Contents Video Cassette Recorder NV-SV121EB Operating Instructions Super VHS EJECT SUPER LP . 35x JET SEARCH TIMER REC REC 3D DNR CH PULL OPEN TBC ET S-VHSET VHS PAL 625 Before connecting the device, operating it or adjusting settings please read these operating instructions completely; especially the safety precautions on pages 2-3.
Important Safety Warnings ! The moulded three pin mains plug is supplied for your safety and convenience and must NOT be cut off. ! A 5 amp fuse is fitted in the mains plug. If the fuse has to be replaced, it must be of the same rating and approved by ASTA or BSI to BS1362. Check for the ASTA mark or the BSI mark on the body of the fuse. To replace the fuse, open the fuse compartment with a screwdriver as shown and replace the fuse and the cover securely. 2 Fuse cover 1.
Caution ! Avoid exposing the unit to direct sunlight or other heat sources. ! Avoid sudden change in temperature or humidity, dew or condensation may form, causing malfunction. Dispose of batteries in accordance with the instructions given in this book. Place the unit on a flat, stable surface. Do not place heavy object on top of the unit. Your attention is drawn to the fact that recording of pre-recorded tapes or discs or other published or broadcast materials may infringe copyright laws.
Sales and Support Information Customer Care Centre ! For UK customers: 08705 357357. ! For Republic of Ireland customers: 01 289 8333. ! Visit our website for product information www.panasonic.co.uk. ! E-mail: customer.care@panasonic.co.uk. Direct Sales at Panasonic UK ! ! ! ! ! ! 4 Order accessory and consumable items for your product with ease and confidence by telephoning our Customer Care Centre Mon - Friday 9:00am - 5:30pm (Excluding public holidays).
Included Accessories Included A VCR TV CH VOL AV TRACKING/V-LOCK 1 2 3 4 5 6 7 8 9 CH AV LINK EXT LINK INPUT SEL 0 ShowView AUDIO PROG /CHECK ccessories STATUS RESET/CANCEL PROG PLAY I-TIMER EXIT MENU AC Mains Lead RJA0044-3C Batteries for the Remote Control R6 size Remote control N2QAJB000089 Operating Instructions RQTD0086-B RF cable Quick Start Guide RQCAD0013 ENTER PAUSE/SLOW JET REW INDEX TIMER REC MODE OFF-TIMER REC A * Some functions may not be applicale to
Front Panel VCR 1 3 2 4 Super VHS EJECT VCR= Video Cassette Recorder Detailed information is available on the specified pages. SUPER LP . 35x JET SEARCH TIMER REC REC 3D DNR CH PULL OPEN TBC ET Page 5 6 Front AV (AV3) 1 S-VIDEO IN (AV3) VIDEO IN (AV3) AUDIO IN (AV3) 2 3 4 JET REW 7 8 9 10 11 Stand-by/on switch /I. CH 3D DNR EJECT Selects a channel. 3-Dimensional Digital Noise Reduction. 20 Ejects the cassette. 23 21 Activates the recording timer.
Rear Panel VCR Rear Panel Connectors AV OUT VIDEO AC IN ~ L S VIDEO RF IN AV1 (TV) AV2 (DECODER/EXT) AUDIO R RF OUT AV2 ( 1 234 1 AC IN~ (Power supply) 2 S-VIDEO output 3 VIDEO output 4 AUDIO output 5 6 5 6 7 8 78 AV1 (21-pin Scart socket) AV2 (21-pin Scart socket) RF IN = Aerial input RF OUT = Aerial output L = AUDIO output left channel R = AUDIO output right channel Inserting batteries into the remote control unit: The batteries last for about a year, depending on how often you use t
Remote control functions TV Controls VCR Some Panasonic television sets may be controlled with the remote control unit of this VCR. However, some of old Panasonic TVs cannot be operated using this remote control. Press to switch the TV from on to stand-by mode or vice versa. TV CH VOL AV TRACKING/V-LOCK 1 2 3 4 5 6 7 8 9 CH AV Selects the TV set´s AV port. CH TV Channel selector. EXT LINK INPUT SEL 0 VIDEO Plus+ AUDIO VOL PROG /CHECK VCR Playback Control Normal playback.
