Installation Guide Home Network System Outdoor Camera Model No. KX-HNC600 Thank you for purchasing a Panasonic product. This document explains how to install the outdoor camera properly. For details about how to use the system, refer to the User’s Guide (page 26). Please read this document before using the unit and save it for future reference. For assistance, visit our Web site: www.panasonic.com/support for customers in the U.S.A. or Puerto Rico. Please register your product: www.panasonic.
Table of Contents Introduction Accessory information ..................................3 Important Information About this system .........................................4 For your safety .............................................4 Important safety instructions ........................5 For best performance ...................................5 Privacy and rights of portrait ........................6 Other information .........................................
Introduction Accessory information Supplied accessories No.
Important Information About this system This system is an auxiliary system; it is not designed to provide complete protection from property loss. Panasonic will not be held responsible in the event that property loss occurs while this system is in operation. For your safety To prevent severe injury and loss of life/ property, read this section carefully before using the product to ensure proper and safe operation of your product. WARNING Power connection R Use only the power source marked on the product.
Important Information Medical R Consult the manufacturer of any personal medical devices, such as pacemakers or hearing aids, to determine if they are adequately shielded from external RF (radio frequency) energy. DECT features operate between 1.92 GHz and 1.93 GHz with a peak transmission power of 115 mW. R Do not use the product in health care facilities if any regulations posted in the area instruct you not to do so.
Important Information R Do not expose this product to direct sunlight or other forms of powerful light such as halogen lights for long periods of time. (This may damage the image sensor.) R Do not place heavy objects on top of the product. R When you leave the product unused for a long period of time, unplug the product from the power outlet. R The product should be kept away from heat sources such as heaters, kitchen stoves, etc.
Important Information Notice For assistance, please visit www.panasonic.
Installation Location Wireless communication range The wireless communication range of each device in the system from the hub is approximately 50 m (160 feet) indoors and approximately 300 m (1,000 feet) outdoors. Wireless communication may be unreliable when the following obstacles are located between the hub and other devices.
Installation Location Detection range Visual sensor Infrared sensor Can detect motion anywhere in the visible image. Can detect motion only in part of the visible image (shown here in gray) R You can adjust the area detectable by the visual sensor. For more information, refer to the User’s Guide (page 26). R You can adjust the area detectable by the infrared sensor. See “Adjusting the infrared sensor range”, page 22. R Detection does not occur when there are obstacles in front of the infrared sensor.
Installation Location Direction of motion It is easier to detect objects that move sideways in front of the camera, and more difficult to detect objects that move directly toward the front of the camera. A B C D A It is difficult to detect movement directly towards the front of the camera. B It is easy to detect movement sideways in front of the camera. C Detection range D Camera 10 For assistance, please visit www.panasonic.
Installation Location Installation location examples I want to detect visitors approaching the house Refer to the table below for detecting visitors at an entrance or gate without detecting cars in the street. Ideal example Poor example 1 1 Approx. 3 m (9.8 feet) Visitors pass in front of the camera from side to side, cars in the street are less likely to cause false detections. Cars in the street are more likely to cause false detections. For assistance, please visit www.panasonic.
Installation Location I want to detect people entering the garage Refer to the table below for detecting people entering a garage without detecting cars in the street. Ideal example Poor example Visitors pass in front of the camera from side to side, cars in the street are less likely to cause false detections. R To prevent faces from being obscured by tall vehicles, adjust the installation position and angle of the camera. 12 Cars in the street are more likely to cause false detections.
Installation Location Do not install in these locations Installing in the following areas may cause deformation, discoloration, malfunction, or operational failure R In direct sunlight or directly under an outdoor light (even if the surroundings are within operational temperature range, parts of the product may become hot) R Areas subject to frequent vibration, shock, or impact R Near fire, heating devices, magnetic fields (such as near magnets), or air conditioners (including outdoor equipment such as uni
Installation Location R Areas affected by breezes from fans, air conditioning unit compressors, water heaters, or car exhaust (severe temperature variations may cause false detections) R Areas with strong winds (wind can shake the camera and cause false motion detection) R Areas with reflective objects, such as glass, that can interfere with detection of temperature variation R Areas where brightness changes easily (such as areas where shadows form in the afternoon and lights turn on at night) R Areas wher
Setup Part names and functions H G I Indicator Status Red, blinking Live images are being viewed or recorded Red, blinking quickly Camera is out of range of the hub, or device malfunction Amber, blinking Camera is not registered to a hub *1 J A B CD E You can configure the camera so that its LED indicator does not light during normal operation. For more information, refer to the User’s Guide (page 26).
