Panasonic Operating Instructions Commercial Microwave Ovens Model No. NE-1054F NE-1024F NE-1022F | For microwave oven safety reference, pleas visit FDA's web page at: ’ HTTP: | I protactinium © | Before operating this oven, please read these instructions completely.
TABLE OF CONTENTS PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY IMPORTANT SAFETY INSTRUCTIONS .. Installation and Grounding Instructions. Safety Precautions How Does the Microwave Work? Outline Diagram ) How to Operate Outline Diagram (NE-1054F) How to Operate (NE-1054F) Before Operating... Heating A. Manual Single Stage Heating... B. Manual 2 or 3 Stage Heating C. Programmed Heating.. Programming A. Programming Memory Pads for Single Stage Heating B.
IMPORTANT SAFETY INSTRUCTIONS Your microwave oven is 8 cooking device and you should Use as much cars as you use with a stove or any either cooking device. When using this electric appliance, basic safety precautions should be followed, including the following: WAR reduce the risk of burns, electric shock, fire, injury to persons or exposure to excessive microwave energy: 8 , 1. Read all instructions before using the appliance. 2.
Examine Your Oven Unpack oven, remove all packing material, and examine the oven for any damage such as dents, broken door latches or cracks in the door. Notify dealer immediately if oven is damaged, DO NOT install if oven is damaged, Remove Protective Plastic Film If a plastic film has been wrapped around the oven to protect the painted finish from scratching during shipping, please remove this plastic film prior to using the oven. (However, all ovens do not have plastic film wrapping.) Placement of Oven .
General Use 1. DO NOT tamper with or make any adjustments or repairs to door, control panel housing, safety interlock switches or any other part of the oven. Do NOT remove outer pans from oven, Repairs should only be done by a qualified service person, ” DO NOT operate the oven if empty, The microwave energy will reflect continuously. throughout the oven causing overheating, if no food or water is present to absorb energy.
Microwaves are a form of high frequency radio waves similar to those used bya radio including AM; FM-and CB. They are, however, much shorter than radio waves; approximately five inches long. Electricity is converted into microwave energy by the magneto tubs. From the magneto tube, microwave energy Is transmitted and absorbed. Reflection Microwaves are reflected by metal just as a ball is bounced off a wall.
coking THE D Timer @ Control Panel ® Door Safety Lock System Rita Pastry platoon 2m Sandwich 1 Large Brandie 1 Hamburger 00.200 Burr Friar 10-146 1 Cup of Soup (lew) T0180 Bowl Clearance 10-2390 Lag Cameraman 500-630 Amazement Bre Ware et © Oven Window ® Oven Lamp © Splash Guard/Light Diffuse | circuit. » Open the door. PLACE CONTAINER OF FOOD in the oven, 3. CLOSE THE DOOR securely. 4. SET A DESIRED HEATING TIME. » MICROWAVE HEATING BEGINS. Oven light turns on. 5.
NE-1054F Control Panel NE-1054F MANUAL OPERATION azz) (10) ay) a2) Digital Display Window (see below) Memory Pads Power Level Selector Pad PRIG. Pad STOP/RESET Pad DOUBLE QUANTITY (x2) Pad START Pad Control Panel Door Safety Lock System Oven Window with Heat Vapor Film {Do Nut Remove) Oven Lamp Splash Guard/Light Diffuse on © (8) Digital Display Window Indicator Locations HIRAM MED LOW DEF HOLD . . POWER LEVEL A SPROG Indicator .
Before Operating Make sure the oven is connected to a properly grounded electrical outlet. When the door is closed, the Display Window is still blank. When the door is opened, the Display Window shows “0°, For the detail operation, see the page on each feature. This oven is preset at the factory for the following: 1. Memory Pads are preset to High Power for the indicated heating times for single stage heating. 1-10 sec. 6-1 min. 30 sec. 2-20 sec. 7 —2 min, 3-30 sec. 8 —2 min. 30 sec. . 4-45 sec. 9-3 min.
0 HEATING Open the door and place food in the oven cavity. Close the door. “0” must be showing in the Display Window. A. Manual Single Stage Heating: This feature gives the user maximum flexibility to set the oven to desired heating time and power level. Ideal for menus that ’ require various heating requirements. “Example: To-heat for 2 minutes at High Power NE-1054F 4. Beep tone will sound. B. Manual 2 or 3 Stage Heating: +Press the POWER Level Selector ~ Pad one time. *Press the Memory Pads 2, 0 and 0.