VCR Standard Controls VCR MENU EXIT INPUT SEL RESET/CANCEL Stand-by/on switch Press to switch the unit from on to stand-by mode or vice versa. In stand-by mode, the unit is still consuming a small amount of power. Displays the menu. 19 Quits a menu. 19 AUDIO Audio out settings. 40 Selecting or storing settings. ENTER Menu navigation buttons. Switches between AV inputs A1, A2 and Tuner. TRACKING/V-LOCK Channel select buttons. 21 CH RESET : Resets the counter to 0:00.00.
Connecting with RF cable You can connect the VCR to your TV set by using a RF cable. 2 Aerial Follow the steps described below. RF IN (Aerial input) AC IN~ 1 Ensure TV Power is disconnected from AC Mains socket. VCR AV2 ( 2 Connect aerial to the RF IN (Aerial input) connector of the VCR. RF OUT (Aerial output) 4 AC mains lead 3 Connect the VCR´s RF OUT (supplied) RF cable (supplied) TV (Aerial output) to the TV set’s aerial in connector.
VCR Auto Setup with RF cable (Automatic tuning) ! ! VCR Display ! - While Auto Setup is running the first digit of the VCR display will flash. After a while it will stop flashing and the RF output channel number will be displayed. - Select an unused channel pre-set on your TV and tune it to the RF output channel number shown on the VCR display (or until you can clearly see the Auto Setup screen). Store the new video playback channel (refer to the instructions for your TV).
Connecting with 21-pin Scart cable (Fully wired) AV1 21-pin Scart socket 2 Aerial Follow the steps described below. RF IN (Aerial input) ACININ~ AC VCR 1 Ensure TV Power is disconnected from AC Mains socket. AV2 ( RF OUT (Aerial output) 3 RF cable (supplied) 2 Connect aerial to the RF IN (Aerial input) connector of the VCR. 3 Connect the VCR´s RF OUT 5 AC mains lead (Aerial output) to the TV set’s Aerial in connector.
VCR Auto Setup with 21-pin Scart cable (Automatic tuning) VCR Display Auto Setup ! ! Tuning : Ch 21 ! EXIT : exit Owner ID Owner ID PIN number : **** Name : ************** House No : *********** Postcode : *********** You now have the opportunity to enter your details and help the police crack crime see instruction book. ENTER :select : exit : store EXIT Datumset Clock / Zeit MANUAL Time Date Turn on your television set. With the Stand-by/on switch turn on the VCR.
Connecting to Satellite Receiver, Set Top Box You can connect a Set Top Box to receive digital broadcast by aerial (DVB-T) signals, a satellite receiver (digital/analogue) or a decoder to decrypt encrypted programmes. 1 Ensure TV Power, External unit Power and VCR Power are disconnected from AC Mains socket. Aerial 2 Connect a 21-pin scart cable (fully wired) to the AV2 21-pin scart socket on the VCR and to the 21-pin scart socket on the external unit.
Connecting with S-Video cable Audio Output sockets AC S-Video IN Output socket RF IN (Aerial input) 2 Aerial Aerial Input socket Audio Input sockets TV with S-Video Input socket ACININ~ AC AV2 ( 3 RF cable RF OUT (Aerial output) AC mains 1 socket (supplied) 4 Audio cables AC mains 1 socket AC mains lead 5 (supplied) 4 S-Video cable S-Video Input socket 5 AC mains lead Follow the steps described below. 1 Ensure TV Power and the VCR Power are disconnected from AC Mains socket.
Connecting Audio Systems For details about the connection, also read the operating instructions of the Audio System. Be sure to keep the VCR, TV and Audio System disconnected from mains until you have finished all connections. Follow the steps described below. 1 Ensure Audio Systems Power, VCR Power and TV Power is disconnected from AC Mains socket. VCR 2 Connect an Audio cable (not AV2 ( supplied) to the Audio Output sockets on the VCR and to the Audio Input sockets on the Audio System.
Checking the Settings after Auto Setup To confirm that the TV stations have been tuned correctly by Auto Setup MENU ! ! ! Menu Timer recording Tuning Clock set Others :select : exit ENTER D : access D EXIT Tuning Manual Auto Setup Shipping condition Owner ID : select : return MENU ENTER EXIT : access : exit EXIT Press the MENU button to display the OSD Main menu on the TV screen. Press to select Tuning then press the ENTER button.
