Operating Instructions - Language - English
39
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
OSD:
• Press the [Cursor] buttons (34) to select [4:3],
[OFF] or [16:9]. (Normally set to [4:3].)
• When using wide screen TV and selecting the wide
screen mode on the TV, indications do not appear.
Therefore, set to [16:9].
• Even if setting to [16:9], indications may be cut off
depending on the TV.
OFF: No indications appear.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
AV2:
• Press the [Cursor] buttons (34) to select the type of
external source equipment which is connected to the
VCR’s AV2 21-pin socket.
• Set the external source equipment as follows:
DECODER: When a decoder is connected.
EXT LINK 1:When a digital receiver which transmits
a special control signal recordings via
the 21-pin Scart cable, for example the
F.U.N. receiver (TU-DSF30/S3) is
connected for the linked timer
recordings. (See page 20.)
EXT LINK 2:When external equipment with a timer
function is connected for the linked
timer recordings. (See page 20.)
NORMAL: When another VCR or a satellite
receiver is connected.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Remote:
• Press the [Cursor] buttons (34) to select the
desired remote control mode.
VCR 1: Select this setting on both the VCR and the
remote control for normal use with one VCR.
VCR 2: Select this setting on both the VCR and the
remote control when using this VCR and
another Panasonic VCR in the same place.
This ensures that you can operate both
VCRs independently with their respective
remote control.
It also allows you to operate both VCRs with
a single remote control, simply by changing
the remote control mode on the remote
control.
• To change the remote control mode on the remote
control itself, change the position of the [VCR 1/2]
switch to match the setting made above.
If these settings are not matched, the remote control
cannot be used to operate the VCR.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
4 Press the [OK] button to finish the settings.
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
5 Press the [EXIT] button to exit the On Screen Display.
VCR
12
123
78
0
9
4
5
6
INPUT SELECT
Í
DIRECT TV REC TV ASPECT
AV LINK
TV / TEXT
TRACKING/V-LOCK
VOLUME
STILL ALBUM
REPLAY
REC
VCR
DATE
CANCEL
AUDIO OSD/DISPLAY
RESET
SP/LP/EP
r
s
r
s
r
s
ON OFF
TV
SV/V
+
AV
+
–
+
–
MENU
EXIT
OK
PROG. / CHECK
TIMER
I-TIMER
Á
LIBRARY/SEARCH
INDEX
2,3
5
3
2,4
1
Other settings
Panasonic VCR
Tape length
Audio playback
SQPB
VCR display
OSD
AV2
Remote
: AUTO (2 E-240)
: NORMAL
: AUTO
: DIMMED
: 4:3
: NORMAL
: VCR 1
Other settings
Panasonic VCR
Tape length
Audio playback
SQPB
VCR display
OSD
AV2
Remote
: AUTO (2 E-240)
: NORMAL
: AUTO
: DIMMED
: 4:3
: NORMAL
: VCR 1
Other settings
Panasonic VCR
Tape length
Audio playback
SQPB
VCR display
OSD
AV2
Remote
: AUTO (2 E-240)
: NORMAL
: AUTO
: DIMMED
: 4:3
: NORMAL
: VCR 1
On Screen Display
Example of NV-FJ730B
VCR
12
OK
EXIT
Manual Setup