Operating Instructions - Language - English

ManualsBrandsPanasonic ManualsAV ProductsNVFJ780B

Auto Setup (For TV and/or VCR without Q Link Functions)

1 Set the [VCR/TV] switch to [VCR]. Turn on the TV, then

press the [VCR-ON/OFF] button to switch the VCR on.

The VCR will now start Auto Setup.

• If Auto Setup has previously been completed this

indication will not appear.

In this case you can re-start

Auto Setup again. See page 34.

• In some cases, where the VCR has been connected to

your TV using the RF lead only (no Scart) the RF

output channel may interfere with the TV stations

transmitted in your area. This may prevent you from

seeing the On Screen Display clearly.

Please refer to page 10

for removing the interference

before restarting Auto Setup (page 34)

• If you want to cancel Auto Setup before it has finished,

press the [EXIT] button. You can restart Auto Setup

again, see page 34.

• The first digit of the VCR display will begin to flash.

After a while, it will stop flashing and the RF output

channel number will be displayed.

• If you have connected the VCR to the TV with a Scart

lead, you will see the screen on the right during Auto

Setup. You can skip step

below.

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

2 Select an unused channel pre-set on your TV and tune

it to the RF output channel number shown on the VCR

display (or until you can clearly see the Auto Setup

screen shown on the right). Store the new video

playback channel (refer to the instructions for your TV).

• If you can see interference on the picture, you may

need to change the RF output channel. Follow the

instructions on the next page to do this.

3 Press the [EXIT] button. The Owner ID screen will

appear.

You can complete the Owner ID now or skip this step

and do it later. To do it later, press the [EXIT] button

again. Your VCR is now ready to use.

4 To set the Owner ID now, press the [Numeric] buttons

or [Cursor] buttons (34) to enter a four-digit PIN

number. If you make a mistake then press the [Cursor]

button (2) and the re-enter the correct digit. Make sure

that you will remember the PIN number (make a note of

it).

5 Press the [OK] button and the [Cursor] button (4).

The cursor moves to [Name].

6 Press the [Cursor] button (1).

7 Press the [Cursor] buttons (34) to select a letter and

then press the [Cursor] button (1) to move to the next

letter.

Repeat these steps until you have entered your name.

8 Press the [OK] button to finish setting your name.

9 Enter the [House No] and [Postcode] in the same way.

10 When you are happy with the information that you have

entered, press the [EXIT] button to leave the Owner ID

screen. You will now see the TV picture.

Your VCR is now ready to use.

START

VCR

123

INPUT SELECT

DIRECT TV REC TV ASPECT

AV LINK

TV / TEXT

TRACKING/V-LOCK

VOLUME

STILL ALBUM

REPLAY

REC

VCR

DATE

CANCEL

AUDIO OSD/DISPLAY

RESET

SP/LP/EP

ON OFF

SV/V

–

EXIT

PROG. / CHECK

TIMER

I-TIMER

LIBRARY/SEARCH

INDEX

1,3,10

5,8

6,7

4,7

FINISH

Tuning

: Ch 21

Auto-Setup

Panasonic VCR

Auto-Setup

Panasonic VCR

Auto setup is now complete

(Output channel is 28)

PIN number :846¢

Name :¢¢¢¢¢¢¢¢¢¢¢¢¢¢

House No :¢¢¢¢¢¢¢¢¢¢¢

Postcode :¢¢¢¢¢¢¢¢¢¢¢

Owner ID

Panasonic VCR

BBC1

VCR Display

On Screen Display

EXIT

Quick Start

Guide

VCR

123