Setup Registering the camera This procedure is not required for devices that were included as part of a bundle. Before you can use the camera, it must be registered to the hub. If the camera is not registered to a hub, the camera’s LED indicator blinks in amber. You can register each device by using the registration buttons or the [Home Network] app. Note: R Before registering the camera, make sure the AC adaptors of the hub and camera are connected and each device is powered.
Setup Installation Installation precautions R Do not install the camera on a ceiling. R Do not install the camera in areas directly exposed to water or rain. R Holes must be made in the wall for cables and wires to pass through. Panasonic takes no responsibility for issues related to opening holes in walls. R Make sure to waterproof the holes you make in the wall. R Make sure you attach the safety wire to prevent the camera from falling. R Do not use an impact driver.
Setup Ideal example Structure supports exterior surface 4 2 Insert the screw and tighten it. 2 2 Camera mounting stand ALC (autoclaved lightweight cellular concrete) 1 1 Siding 2 Structure behind siding Concrete R Do not use the included screws. Use screw anchors (screw ø: 4 mm (5/32 inches)) designed for concrete walls. R Carefully read the instructions supplied with the anchors. Follow instructions regarding drill bit diameter, hole depth, etc. R Drill a pilot hole.
Setup Installing the camera 1 Attach the safety wire to the camera. R Place the ring of the safety wire (A) over the screw hole. R Place a washer (B) on top of the ring of the safety wire. R Tighten the screw (C) for the safety wire on top of the washer. Note: R Use the following template below when determining the location of the screw holes. 37 mm (1 15/32 pulgadas) 37 mm (1 15/32 pulgadas) 3 2 2 1 Attach the camera mounting stand to an outdoor wall.
Setup 3 Attach the camera to the stand. R Loosen the screw (1). R Insert the tip of the stand (A) into the stand attachment hole (B) on the rear or bottom side. R Secure the camera by tightening the screw (2). Attaching to the hole on the rear side 2 1 1 4 Adjust the camera angle. R Loosen the screw (A), adjust the camera to the desired angle, and then tighten the screw (B) to secure the camera in place. 1 2 2 Attaching to the hole on the bottom side 2 1 1 2 20 For assistance, please visit www.
Setup 5 Attach the safety wire to the wall. R Place the ring of the safety wire (A) on the wall. R Place the washer (B) on top of the ring of the safety wire. R Tighten the screw (C) for the safety wire on top of the washer. 3 2 1 6 Connect the DC cable to the AC adaptor. R Pull the DC cable indoors, and connect the DC cable plug (A) to the AC adaptor plug (B). R Connect the AC adaptor (C) to the power outlet. 1 Outdoors 2 Indoors 1 2 1 2 3 Note: R Attach the safety wire while it is bent.
Appendix Testing the motion detection range Adjusting the infrared sensor range After you have installed the [Home Network] app on your mobile device, you can use your mobile device to test the performance of the camera’s motion detection features. For details about these operations, refer to the User’s Guide (page 26). If there are objects that you do not want the infrared sensor to detect, you can adjust the detectable area by attaching sensor range caps.
Appendix Situation and cap types When you want both sides of the camera to be detectable Standard cap (attached to the camera) When you want one side to be undetectable Cap 1 Approximate detection range (view when looking from above) *1 20 °C (68 °F) 0 °C (32 °F) 1 Cap 3 2 6 m (19.7 feet) 3 4 m (13.1 feet) (Example) Cap 1 (Example) Cap 1 (Example) Cap 1 1 5 m (16.4 feet) 2 6 m (19.7 feet) 3 4 m (13.1 feet) (Example) Cap 3 (Example) Cap 3 3 2 1 5 m (16.4 feet) 2 6 m (19.7 feet) 3 4 m (13.