C. Programmed Heating: = See page 13 10 program Memory Pad, See page 15 10 activate Program Lock. LE) 3. Beep tone will sound. To Select Multiple Portion Heating: "All heating will stop. *Press the Memory Pad 8. In Program Lock Mode oven will start without pressing START Pad. See page 15. *Press the START Pad. Heating will start, The time in the Display Window will count dowry. “When opening the doer, the display will.stop blinking. s Press the Memory Pad 3.
Programming — DO NOT OPEN THE DOOR — The Display Window MUST be blank before programming can begin. If any indicator light is illuminated in the digital Display Window: Close the door, press STOP/RESET Pad and wait 1 minute until the Display Window goes blank. A. Programming Memory Pads for Single Stage Heat NE-1054F ng: Numb loom; *Press the PRIG, Pad. NOTE: #if no PRIG Indicator appeared in the Display Window, “Program Lock” should be canceled. (See page 15.) *Do not keep pressing PRIG.
NOTE: » Program the remaining Memory Pads as desired by repeating steps 1-5. You may insert up to 10 memory Programs. « When the PRIG indicator is blinking, the program can be canceled and/or the Pad erased by pressing the STOP/RESET Pad. B. Programming Memory Pads for 20r3 Stage Heating +Press the POWER Level Selector Pad 5 times. DEF indicator light will light. «Press the Memory Pads 2, 0 and 0. *Press the PRIG. Pad again.
NE-1054F C. Programming the Double Quantity Pad — For multiple portion heating: Your vane is factory set to automatically double the programmed time for multiple portion heating — this is the correct setting for heating multiple portions of most small foods items. No further programming of the time Is necessary for these food items. The time required to heat multiple portions of some large platters and most bulk food loads is slightly less than double that of a single portion.
Other Features A. To Activate Program Lock: This procedure “Locks” the control panel Memory Pads into their programmed heating times and power levels. DO NOT OPEN THE DOOR. The Display Window must be blank before the Program Lock feature can be activated. *Press and hold in the PRIG. Pad until the display shows . . + “P"and "Ll" (for 6 seconds) ’ . Program Lock feature is now activated. NOTE: +Do not press PRIG. Pad for longer than 30 seconds continuously, or false failure code may result.
a Read Program List: Allows you to review all currently programmed Pad 1. Open the door. 2. | STOP/RESET 4 START NE-1054F NOTE: «If you want to go to another program, press the Memory Pad you desired to read programs Memory Pad is being displayed. «if you want to show the Multiple Portion Heating the Memory Pad. “While pressing the STOP/RESET Pad, press and hold in the START Pad. The Beep Tons setting will show in the Display Window.
D. To Select Beep Tone Options: The Beep Tors can be set, ON or OFF. “1. Pen the door. Read the Cycle Counter: Display Window *Press the PRIG. Pad. The display will not change. 0 *Press the Memory Pad 0. nL “Repeat pressing of 0 Pad, Select "OFF" of Beep Tone. : error Stage Indicator Stage Indicator 2 = OFF Press the PRIG. Pad again. re En You have completed programming the beep tone. *2 seconds later, the Display Window will go blank. The oven can display.
This oven monitors its operation and displays a Failure Code in the Display Window when a problem scours. What to do when a failure code appears: NE-1054F CODE CAUSE WHAT TO DO Fo1 “Overclocked rood *Press STOP/RESET Pad to stop beep. “Temperature of exhaust air too high. | *Wait for oven to cool down and reset. *H a flame is present, do not open oven door. *If normal operation does not resume, call the service agent with information of failure code. .
NE-1054F Power Source 120 V, 80 Hz, single phase Required Power 13.4 A 1,500 W Output” 1,000 W Frequency 2,450 MHz Outer Dimensions 12° x 20%" x 1477" HxWxD) 806 mm x 510 mm x 360 mm Cavity Dimensions fhe" 205 mm x 330 mm x 330 mm Net Weight Approximately 34 lbs (15.4 kg) Shipping Weight Approximately 39 Ibs (18 kg) Tier 89 min 99 sec (Digital) 6 minutes Rotary x 10 Memory Pads with Double Quantity (x2) Pad *IEC Test Procedure Specifications subject fo change without notice 14806" 20 14g" .
Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America One Panasonic Way Se caucus, New Jersey 07094 Panasonic Appliances Microwave Oven (Shanghai) Co., Ltd.
