Quick Start Guide

ManualsBrandsPanasonic ManualsAV ProductsNVMV20EBL

-6-

EXT LINK

TV ASPECT

TV/TEXT

TRACKING/V-LOCK

VOLUME

INPUT SELECTINPUT SELECT

INDEX

PROG PLAYPROG PLAY

AUDIO

REC

ENTER

VIDEO Plus+

TV screen

The picture with interference

The clear picture

On-Screen Display

Test pattern indication

VCR display

Indication when the RF output

channel is 28 (example)

Indication after changing the RF

output channel to 31 (example)

Test pattern indication

(RF OFF)

...

VCR

123

---------------------------------------------------------------- ---------------------------------------------------

Removing InterferenceRemoving Interference

In some cases, interference (lines or patterning) or a very poor picture may appear on the TV when the

VCR is connected. If this happens, follow the steps below to change the video playback channel (RF

output channel) to remove the interference.

Set the switch to .VCR/TV VCR

Press the button for more than 5 seconds.MENU

The RF output channel number is displayed on the

VCR display.

Press the buttons or use the buttonNumeric Channel

to select a channel number, which differs by 2 or 3 from

the present channel number. (For example, if the

original channel number was 28, enter 31.)

Set the RF output channel of the VCR to [- -] (RF OFF)

if the VCR is connected to the TV via the 21-pin Scart

cable.

Press the numeric button or button to0 Channel display

[- -]. Skip step 4, if using a 21-pin Scart cable.

Retune your TV until you receive the Test pattern. It

may be necessary to repeat steps and above until

you can see the Test pattern clearly.

Press the button to finish this setting.ENTER

VCR Ch:28

VCR Ch:31

EXT LINK

TV ASPECT

TV/TEXT

TRACKING/V-LOCKTRACKING/V-LOCK

VOLUME

INPUT SELECTINPUT SELECT

INDEX

PROG PLAYPROG PLAY

AUDIO

REC

PDC

SL/LP/EP

PROG./CHECKPROG./CHECK

TIMER

OFF TIMER

OSD/DISPLAY

RESET/CANCELRESET/CANCEL

I-TIMER

ENTER

VIDEO Plus+

2,3

On-Screen Display

EXIT

---------------------------------------------------------------- ---------------------------------------------------

Notes:

Tuning

Pos Name Ch Pos Name Ch

6 ---- ---

---- ---

1 BBC1 22

2 BBC2 23

3 ITV 24

4 CH4 25

5 CH5 26

ENTER

Tuning

Manual

Auto-Setup

Shipping condition

Owner ID

Timer recording

Tuning

Clock set

Others

Checking the Settings for Auto Setup

To confirm that the TV Stations have been tuned correctly by Auto Setup

Press the button to display the OSD Menu on

the TV screen.

Press the buttons ( ) to select [Tuning] then

press the button.

Cursor

ENTER

Press the buttons ( ) to select [Manual] then

press the button to display the list of tuned TV

stations and confirm that all available TV stations have

been set correctly. Positions 5 and 6 may differ from the

example shown. If Channel 5 is received, it is usually

found on programme position 5 and a connected

satellite receiver on programme position 6. If Channel 5

is not received but a satellite receiver is connected, then

the satellite receiver is found on programme position 5.

Cursor

ENTER

List of tuned TV stations

(example)

Press the button to exit the On-Screen Display.EXIT

If the station names and/or channel numbers have not been set correctly.

See page 34 of Operating Instructions for details.

If the station name is [ ]:

The asterisks indicate that Auto Setup found a station but did not assign a name to it (due to a weak signal).

If the station name is [----]:

The dashes represent unused channel positions.

Stations on the list marked by an asterisk will need to be named manually. (See page 35 of Operating Instructions.)

Stations on the list marked by dashes will need to be set manually. (See page 34 - 36 of Operating Instructions.).

When no stations have been set, confirm all connections and restart Auto Setup.

You can restart Auto Setup, without using remote controller, by pressing some buttons on the front

of the unit. Hold down and on the main unit simultaneously for about 5 seconds.