Appendix About the attachment angle of the sensor range cap Example 1 When there is an object on the right side of the viewable area that you do not want to be detected (such as trees): Attach one of caps 1-3 as shown in the example (1) according to the area you do not want to be detected. Example 2 When there is an object on the top left of the viewable area that you do not want to be detected (cars in a street, etc.
Appendix Replacing sensor range caps 1 Remove the attached standard cap. 2 Remove the desired sensor range cap from one of the 4 types (A) and attach it to the sensor (B). R When attaching, rotate the tab (1) on the cap toward the top or at a 45-degree angle according to the type of cap or direction, and attach the cap on the camera, shown in the following illustration. 1 1 2 For assistance, please visit www.panasonic.
Appendix Features available when using the [Home Network] app Accessing the User’s Guide Some of the camera’s features that are available when using the [Home Network] app are listed below. For more information, refer to the User’s Guide (page 26). – Security system You can use the app to arm and disarm the security system, confirm the current status of the sensor, and view a log of previous security events. – Live camera monitoring You can view live images from the camera, even while away from home.
Appendix Specifications R Standards DECT 6.0 (Digital Enhanced Cordless Telecommunications 6.0) R Frequency range DECT: 1.92 GHz – 1.93 GHz R RF transmission power DECT: 115 mW (max.) R Power source 120 V AC, 60 Hz R Power consumption Standby: 1.4 W During operation: 1.5 W (when the LED lights are not lit) 2.3 W (when the LED lights are lit) R Operating conditions -20 °C – 50 °C (-4 °F – 122°F) up to 90% relative humidity (non-condensing) R Transmitting range Approx. 50 m (160 feet) indoors Approx.
Appendix FCC and other information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Privacy of communications may not be ensured when using this phone.
Appendix Customer services Customer Services Directory (United States and Puerto Rico) Obtain Product Information and Operating Assistance; locate your nearest Dealer or Service Center; purchase Parts and Accessories; or make Customer Service and Literature requests by visiting our Web Site at: www.panasonic.com/support or, contact us via the web at: www.panasonic.
Appendix Warranty (For United States and Puerto Rico) Panasonic Home Network System Products Limited Warranty Limited Warranty Coverage If your product does not work properly because of a defect in materials or workmanship, Panasonic Corporation of North America (referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (“Limited Warranty period”), at its option either (a) repair your product with new or refurbished par
Appendix Limited Warranty Limits And Exclusions This Limited Warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage.
IMPORTANT! If your product is not working properly. . . A Reconnect the AC adaptor to the camera. B Use the Home Network app to access the User’s Guide and refer to the Troubleshooting section. Visit our Web site: www.panasonic.com/support • FAQ and troubleshooting hints are available. For your future reference We recommend keeping a record of the following information to assist with any repair under warranty. Serial No.
Guía de instalación Sistema de red doméstico Cámara exterior Modelo n° KX-HNC600 Gracias por adquirir un producto Panasonic. Este documento explica cómo instalar la cámara exterior de forma correcta. Para obtener detalles sobre cómo usar el sistema, consulte la Guía del usuario (página 21). Lea este documento antes de usar la unidad, y guárdelo para consultarlo en el futuro. Para obtener ayuda, visite nuestro sitio web: www.panasonic.com/support para clientes en los EE. UU. o Puerto Rico (solo en inglés).
Tabla de Contenido Ubicación de la instalación Alcance de la comunicación inalámbrica .............3 Información acerca de las características del sensor ..................................................................3 Ejemplos de ubicaciones para instalación ...........6 No instale en las ubicaciones siguientes .............8 Configuración Nombres de los componentes y funciones ........10 Led indicador ......................................................10 Resumen de configuración ...................
Ubicación de la instalación Alcance de la comunicación inalámbrica El alcance de la comunicación inalámbrica de cada dispositivo en el sistema del hub es de aproximadamente 50 m (160 pies) en interiores y de aproximadamente 300 m (1,000 pies) en el exterior. Es posible que la comunicación inalámbrica no sea tan confiable cuando se encuentran los obstáculos siguientes entre el hub y otros dispositivos.