Removing Interference / Changing RF-output channel In some cases, interference (lines or patterning) or a very poor picture may appear on the TV when the VCR is connected. If this happens, follow the steps below to change the video playback channel (RF output channel) to remove the interference. TV screen The picture with interference MENU ! Press the MENU button for more than 5 seconds. The RF output channel number is displayed on the VCR display.
Menu System Timer recording Pos Date 27 28 ------- ------------------- ------- / / / / / / ------- 1/3 PDC Start Stop --:---:---:---:---:---:-- --:---:---:---:---:---:-- - ------------- Tuning Menu Timer recording Tuning Clock set Others 17 ENTER ! Manual Auto Setup Shipping condition Owner ID ! ! ! ! Press EXIT to leave the menu. ! 11 13 AUTO Time Date : 12 : 00 : 00 : 11. 6. 04 Others 37 Press MENU, the menu screen appears. With select the desired sub-menu.
Playback Normal playback ! Turn on the VCR. ! Be sure the TV set is turned on and tuned to the video playback channel. ! Insert a video cassette. ! Press PLAY to start playback. ! Press STOP to end playback. Repeat playback ! The VCR repeats playback from beginning to the end of the recording. ! In stop or playback mode press PLAY for longer than 5 seconds. The symbol [R] appears on the VCR´s display. ! Press STOP to end playback. PAUSE/SLOW Still playback ! Press PAUSE/SLOW during playback.
Tracking control Adjusting the playback picture Under normal conditions, the VCR automatically adjusts the tracking for optimum performance. However, in some cases it may be necessary to adjust it manually. Playback picture containing noise bars If the picture contains noise bars and it is not clear to see (tracking adjustment): If noise bars appear during normal playback, slow playback or still playback, follow the operations below.
General convenient functions Auto-Start When inserting a cassette the VCR will automatically switch on. Automatic rewinding When a cassette is played to the end, the VCR will automatically rewind it to the beginning of the tape. D This function is not available during programmed recording sessions. Search forward or backwards ! While playing back press or , the search begins. ! When pressing the button twice (JET SEARCH) the search speed increases.
Tape Care General convenient functions Tape Counter When inserting a video cassette the tape counter will automatically reset to [0:00.00]. ! The tape counter may also be reset to [0:00.00] by pressing the RESET/CANCEL button. EJECT Automatic shut down and removing cassettes If the VCR is switched into stand-by mode, the cassette may be removed by pressing the EJECT-button. Once done the VCR will switch back to stand-by mode.
Recording S-VHS Recording Recording functions S-VHS Recording 24 25 Recording Instant recording of the VCR - TV picture. Insert an S-VHS cassette and set the [S-VHS REC] to [ON], so that the SVHS indicator is lit (See page 37). Recording is performed in the S-VHS format. When a cassette that was recorded in the S-VHS format is played back on a VHS VCR without S-VHS quasi playback function, noisy playback picture will appear. 26 Timer recording Recording controlled by timer.
S-VHS / VHS Recording The following table lists the playback formats that are compatible with this VCR’s recording standard. Cassette Recording format Compatible Playback Equipment VHS (SP/LP/EP) VHS, S-VHS, VHS with SQPB*1 S-VHS ET (SP) S-VHS*2, VHS with SQPB VHS (SP/LP/EP) VHS, S-VHS, VHS with SQPB S-VHS (SP/LP/EP) S-VHS, VHS with SQPB VHS S-VHS *1 SQPB stands for S-VHS quasi playback. *2 Some models are not compatible. D D D D We recommend that you use cassettes other than type E300.
Recording REC Instant recording Set the TV set to the video channel and insert a cassette into the VCR; make sure that the cassette’s protection tab is intact. ! Select channel to record from. ! When recording from an external device, select from Scart inputs AV1, AV2. ! Press REC to start recording. ! Press STOP to stop recording. ! Press PAUSE/SLOW to pause recording. ! To protect the video heads this function will be terminated after approx. 5 minutes.
Timer recording Timer recording Pos 1 2 3 4 5 -- Date BBC1 31/12 BBC2 31/12 ITV 31/12 CH4 31/12 CH5 31/12 - - - - - -/ - :select : delete CANCEL The Timer recording allows you to programme the recording time of TV programmes up to 1 month in advance. Use the on-screen menu to programme a maximum of 16 recordings. Do not forget to verify that there is enough tape left. The length of the recording must not exceed the tape left on the video cassette.
