fight up top cover.
FACE DOWN {up to 15 sheets) DIRECTORY 2-digit number for speed dealer Direct call stations SP-PHONE START/SET i Manual transmission 1 Insert the documents FACE DOWN. 2 Press SP-PHONE or fight the handset. 3 Dial a phone number.4 When a fax tone is heard, press START/SET, § Replace the handset if using it. Automatic transmission For storing pane numbers into memory, see the operating instructions. 1 Insert the documents FACE DOWN. 2 W Using one-touch dialing: Upper station no.