S P E C F I L E The PT-DW17K is not equipped with a lens. P ro d u c t N u m b e r : PT-DW17K P ro d u c t N a m e : 3-Chip DLP ™ Projector As of September 2012. Specifications and appearance are subject to change without notice.
S P E C F I L E PT-DW17K 3-Chip DLP ™ Projector Specifications Main unit Power supply Power consumption DLP™ chip Panel size Display method Pixels Lens Lamp Screen size Brightness* 2 Center-to-corner uniformity* 2 Contrast* 2 Resolution Scanning frequency HDMI/DVI-D RGB YPBPR (YCBCR) Video/S-Video Optical axis shift Vertical Horizontal 200 – 240 V AC, 12 A, 50/60 Hz (3-wire single-phase) 2,300 W (2,350 VA) (0.3 W with STANDBY MODE set to ECO.* 1 9 W with STANDBY MODE set to NORMAL .), max.
S P E C F I L E PT-DW17K 3-Chip DLP ™ Projector Terminals HDMI IN HDMI 19-pin × 1, Deep Color, compatible with HDCP, 480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p VGA (640 × 480) – WUXGA*4 (1,920 × 1,200), dot clock: 25 MHz –162 MHz NOTE: Compatible with non-interlaced signals only. DVI-D IN DVI-D 24-pin × 1, DVI 1.
S P E C F I L E PT-DW17K 3-Chip DLP ™ Projector Remote control unit Power supply Operation range* 9 Dimensions (W × H × D) Weight 3 V DC (AA type battery × 2) Approx. 30 m (98 ft 5 in) when operated from directly in front of the signal receptor 51 × 176 × 28 mm (2 × 6-15/16 × 1-3/32 inches) Approx. 134 g (4.
S P E F C I L E PT-DW17K 3-Chip DLP ™ Projector 80 0 ( 31-1/ 2 ) 730 ( 28 -3 /4 ) Dimensions 36 (1-13 / 32 ) 244 244 ( 9 -19 / 32 ) ( 9 -19 / 32 ) 620 ( 24-13 / 32 ) 177 ( 6 -31/ 32 ) 291 (11-15 / 32 ) 70 ( 2-3 /4 ) unit : mm (inch) NOTE: This illustration is not drawn to scale.
S P E C F I L E PT-DW17K 3-Chip DLP ™ Projector H Upper edge of projected image 2 ∅60.5 (2-3/8) 560– 680* (22-1/16– 26-25/32) 419– 539* (16-1/2– 21-7/32) 2 Standard setting-up position *1 When the lens protrudes to the maximum.
S P E C F I L E PT-DW17K 3-Chip DLP ™ Projector Projection distance for 16:9 aspect ratio screen (ET-D75LE6/D75LE10/D75LE20/D75LE30/D75LE40/D75LE8/D75LE50) Unit: meters Screen size (diagonal) Distance to screen (L) Zoom Fixed-focus Height from the edge of screen to center of lens (H) Zoom lenses FixedET-D75LE8 ET-D75LE50 focus Zoom lens Fixed-focus Except ET-D75LE6 lens lens ET-D75LE6 min. max.
S P E C F I L E PT-DW17K 3-Chip DLP ™ Projector Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 16:9 Zoom lenses ET-D75LE6 minimum maximum L (m) = (diagonal screen size in inches) × 0.0231 – 0.0566 L (m) = (diagonal screen size in inches) × 0.0277 – 0.0736 ET-D75LE10 minimum maximum L (m) = (diagonal screen size in inches) × 0.0324 – 0.
S P E F C I L E PT-DW17K 3-Chip DLP ™ Projector Shift range Optical axis shift function allows to shift the position of a projected image as shown below. • When the lens except the ET-D75LE6 is mounted • When the ET-D75LE6 is mounted H H 0.3H 0.2H 0.6V 0.2V 0.2V 0.7V V (Height of projected image) 0.2V 0.2V (Width of projected image) 0.6V 0.2H 0.7V (Width of projected image) (Height of projected image) V 0.
S P E C F I L E PT-DW17K 3-Chip DLP ™ Projector List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning frequencies of 15 kHz to 100 kHz, vertical scanning frequencies of 24 Hz to 120 Hz, and a dot clock of 162 MHz maximum can be input. NOTE: The native resolution of this projector is 1,366 × 768 pixels.
S P E C F I L E PT-DW17K 3-Chip DLP ™ Projector Display mode Display resolution (dots) 1280 × 720 1280 × 720 1280 × 768 1280 × 768 1280 × 768 * 1280 × 768 1280 × 800 1280 × 800 1280 × 800 * 1280 × 800 MSXGA SXGA 1366×768 1280 × 768 SXGA+ 1400 × 1050 WXGA+ 1440 × 900 UXGA60 WSXGA+ 1600 × 1200 1680 × 1050 1920×1080 1920 1920 1920 1920 1920 1920 WUXGA * 1280 × 960 1280 × 1024 × × × × × × 1080 1080 * 1080 1200 1200 * 1200 Scanning frequency H V (kHz) (kHz) 37.1 44.8 76.3 92.
S P E F C I L E PT-DW17K 3-Chip DLP ™ Projector Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below. Pin assignments and signal names 6 No. 1 2 3 4 5 9 1 5 Signal name – TXD RXD – GND Description NC Send data Receive data Connected internally Ground No.
S P E C F I L E PT-DW17K 3-Chip DLP ™ Projector Cable specifications Projector 1 PC (DTE) NC NC 2 2 3 3 4 NC NC NC NC 6 7 7 8 8 9 4 5 5 6 1 NC NC 9 Control commands * Command : Parameter Function PON POF IIS:HD1 IIS:DVI IIS:RG1 IIS:RG2 IIS:VID LPM:0 LPM:1 LPM:2 LPM:3 LPM:4 LPM:5 LPM:6 LPM:7 LPM:8 LPM:9 LPM:10 LPM:11 LPM:12 LPM:13 OSH:0 OSH:1 OPP:0 OPP:1 OPP:2 OPP:3 OAS VPM:NAT VPM:STD VPM:DYN VPM:CIN VPM:GRA VPM:DIC VXX:DLVI0=+0 0000 VXX:DLVI0=+0 0001 VXX:DLVI0=+0 0002 VX
S P E C F I L E PT-DW17K 3-Chip DLP ™ Projector Status request commands Command : Parameter QPW Function Main power status QSH Shutter function status QFZ Freeze function status QIN Input signal status QOS On-screen display status QST Q$L:1 Q$L:2 Q$L:3 Q$L:4 QSL Projector run time Lamp 1 run time Lamp 2 run time Lamp 3 run time Lamp 4 run time Lamp operation mode status QPM Picture mode status QVX:DLVI0 System daylight view status QPP P in P status QTM:0 QTM:1 QTM:2 QGD QGT Tempe
S P E C F I L E PT-DW17K 3-Chip DLP ™ Projector Command example To set the on-screen display off, send the command as shown below. STX Start ADZZ ; OOS ID Address : Command 0 ETX Parameter End NOTE: When sending commands without parameters, a colon (:) is not necessary. Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. 1.
S P E C F I L E 3-Chip DLP ™ Projector PT-DW17K Direction of air intake and exhaust Intake Exhaust Operating the projector continuously 1. If the projector is to be operated continuously one week, use the quad-lamp optical system’s alternating lamp operation (lamp relay) function. The projector cannot be operated continuously one week in quadlamp mode. Allow a minimum of two hours per day of non-operation time for each lamp if the projector is to be operated continuously for more than one week.
