Datasheet

ManualsBrandsPanasonic ManualsAutomationPreset Counter, 8 Digits, ... 24VDC

LC2H

FEATURES

1. Preset function equipped in half size

(24 × 48 mm 0.945 × 1.890 inch).

2. Display has backlight for instant

recognition.

3. 8.7 mm 0.343 inch Character Height

(previously 7 mm 0.276 inch)

Easy-to read character height increased

from 7 mm to 8.7 mm 0.276 inch to 0.343

inch.

4. Plenty of Digits

5. Counting Speed Switchable between

30 Hz and 5 kHz

6. Conforms to IP66 Protective

Construction (Front panel surface)

Weatherprooﬁng supported by using

optional mounting frame and rubber

gasket

7. Includes reassuring lock mode and

lock switch to prevent erroneous

operation.

8. Screw terminals are constructed to

protect ﬁngers to ensure safety.

9. Complies with CE marking.

Green or (Red)

(backlight)

Red or (Green)

(backlight)

Red or (Green)

(backlight)

(Lit or Flashing)

Counting upCounting

Green or Red can

be selected at setup.

Lit or Flashing can

be selected at setup.

8.7mm

.343inch

8 digits

PRODUCT TYPES

Note: Mounting frame and rubber gasket are not included.

No. digits Counting speed Output mode Output Operating voltage Part No.

8 digits

30 Hz/5 kHz

switchable

• Maintain output/hold count

• Maintain output/over count

• One shot/over count

• One shot/recount

Transistor (1a) 24 V DC LC2HP-FEW-B-DC24V

Options

Mounting frame

Use for waterprooﬁng (front panel surface)

ATH3803

Rubber gasket ATH3804

LC2H

Counters

PRESET

COUNTER

LC2H_Preset.fm Seite 79 Donnerstag, 24. Juni 2004 3:31 15

07/2004

Summary of content (7 pages)

PAGE 1
LC2H_Preset.fm Seite 79 Donnerstag, 24. Juni 2004 3:31 15 LC2H LC2H Counters PRESET COUNTER FEATURES 1. Preset function equipped in half size (24 × 48 mm 0.945 × 1.890 inch). 2. Display has backlight for instant recognition. Counting Counting up 3. 8.7 mm 0.343 inch Character Height (previously 7 mm 0.276 inch) Easy-to read character height increased from 7 mm to 8.7 mm 0.276 inch to 0.343 inch. Red or (Green) (backlight) Green or (Red) (backlight) Green or Red can be selected at setup. 8.7mm .
PAGE 2
LC2H_Preset.fm Seite 80 Donnerstag, 24. Juni 2004 3:31 15 LC2H SPECIFICATIONS Item Rated operating voltage Rated power consumption Rated control capacity Input mode Max.
PAGE 3
LC2H_Preset.fm Seite 81 Freitag, 11. Juni 2004 9:34 09 LC2H Dimensions mm inch General tolerance: ±1.0 ±.039 • External dimensions 44.8 1.764 54.4 2.142 10.4 .409 44 1.732 5 .197 48 1.890 LC2H COUNTER 22 .866 RESET MODE SET 24 .945 7 .276 • Panel cut out dimensions • When installing repeatedly (sealed installation) (Only installation frame type) The standard panel cut out is shown below. Use the mounting bracket (ATH3803) and the rubber gasket (ATH3804). (Only installation frame type) 22.
PAGE 4
LC2H_Preset.fm Seite 82 Freitag, 11. Juni 2004 9:34 09 LC2H 4. Input setting mode This is the mode for setting addition or subtraction. + Press the SET key while pressing the MODE key. Addition Subtraction 1) Pressing the SET key three times while holding down the MODE key takes you to the input setting mode. 2) The display after entering the input setting mode reads “ UP” (initial setting).
PAGE 5
LC2H_Preset.fm Seite 83 Donnerstag, 24. Juni 2004 3:31 15 LC2H OPERATION MODE Output mode Operation Example when input mode is either addition or Subject:ubtraction Output control is maintained after count-up completion and until resetting. During that time, the count display does not change from that at count-up completion.
PAGE 6
LC2H_Preset.fm Seite 84 Donnerstag, 24. Juni 2004 3:31 15 LC2H PRECAUTIONS IN USING THE LC2H SERIES CAUTIONS FOR USE 1. Insulation sheet Before using a panel mounting type, please pull and remove the insulation sheet from the side of the product in the direction of the arrow. In consideration that the product might be stored for long periods without being used, an insulation sheet is inserted before shipping. Remove the insulation sheet and press the front reset button.
PAGE 7
LC2H_Preset.fm Seite 85 Freitag, 11. Juni 2004 9:34 09 LC2H For LC2H total counter (installation frame type) (1) Remove the battery cover from the case. (2) Remove the battery from the side of the case. The battery will come loose if you put the battery side face down and lightly shake the unit. (3) Before inserting wipe clean the surface of the new battery. (4) Insert the new battery with the “+” and “–” sides in the proper position. (5) After replacing the battery, return the battery cover to the case.