Specifications

ManualsBrandsPanasonic ManualsProjectorsPT-DS8500

S PEC F ILE

Product Number : PT-DS8500U

Product Name : 3-Chip DLP

Projector

As of July 2010. Specifications subject to change without notice.

SFD10M002

1/17

Summary of content (17 pages)

PAGE 1
S P E C P ro d u c t N u m b e r : PT-DS8500U P ro d u c t N a m e : 3-Chip DLP ® Projector F As of July 2010. Specifications subject to change without notice.
PAGE 2
S P E C F I L E 3-Chip DLP ® Projector PT-DS8500U Specifications Main unit Power supply Power consumption DLP® chip Panel size Display method Pixels Lens Lamp Screen size Brightness* 2 Center-to-corner uniformity* 2 Contrast* 2 Resolution Scanning frequency SDI HDMI/DVI-D/RGB YPBPR (YCBCR) S-Video/Video Optical axis shift Keystone correction range Installation As of July 2010 SFD10M002 120 V AC, 10 A, 60 Hz 920 W (970 VA) (0.2 W with standby mode set to ECO* 1 .
PAGE 3
S P E C F I L E PT-DS8500U 3-Chip DLP ® Projector Terminals * 3 SDI IN HDMI IN BNC × 1, SD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE 259M compliant: 480i, 576i Single-link HD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE 292M compliant: 720/50p, 720/60p, 1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p HDMI 19-pin × 1, Deep Color, compatible with HDCP, 480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p (non-interlaced signals
PAGE 4
S P E C F I L E PT-DS8500U 3-Chip DLP ® Projector Remote control unit Power supply Operation range* 9 Dimensions (W × H × D) Weight Supplied accessories Optional accessories Zoom lens (1.0 – 1.2:1) Zoom lens (1.4– 1.8:1) Zoom lens (1.8– 2.6:1) Zoom lens (2.6– 5.1:1) Zoom lens (5.0– 8.0:1) Zoom lens (7.9– 15.0:1) Fixed-focus lens (0.
PAGE 5
S P E F C I L E PT-DS8500U 3-Chip DLP ® Projector 540 (21-1/4) 548.5 (21-19/32) Dimensions 462 (18-3/16 ) 100 ( 3-15/16 ) 200 (7-7/8 ) 8.5 (11/32) unit : mm (inch) NOTE: This illustration is not drawn to scale.
PAGE 6
S P E C F I L E PT-DS8500U 3-Chip DLP ® Projector (when installed using the ET-PKD310H) ∅60.5 (2-3/8) H Upper edge of projected image *2 340–420 (13-3/8– 16-17/32) *2 436–516 (17-5/32– 20-5/16) Standard setting-up position L * 1 198 342 (7-25/32) (13-15/32) Projected image *1 When the lens protrudes to the maximum.
PAGE 7
S P E C F I L E PT-DS8500U 3-Chip DLP ® Projector Projection distance for 4:3 aspect ratio screen (ET-D75LE6/D75LE10/D75LE20/D75LE30/D75LE4/D75LE8/D75LE5) Unit: millimeters Screen size (inch, diagonal) Distance to screen (L) Zoom ET-D75LE6 Zoom lens ET-D75LE10 Zoom lens ET-D75LE20 Zoom lens ET-D75LE30 Zoom lens Fixed-focus ET-D75LE4 Zoom lens ET-D75LE8 Zoom lens max.
PAGE 8
S P E C F I L E PT-DS8500U 3-Chip DLP ® Projector Projection distance for 4:3 aspect ratio screen (ET-D75LE1/D75LE2/D75LE3) Unit: millimeters Screen size (inch, diagonal) Distance to screen (L) ET-D75LE1 Zoom lens ET-D75LE2 Zoom lens ET-D75LE3 Zoom lens Height from the edge of screen to center of lens (H) min. max. min. max. min. max.
PAGE 9
S P E C F I L E PT-DS8500U 3-Chip DLP ® Projector Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 4:3 Zoom lenses ET-D75LE6 minimum maximum L (mm) = (diagonal screen size in inches) × 20.7 – 56.6 L (mm) = (diagonal screen size in inches) × 24.8 – 73.6 ET-D75LE10 minimum maximum L (mm) = (diagonal screen size in inches) × 29.0 – 85.7 L (mm) = (diagonal screen size in inches) × 37.