Ubicación de la instalación Alcance de detección Sensor visual Sensor infrarrojo Puede detectar el movimiento en cualquier parte de la imagen visible. Puede detectar el movimiento solo en la parte de la imagen visible (se muestra aquí en gris) R Puede ajustar el área detectable mediante el sensor visual. Para obtener más información, consulte la Guía del usuario (página 21). R Puede ajustar el área detectable mediante el sensor infrarrojo. Consulte “Ajuste del alcance del sensor infrarrojo”, página 17.
Ubicación de la instalación Dirección del movimiento Es más fácil detectar objetos que se mueven de lado frente a la cámara y es más difícil detectar objetos que se mueven de frente hacia la cámara. A B C D A Es difícil detectar movimiento directamente hacia la parte delantera de la cámara. B Es fácil detectar movimiento lateral frente de la cámara. C Alcance de detección D Cámara Para obtener ayuda, visite www.panasonic.
Ubicación de la instalación Ejemplos de ubicaciones para instalación Quiero detectar a los visitantes que se acerquen a la casa Consulte la tabla siguiente para detectar a los visitantes en la entrada o puerta sin detectar los vehículos de la calle. Ejemplo ideal Mal ejemplo 1 1 Aprox. 3 m (9.8 pies) Los visitantes pasan en frente de la cámara de lado a lado, y es poco probable que los vehículos en la calle generen detecciones falsas.
Ubicación de la instalación Quiero detectar a las personas que ingresen al garaje Consulte la tabla siguiente para detectar a las personas que ingresen al garaje sin detectar los vehículos de la calle. Ejemplo ideal Mal ejemplo Los visitantes pasan en frente de la cámara de lado a lado, y es poco probable que los vehículos en la calle generen detecciones falsas. R Para evitar que los vehículos altos oscurezcan los rostros, ajuste la posición de instalación y el ángulo de la cámara.
Ubicación de la instalación No instale en las ubicaciones siguientes Si se instala en las áreas siguientes puede provocar deformación, falta de color, errores o fallas de operación R A la luz del sol o bajo una luz exterior (incluso si el entorno está dentro del rango de temperatura funcional, es posible que algunas partes del producto se calienten) R Áreas sujetas a vibraciones, golpes o impactos frecuentemente R Cerca del fuego, calefactores, campos magnéticos (como cerca de imanes) o aires acondicionado
Ubicación de la instalación R Áreas afectadas por brisas de ventiladores, unidades compresoras de aires acondicionados, calentadores de agua o caños de escape de vehículos (es posible que las variaciones fuertes de temperatura generen detecciones falsas) R Áreas con vientos fuertes (el viento puede sacudir la cámara y generar detecciones de movimiento falsas) R Áreas con objetos reflectivos, como vidrios, que pueden interferir con la detección de la variación de temperatura R Áreas donde el brillo cambia c
Configuración Nombres de los componentes y funciones H G Indicador Estado Rojo, parpadeante Las imágenes se están visualizando o grabando Rojo, parpadeo rápido La cámara está fuera de alcance del hub o falla el dispositivo Ámbar, parpadeante La cámara no está registrada en el hub *1 I J Puede configurar la cámara de forma tal que el Led indicador no se encienda durante el funcionamiento normal. Para obtener más información, consulte la Guía del usuario (página 21).
Configuración Cómo registrar la cámara Este procedimiento no es necesario para unidades que son parte de un paquete. Antes de que pueda usar la cámara, se debe registrar en el hub. Si la cámara no se ha registrado a un hub, el indicador Led de la cámara parpadea en ámbar. Puede registrar cada unidad mediante los botones de registro o la aplicación [Red doméstico].
Configuración Instalación Información sobre el material de instalación Precauciones de instalación Revestimiento R No instale la cámara en un techo. R No instale la cámara en áreas expuestas de forma directa al agua o a la lluvia. R Se deben hacer orificios en la pared para que pasen los cables. Panasonic no asume ninguna responsabilidad ante problemas relacionados por abrir orificios en paredes. R Asegúrese de proteger los orificios que haga en la pared contra el agua.
Configuración Ejemplo ideal La estructura sustenta la superficie exterior 4 2 Introduzca el tornillo y ajústelo. 2 2 Soporte de montaje de la cámara ALC (concreto celular ligero en autoclave) 1 1 Revestimiento 2 Estructura detrás del revestimiento Concreto R No use los tornillos incluidos. Use los taquetes (tornillos de ø: 4 mm (5/32 pulgadas)) diseñados para paredes de concreto. R Lea con atención las instrucciones suministradas con los taquetes.