Timer recording Checking the timer programme ! ! Press PROG/CHECK, the Timer recording menu appears. Press PROG/CHECK again or EXIT to quit the menu. Changing or cancelling a timer programme ! ! ! ! PROG /CHECK PROG /CHECK Press PROG/CHECK, the Timer recording menu appears. With select the entry you would like to edit, confirm with ENTER. Modify entries with and confirm with ENTER. Press RESET/CANCEL to delete a recording. PROG PLAY Playing back programmed recordings ! Press PROG PLAY.
Recording with INTELLIGENT TIMER INTELLIGENT TIMER Pos Date Start Stop 25/10/04 PDC 1 BBC1 25/10 10:30 11:30 SP ON 1 BBC1 25/10 18:3019:30 SP OFF 2 BBC2 25/10 12:30 13:30 A ON Timer recording Pos Date 1 1 ----- BBC1 BBC1 ------------- I-TIMER 1/3 Start Stop PDC I-TIMER 26/10 10:30 11:30 SP ON 26/10 18:30 19:30 SP OFF -- / ---:-- --:-- ---- / ---:-- --:-- - ---- / ---:-- --:-- - ---- / ---:-- --:-- - --- INTELLIGENT TIMER Pos The INTELLIGENT TIMER allows you to easily time the recording of prog
Recording with VIDEO Plus+ Video Plus+ 8 3 5 4 2 - - - - Programming recordings with the VIDEO Plus+ function The VIDEO Plus+ code simplifies entering programme information to record TV and SAT programmes. The recording time may be slightly longer than the TV programme. VIDEO Plus+ ! ! ! 0 - 9 :enter : correct : access : exit ENTER EXIT Timer recording Pos 1 1 2 ---- Press VIDEO Plus+. Enter the VIDEO Plus+ number ( to correct entry). Confirm entry with ENTER. The Timer recording screen appears.
Recording with VIDEO Plus+ VIDEO Plus+ Codes for Satellite Receivers / Set Top Box This VCR is not designed to control (switch on or change channel) your satellite receiver or Set Top Box, however, it can be taught to recognise VIDEO Plus+ Codes for Satellite stations. The Satellite Receiver or Set Top Box must be switched on and the correct station selected. Some receivers have their own timer facility for this purpose.
Recording with external recording controls Receiver Aerial TV VCR Others 2/2 S-VHS REC S-VHS ET REC EXT LINK MENU : select : return EXT LINK : ON : OFF : 2 ! ! EXIT : exit D EXT LINK 32 EXT LINK The AV2 input of this VCR is equipped for use with external equipment having external timer recording control such as digital satellite receivers. The AV2 input can be set to EXT LINK 1 or EXT LINK 2 depending on the equipment to be connected. Fully wired 21-pin scart cable is required.
Editing Assemble Editing Assemble editing is the process of copying scenes from an external source (e.g. video movie camera or another VCR) to this VCR. These scenes can be assembled in the order of your choice to create your own unique composition. TIMER REC REC ! PULL OPEN JET REW QUICK ERASE ! ! L S-Video R ! Video Audio D Video movie camera D Rear Panel VCR AV1 (TV) AV1 Connect the external source to this VCR with an audio/video cable or a 21-pin Scart cable, as shown in the illustration.
Manual Functions This VCR has 99 programme positions that can be tuned to receive TV stations. In certain circumstances you may wish to tune in a station manually or rename a TV station.
Manual Functions Changing the name of TV stations Tuning Pos 1 2 3 4 5 Name BBC1 BBC2 ITV CH4 CH5 Ch 22 23 24 25 26 : delete select MENU : return Pos Name Ch 6 30 7 ---- --8 ---- --9 ---- --10 - - - - - - - ! ! ! ! ! : move ENTER : access EXIT : exit A B ! Pos Name Channel NICAM MENU 1 : BBC1 : 22 : AUTO : ! ! ! ! : select : return EXIT ! : exit 1 2 3 4 5 BBC1 BBC2 ITV CH4 CH5 : delete move MENU : return A With select the name entry. The cursor will mark the first letter BBC1.
