Data Sheet

Certifications/Ratings
Specifications
ELECTRICAL SPECIFICATIONS
Power 24VAC 52 watts (excluding camera) 24VAC 68 watts (camera)
Surge Protector (Video) Clamping differential node voltage between 240-300V and common
mode voltage from 27-36V
Ground Loop Isolator (Optional)
Model No. PWBT1621
60Hz hum rejection 1000V p-p
Bandpass 10Hz to 25MHz
Insertion Loss 0.3dB
MECHANICAL SPECIFICATIONS
Size (HxWxD)
POD9CA/POD9CTA 15” x 11” x 11” (381 x 280 x 280mm)
POD9CWA/PO9CWTA 15” x 11” x 16” (381x 280 x 407mm)
Weight 7Lbs. (3 Kg) (without camera)
Construction
Upper Housing 0.125” (3.2mm) plastic top, 94VO flame rated, and UV protected
Lower Dome Polycarbonate blend (Distortion free)
Mounting Brackets Cast or machined aluminum
ENVIRONMENTAL SPECIFICATIONS
Operating Temperature -40°F to 122°F (-40°C to 50°C)
Heater activates at 60°F (15°C), deactivates at 80°F (27°C), 24VAC, 50W
Blower Continuous operation
Panasonic System Networks Company of America Surveillance, Monitoring and Video Imaging
Design and specifications subject
to change without notice.
06092011
http://panasonic.com/security
Panasonic Service Center
415 Horizon Drive
Suite 350-B
Suwanee, GA 30024
[phone]
Bid Specifications
The outdoor dome camera housing shall be the Panasonic model POD9CA, POD9CWA or equivalent. The housing has been designed for the Unitized Surveillance Device Series WV-CS954/
WVCS574/WV-NS324/WV-N202A. The POD9CA/POD9CTA housings are pendant mounts, and the POD9CWA/POD9CWTA are wall mounted housings. The enclosure is equipped with
24VAC input blowers and thermostatically controlled heaters. The POD9CA housing is manufactured from a high-impact engineered plastic, UV protected, with a UL flame rating of 94V0. The
dome has been made from an injection molded, optically clear, polycarbonate blend material. The dome is held in place with minimum of (3) fasteners, and a safety cable is provided to hold
the dome while servicing. The enclosure is accessible from below with (3) captive fasteners used to press the dome against a sealing O-ring. A twist-off feature allows for the final removal of
the dome. On pendant models all incoming wires enter the unit through the top of the housing. A 1” NPT quick-release coupling is provided at the top of the unit for ease of installation and
quick removal of the unit. On wall mount models all incoming wires enter through the back of the wall mount and run up into the housing. The housing includes a camera mounting bracket that
integrates a heater, blower, video and power surge protector capable of clamping differential node voltage between 240-300V and common mode voltage from 27-36V. The housing is powered
with 24VAC (60Hz) and has a power consumption not to exceed 68W including Unitized Camera. The blower draws 1.6W continuous power. The 50W heater turns on at 60°F (15°C) and
turns off at 80°F (27°C). A ground isolation transformer, Panasonic model PWBT1621, is available as an option. The housing supports a temperature range of -40°F to 120°F (-40°C to 50°C).
Options/Accessories
PWM20G Aluminum gooseneck wall mount, black
PPRM30G Aluminum parapet mount, black
PACA2 Aluminum corner mount adapter, black (must be used with PWM20G)
PAPM3 Aluminum pole mount adapter, black (must be used with PWM20G)
POD9CTA / POD9CWTA
POD9CA / POD9CWA