Configuración Nota: R Utilice la siguiente plantilla cuando determine la ubicación de los orificios de los tornillos. Cómo instalar la cámara 1 Coloque el cable de seguridad en la cámara. R Coloque la terminal circular del cable de seguridad (A) sobre el agujero para el tornillo. R Coloque una arandela (B) encima de la terminal circular del cable de seguridad. R Ajuste el tornillo del cable de seguridad (C) encima de la arandela.
Configuración Colocación en el orificio en la parte inferior 2 1 1 4 2 Ajuste el ángulo de la cámara. R Afloje el tornillo (A), ajuste la cámara al ángulo deseado y luego ajuste el tornillo (B) para asegurar la cámara. 1 5 Coloque el cable de seguridad en la pared. R Coloque la terminal circular del cable de seguridad (A) sobre la pared. R Coloque la arandela (B) encima de la terminal circular del cable de seguridad. R Ajuste el tornillo del cable de seguridad (C) encima de la arandela.
Configuración 6 Conecte el cable de CC al adaptador de corriente. R Hale el cable de CC interior y conecte el enchufe de cable de CC (A) al enchufe del adaptador de corriente (B). R Conecte el adaptador de corriente (C) a la toma de corriente. 1 Exterior 2 Interior 1 2 1 2 3 Nota: R Use solo el adaptador de corriente alterna Panasonic PNLV236 que se suministra. R Asegúrese de conectar el enchufe del cable de CC y el enchufe del adaptador de corriente interiores.
Apéndice Cómo probar el alcance de detección de movimiento Ajuste del alcance del sensor infrarrojo Después de instalar la aplicación de [Red doméstico] en su dispositivo móvil, puede usarlo para probar el funcionamiento de las características de detección de movimiento de la cámara. Para obtener más detalles sobre estas operaciones, consulte la Guía del usuario (página 21).
Apéndice Situación y tipos de tapas Cuando desea que se detecten ambos lados de la cámara Tapa estándar (colocada en la cámara) Cuando desea que se detecte solo un lado Tapa 1 Alcance de detección aproximado (vista desde arriba) *1 20 °C (68 °F) 0 °C (32 °F) 1 30 °C (86 °F) 3 2 1 5 m (16.4 pies) 2 6 m (19.7 pies) 3 4 m (13.1 pies) (Ejemplo) Tapa 1 (Ejemplo) Tapa 1 (Ejemplo) Tapa 1 1 3 2 Tapa 2 1 5 m (16.4 pies) 2 6 m (19.7 pies) 3 4 m (13.
Apéndice Acerca del ángulo de colocación de la tapa de alcance del sensor Ejemplo 1 Cuando hay un objeto en el lado derecho del área visible que no quiere que se detecte, (como árboles): Coloque una de las tapas 1-3 como se muestra en el ejemplo (1) de acuerdo con el área que no desea que se detecte. Ejemplo 2 Cuando hay un objeto en el extremo superior izquierdo del área visible que no desea que se detecte (vehículos en la calle, etc.
Apéndice Reemplazo de las tapas de alcance del sensor 1 Extraiga la tapa estándar ya colocada. 2 Retire la tapa de alcance del sensor deseado de uno de los 4 tipos (A) y colóquelo en el sensor (B). R Al instalar, gire la pestaña (1) en la tapa hacia arriba o a un ángulo de 45-grados de acuerdo con el tipo de tapa o dirección y coloque la tapa de la cámara, como se muestra en la siguiente ilustración. 1 1 2 20 Para obtener ayuda, visite www.panasonic.
Apéndice Acceso a la Guía del usuario La Guía del usuario es una colección de documentación en línea que lo ayuda a aprovechar al máximo la aplicación [Red doméstico]. 1 iPhone®/iPad® Toque en la pantalla de inicio de la aplicación. Dispositivos Android™ Toque u oprima el botón menú de su dispositivo en la pantalla de inicio de la aplicación. 2 Toque [Guía del usuario]. Nota: R También puede acceder a la Guía del usuario mediante la página web a continuación. www.panasonic.
Notas 22
Notas 23
Notas 24