Manual Functions Creating a new station table Tuning Manual Auto Setup Shipping condition Owner ID ! ! ! ! Press MENU, the Menu screen appears. With select the Tuning menu, confirm with ENTER. With select [Auto Setup], confirm with ENTER. Press ENTER to confirm. OK? ENTER : yes EXIT : no Auto Setup D D Tuning : Ch 1 Manual Auto Setup Shipping condition Owner ID OK? EXIT : no Shipping condition resets the VCR back to the original factory settings except Owner ID information.
Manual Functions Tape length Others Menu AV2 Displaying the Others Menu ! Press MENU and select Others . ! Press ENTER. The Others menu appears. Others 1/2 Tape length AV2 AV2 IN AV1 OUT S-VHS playback OSD VCR display MENU ! : select : return : : : : : : : EXIT AUTO ( E-240) NORMAL VIDEO VIDEO AUTO 4:3 DIMMED Others VIDEO : Video signal via the 21-pin scart cable. S-VIDEO : S-Video signal via the 21-pin scart cable.
Manual Functions Tuning Owner ID Manual Auto Setup Shipping condition Owner ID ! ! ! ! Owner ID PIN number Name House No Postcode ! : 846* : ************** : *********** : *********** ! ! EJECT Owner ID Name House No Postcode 38 : MARWIN : BANKS : RG12 8FT Press MENU and select Tuning . Press ENTER. Select Owner ID and press ENTER. Use the Numeric buttons or to enter the current PIN number. After entering the correct PIN number, you can change the Name, House No and Postcode.
Manual Functions Menu ENTER : access EXIT Datumset Clock / Zeit MANUAL Time Date : 12 : 00 : 00 : 11. 6. 04 Datumset Clock / Zeit AUTO Time Date The clock will normally be set correctly during Auto-Setup however, in some circumstances the VCR cannot set the clock automatically. In this case, follow the operation steps below to manually set the clock. To manually adjust the clock ! Press MENU and select Clock set . ! Press ENTER. ! Confirm that Clock set is set to MANUAL, and press ENTER.
Manual Functions AUDIO Audio mode (L/R) At each press of the AUDIO button, the selected sound output is indicated with L (Left) and R (Right). Stereo playback : Display: LR Left audio channel playback : Display: L Right audio channel playback : Display: - R Playback of normal audio (Mono) sound : Display: - - NICAM sound system The NICAM System is a 2 channel digital sound broadcast system which in most instances provides high quality stereo sound.
Before requesting service Please contact our after sales service centre if you fail to remove problems by yourself (see Guarantee Information). I HAVE AN ON SCREEN MESSAGE. You have attempted to carry out a function, which is not possible at this time. It may be that no tape is inserted and you have pressed PLAY or that you tried to change the details of a timer recording whilst it was being carried out. ! Please follow the instructions as given on the display. THE VCR DISPLAY IS NOT ILLUMINATED.
21-pin Scart Socket 21-pin Scart Socket 1 3 5 7 9 11 13 15 17 19 21 2 4 6 8 10 12 14 16 18 20 The 21-pin Scart socket transmits both input and output signals for picture and sound. TVs equipped with the same type of socket can be connected here. This type of socket is also called Peritel, Euro Connector and Euro AV.
Specifications NV-SV121EB Option Power supply Power consumption in operation Technical data 220-240 V AC, 50/60 Hz 18W multifunctional remote control (VCR and Panasonic TV) / Controls VCR direct controls (main functions) Video and Audio heads (helical scanning system) 4 heads (Super Ferrite Head) / 2 heads Hi-Fi Tape speed SP: 23.39 mm/s, LP: 11.7 mm/s Record and playback time (E240 cassette) SP: 240 min, LP: 480 min Fast forward or fast rewind time (E180 cassette) approx.
Index Aerial cable Aerial input/output AUDIO AUDIO output Auto Setup AV1 AV2 Batteries Channel Clock Date Digital Receiver Dimmed Erasure protection External Devices EXT LINK Factory defaults INDEX INTELLIGENT TIMER Page 10,12,14 7 40 7,16 11,13,36 7 7,32,37 7 18,34 11,13,39 27,30 14,32 37 23 14,37 32,37 36 JET SEARCH JET REWIND Page 22 22 Manual Tuning Mono 34 40 NICAM NTSC 40 23 OFF TIMER 22 37 OSD Playback PDC PROG PLAY 8,20 28 28 Quick Erase 6,23 Recording Remain Remote Repeat Playba
