Power Supply Built-in Compact Multi-voltage Photoelectric Sensor NX-5 Series USER’S MANUAL WUME-NX5-3 2015.4 panasonic.
Contents 1. Cautions···························································································3 2. Part description··················································································4 3. Mounting··························································································6 3-2 Mounting interval (thru-beam type NX5-M□)················································· 7 3-3 Long sensing range retroreflective type sensor (NX5-RM7□)···························· 9 4.
1. Cautions WARNING ●● Never use this product as a sensing device for personnel protection. ●● In case of using devices for personnel protection, use products which meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country. ●● ●● ●● ●● ●● ●● ●● ●● This product has been developed / produced for industrial use. Make sure that the power supply is off while wiring. Take care that wrong wiring will damage the sensor.
2.
Thru-beam long sensing range type receiver: NX5-M30□ Retroreflective long sensing range type: NX5-RM7□ Operation indicator (Red) Lights up when the sensing output is ON Stability indicator (Green) Lights up under the stable light condition or the stable dark condition 5
3. Mounting 3-1 Installing to sensor mounting bracket The tightening torque should be 0.8 N·m or less.
3-2 Mounting interval (thru-beam type NX5-M□) ●● In case mounting two sets or more of the this product close together, mount them as drawing left indicates (typical example) ●● Find out the operating point ℓ on the parallel deviation diagram for the setting distance L. Separate sensors by 2 × ℓ or more.
L ℓ ℓ Type NX5-M10R□ NX5-M30□ L 10m 30m ℓ Approx. 888mm or more Approx. 2,400mm or more ●● Since retroreflective type NX5-PRVM5□/NX5-RMA□ and diffuse reflective type NX5-D700A□ incorporate auto interference prevention function, the sensors can mount closely.
3-3 Long sensing range retroreflective type sensor (NX5-RM7□) ●● Please take care of the following points when detecting materials having a gloss with retroreflective type sensor (NX5-RM7□). 1. Make L, shown in the diagram, sufficiently long. (Note) 2. Install at an angle of 10 to 30 degrees to the sensing object. Reflector Glossy surface Sensing object 10 to 30° Sensor L The distance L should be as long possible.
4.
5. Adjustment 5-1 Light axis adjustment (thru-beam type NX5-M10R□ / NX5-M30□) (retroreflective type NX5-PRVM5□ / NX5-RM7□) Thru-beam type NX5-M10R□ / NX5-M30□ 1. Place the emitter and the receiver face to face along a straight line, move the emitter in the up, down, left and right directions, in order to determine the range of the light received condition with the help of the operation indicator (red). Then, set the emitter at the center of this range. 2.
5-2 Sensitivity adjustment Step 1. Turn the sensitivity adjuster fully counterclockwise to the minimum sensitivity position (MIN.) Sensitivity adjuster MIN. MAX. 2. In sensing object present condition, turn the sensitivity adjuster slowly clockwise and confirm the point A where the sensor enters the “Light” state operation. Operation indicator (Red) A MIN. MAX. 3.
6. Automatic interference prevention function ●● The retroreflective type NX5-PRVM5□ / NX5-RM7□ and the diffuse reflective type NX5-D700□ incorporate an automatic interference prevention function, so that two sensors can be mounted closely. (Thru-beam type NX5-M10R / NX5-M30□ does not incorporate the automatic interference prevention function.) Note: If NX5-D700□ are mounted facing each other, they should be angled so as not to receive the beam from the opposing sensor or to detect its front face.
7. Stability indicator ●● The stability indicator (green) lights up when the incident light intensity has sufficient margin with respect to the operation level. Incident light intensity level is such that the stability indicator light up, stable sensing can be done without the light received operation and the light interrupted operation being affected by a change in ambient temperature or supply voltage.
8. Retroreflective type sensor with polarizing filter (NX5-PRVM5□) If a shiny object is covered or wrapped with a transparent film, such as those described below, the retroreflective type sensor with polarizing filters NX5-PRVM5□ may not be able to detect it. In that case, take the following measures given below.
