Specifications

S P E C F I L E
PT-DZ21K
3-Chip DLP
™
Projector
As of May 2012
SFD12M005
3 / 1 9
Optical axis shift Vertical
Horizontal
Keystone correction range
Keystone correction range when using the
optional upgrade kit ET-UK20*
3
Installation
Terminals SDI IN 1
SDI IN 2
HDMI IN
DVI-D IN
RGB 1 IN
R, G, B
Y, P
B, PR (Y, CB, CR)
S-Video signal
RGB 2 IN
R, G, B
Y, PB, PR (Y, CB, CR)
VIDEO IN
3D SYNC 1 IN/OUT
3D SYNC 2 OUT
SERIAL IN
SERIAL OUT
REMOTE 1 IN
REMOTE 1 OUT
±55% (±44% with the ET-D75LE6) from center of screen, powered
±20% (±15% with the ET-D75LE6) from center of screen, powered
NOTE: Optical axis shift function cannot be operated when used with the
ET-D75LE50.
Vertical ±40°, horizontal ±15°
(vertical ±22° and horizontal ±15° with the ET-D75LE50,
vertical ±28° and horizontal ±15° with the ET-D75LE6)
Vertical ±45°, horizontal ±40°
(vertical ±22° and horizontal ±15° with the ET-D75LE50,
vertical ±28° and horizontal ±15° with the ET-D75LE6,
vertical ±40° and horizontal ±40° with the ET-D75LE10/D75LE20)
Ceiling/floor, front/rear
BNC × 1,
Dual-link HD-SDI signal: SMPTE ST 372 compliant (Link-A)
3G-SDI signal: SMPTE ST 424 compliant
HD-SDI signal: SMPTE ST 292 compliant
SD-SDI signal: SMPTE ST 259 compliant
BNC × 1,
Dual-link HD-SDI signal: SMPTE ST 372 compliant (Link-B)
HD-SDI signal: SMPTE ST 292 compliant
SD-SDI signal: SMPTE ST 259 compliant
HDMI 19-pin × 1, Deep Color, compatible with HDCP,
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p,
1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p
VGA (640 × 480) – WUXGA*
4
(1,920 × 1,200),
dot clock: 25 MHz–162 MHz
NOTE: Compatible with non-interlaced signals only.
DVI-D 24-pin × 1, DVI 1.0 compliant, HDCP compatible,
for single link only
480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/24p,
1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p,
VGA (640 × 480) – WUXGA*
4
(1,920 × 1,200),
dot clock: 25 MHz–162 MHz
NOTE: Compatible with non-interlaced signals only.
BNC ×5
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms
Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms
D-sub HD 15-pin (female) ×1
R: 0.7 Vp-p, 75 ohms,
G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms,
B: 0.7 Vp-p, 75 ohms
HD, VD/SYNC: TTL, high impedance, positive/negative automatic
NOTE: SYNC/HD and VD terminals do not accept tri-level sync signals.
Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms
BNC × 1, 1.0 Vp-p, 75 ohms
BNC × 1, 1.0 Vp-p, 75 ohms
Input: TTL, high impedance. Output: TTL, max. 10 mA
BNC × 1, 1.0 Vp-p, 75 ohms, TTL, max. 10 mA
D-sub 9-pin (female) × 1 for external control (RS-232C compliant)
D-sub 9-pin (male) × 1 for link control
M3 jack × 1 for wired remote control
M3 jack × 1 for link control