Operating Instructions

4
LSQT0880
Connections
This section shows you how to connect the VCR to an aerial,
TV, etc.
Basic Connections
The following connections are required to record and play
back the video cassette through the TV.
Connection to a TV using the Audio/Video Input Socket:
Set the RF output channel of the VCR to [ss] (RF OFF)
when the VCR is connected to the TV via the Audio/Video
cable. (See to the right.)
Tuning the TV to Your VCR
The VCR supplies a signal to the TV via the RF coaxial cable
on channel E21-E69.
If you have connected the VCR to the TV through the Audio/
Video input sockets, then you do not need to follow the
procedure below. To view the pictures from the VCR, set to
the AV mode on the TV with [AV] (2).
Preparation
• Turn on the TV and the VCR.
Operations
1 Set the TV to an unused position which you wish to
use for your video playback.
• Tune the TV until the display shown below appears on
the screen. (Please refer to the TV manufacturers
operating instructions regarding tuning.)
• Set [RF SELECT] by pressing [21] (28) to select the
colour TV system used by the TV set to be connected.
BG: PAL B.G.H/SECAM B.G
I: PAL I
DK: PAL D/SECAM D.K.K1
2 Press [MENU] (9).
• If Auto Tuning stops halfway, refer to “To Restart Plug in
Auto Tuning”. (See page 5.)
To Change the RF output Channel
You can change the RF output channel, for example, when
interference occurs on the picture after tuning.
Operations
1 Hold down [MENU] (9) for 5 seconds or more.
• The VCR display changes as shown below and the VCR
picture on the TV displays this pattern.
2 Enter the desired channel number (E21-E69) by
[Numeric] (3) or [CH] (20).
• Set the RF output channel of the VCR to [ss] (RF OFF)
when the VCR is connected to the TV via the Audio/Video
cable.
• Press [CH] (20) to display [ss].
• It is also possible to select by pressing [Numeric] (3).
Example:
3 Press [MENU] (9) to finish the setting mode.
4 Retune your TV to the new RF channel for the VCR.
Note:
• Even if the RF output channel has been changed, it is not
necessary to perform Auto Tuning.
AUDI O
VIDEO
A C I N ∼
OUT IN
(
AV1
)
IN
OUT
RF
(6)
(3)
(5)
(4)
(1)
(2)
¢
(1) Aerial (Not supplied)
(2) TV Set (Not supplied)
(3) Aerial Connector
(4) RF IN socket (42)
(5) RF OUT socket (45)
(6) AC Input socket (39)
¢ To mains supply
3 pin mains plug is for Saudi
Arabia.
AUDI O
VIDEO
A C I N ∼
OUT IN
(
AV1
)
IN
OUT
RF
(10)
(3)
(4)
(6)
(5)
(9)
(8)
(7)
(1)
(2)
¢
(1) Aerial (Not supplied)
(2) TV Set (Not supplied)
(3) Aerial Connector
(4) VIDEO IN
(5) AUDIO IN
(6) Audio Cable/Video Cable
(Not supplied)
(7) RF IN socket (42)
(8) RF OUT socket (45)
(9) VIDEO OUT (41)/
AUDIO OUT (44)
(10)AC Input socket (39)
¢ To mains supply
3 pin mains plug is for Saudi
Arabia.
RF SELECT [BG] I DK
END: MENU
AUTO TUNING IS
COMPLETED.
RF SELECT:
CH 22 SEARCH
END: MENU
21
AUTO TUNING
IN PROGRESS,
PLEASE WAIT.
During Plug in Auto Tuning After Plug in Auto Tuning
Panasonic VCR
END: MENU
RF SELECT:
RF SELECT [BG] I DK
21
ss
69
(RF OFF)
2 8
28:
LSQT0880_Eng.book 4 ページ ２００５年２月１６日 水曜日 午後３時３６分