9. Option 9-1 Slit mask (exclusively for thru-beam type sensor NX5-M10R□ / NX5-M30□) With the slit mask OS-NX5-3×6, the sensor can detect an object as small as 3 × 6mm. However, the sensing range is reduced when the slit mask is mounted. Type Model No. Slit mask Slit mask Exclusively OS-NX5-3×6 for thrubeam type Sensor NX5-M10R□ NX5-M30□ Sensing distance Min.
9-2 Interference prevention filter (exclusively for thru-beam type sensor NX5-M10R□) ●● By mounting interference prevention filters PF-NX5-□, two sets of NX5-M10R□ can be mounted close together. However, the sensing range is reduced when the interference prevention is mounted. ●● The filters can be mounted by the same method as for the slit masks. ●● There are two types of interference prevention filters.
9-3 Reflector / reflective tape (retroreflective type NX5-PRVM5□ / NX5-RM7□) ●● Reflector RF-230 is accessory of retroreflective type NX5-PRVM5□ and NX5-RM7□. ●● By using reflector (optional) or reflectivity tape (optional), small object can be detected. However, the sensing distance would be shorter by using reflector (optional) or reflectivity tape (optional). Designation Model No.
10. Specification Thru-beam Type Model Light-ON No. (Note 1) Dark-ON Retroreflective Long sensing range With polarizing filters (Note 2) Long sensing range NX5-M10RA NX5-M30A NX5-PRVM5A NX5-RM7A Diffuse reflective NX5-D700A NX5-M10RB NX5-M30B NX5-PRVM5B NX5-RM7B NX5-D700B Sensing range 10m 30m 0.1 to 5m (Note 3) 0.
Notes: 1) The model No. with suffix “P” shown on the label affixed to the thru-beam type sensor is the emitter, “D” shown on the label is the receiver. (e.g.) Thru-beam type sensor emitter: NX5-M10RP, Thru-beam type sensor receiver: NX5-M10RAD 2) The retroreflective type sensor with polarizing filters may not stably detect specular or glossy objects through transparent film since light is polarized by the transparent film.
11. Dimensions Thru-beam type emitter: NX5-M10R□, Thru-beam long sensing range type: NX5-M30□ (Unit: mm) 18 35 6 20 50 62 Beam axis 2-ø4.5 mounting holes 2-M4 nut seats (on both sides) 4 5 25 ø5.8 cable, 2m long Thru-beam type receiver: NX5-M10□ (Unit: mm) 18 35 6 20 Beam axis 50 62 2-ø4.5 mounting holes 2-M4 nut seats (on both sides) 4 5 25 ø5.
Retroreflective with polarizing filters type: NX5-PRVM5□, Diffuse reflective type: NX5-D700□ (Unit: mm) 18 35 Beamreceiving part 20.5 6 Beamemitting part 62 Center of sensing 50 2-ø4.5 mounting holes 2-M4 nut seats (on both sides) 4 5 25 ø5.8 cable, 2m long Retroreflective long sensing range type: NX5-RM7□ (Unit: mm) 18 20.5 Center of sensing 35 Beamreceiving part Beamemitting part 6 2-ø4.5 mounting holes 2-M4 nut seats (on both sides) 22 50 62 4 5 25 ø5.
Reflector: RF-230 (Unit: mm) 50.3 59.3 49.3 (30) 10 5 3.3 40 8.3 2-ø4.6 mounting holes Reflector: RF-220 (Unit: mm) 35.3 42.3 34.3 (30) 8 5 25 3.3 8.3 2-ø3.
Reflector: RF-210 (Unit: mm) 33.3 12.8 2-M3 nut inserting hole (For backside mounting) 11 2-ø3.4 through-hole (For side mounting) 3.2 25 10 2-ø3.4 hole depth 6 (For backside mounting) 2-M3 nut inserting hole (For side mounting) Reflective tape: RF-11 (Unit: mm) 30 (28) 8 (6) 0.7 Adhesive tape Reflective tape: RF-12 (Unit: mm) 30 (28) 0.
(MEMO) 25
Please contact .......... ■ Overseas Sales Division (Head Office): 2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan ■ Telephone: +81-568-33-7861 ■ Facsimile: +81-568-33-8591 panasonic.net/id/pidsx/global For sales network, please visit our website. © Panasonic Industrial Devices SUNX Co., Ltd.