PAGE 10
S P E C F I L E PT-DS8500U 3-Chip DLP ® Projector Shift range Optical axis shift function allows to shift the position of a projected image as shown below. • When the lens except the ET-D75LE6 is mounted H 0.5V 0.3H 0.5V 0.1V 0.1V (Height of projected image) V 0.3H (Width of projected image) Standard postition of projected image • When the ET-D75LE6 is mounted H 0.4V 0.4V 0.12V 0.12V V 0.2H (Height of projected image) 0.
PAGE 11
S P E F C I L E PT-DS8500U 3-Chip DLP ® Projector List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning frequencies of 15 to 100 kHz, vertical scanning frequencies of 24 to 120 Hz, and a dot clock of 162 MHz maximum can be input. NOTE: The native resolution of this projector is 1,400 × 1,050 pixels.
PAGE 12
S P E C F I L E PT-DS8500U 3-Chip DLP ® Projector Display mode 1280 × 800 Display resolution (dots)1 1280 x 800 1280 x 800 2 1280 x 800 MSXGA SXGA 1366×768 1280 x 960 1280 × 1024 1280 × 768 SXGA+ 1400 × 1050 WXGA+ 1440 × 900 UXGA60 WSXGA+ 1600 × 1200 1680 × 1050 1920×1080 1920 1920 1920 1920 1920 1920 WUXGA × × × × × × 1080 2 1080 1080 1200 2 1200 1200 Scanning frequency H V (kHz) (kHz) 41.3 49.7 49.3 62.8 71.6 60.0 52.4 64.0 72.3 78.2 80.0 91.1 47.7 39.6 54.1 64.0 65.2 65.3 78.
PAGE 13
S P E F C I L E PT-DS8500U 3-Chip DLP ® Projector Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below. Pin assignments and signal names No. Signal name Description 1 NC No.
PAGE 14
S P E C F I L E PT-DS8500U 3-Chip DLP ® Projector Cable specifications Projector 1 PC (DTE) NC NC 2 2 3 3 4 NC NC NC NC 6 7 7 8 8 9 4 5 5 6 1 NC NC 9 Control commands * Command : Parameter Function PON POF IIS:SDI IIS:HD1 IIS:DVI IIS:RG1 IIS:RG2 IIS:VID IIS:SVD LPM:0 LPM:1 OSH:0 OSH:1 OPP:0 OPP:1 OPP:2 OPP:3 OAS VPM:NA T VPM: STD VPM:DYN VPM:CIN VPM:GRA VPM:DIC VXX:DLVI0=+00000 VXX:DLVI0=+00001 VXX:DLVI0=+00002 VXX:DLVI0=+00003 OTE:4 OTE:9 OTE:10 OTE:p1p2p3p4 TSD:y1y2y3y4
PAGE 15
S P E C F I L E PT-DS8500U 3-Chip DLP ® Projector Status asking commands Command : Parameter QPW Function Main power status QSH Shutter function status QFZ Freeze function status QIN Input signal status QOS On-screen display status QST Q$L:1 Q$L:2 QSL Projector run time Lamp 1 run time Lamp 2 run time Lamp operation mode status QLP Lamp power mode status QPM Picture mode status QVX:DLVI0 System daylight view status QPP P in P status QTM:0 QTM:1 QTM:2 QGD QGT Temperature status
PAGE 16
S P E F C I L E PT-DS8500U 3-Chip DLP ® Projector Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. 1. Never place objects on top of the projector while it is operating. 2. Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector’s exhaust openings. 3. Do not stack projector units directly on top of one another.
PAGE 17
S P E C F I L E 3-Chip DLP ® Projector PT-DS8500U Operating the projector continuously 1. If the projector is to be operated continuously 24 hours a day, use the dual-lamp optical system’s alternating lamp operation (lamp changer) function. The projector cannot be operated continuously 24 hours a day in dual-lamp mode. Allow a minimum of two hours per day of non-operation time. 2. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.