S P E C F I L E The PT-EZ570L is not equipped with a lens. P ro d u c t N u m b e r : PT-EZ570/EZ570L P ro d u c t N a m e : LCD Projectors As of July 2012. Specifications and appearance are subject to change without notice.
S P E C F I L E PT-EZ570/EZ570L LCD Projectors Specifications Main unit Power supply Power consumption Optical system LCD panel Lens Panel size Display method Pixels Pixel configuration PT-EZ570 PT-EZ570L Lamp Screen size Brightness* 2 Center-to-corner uniformity* 2 Contrast* 2 Resolution Scanning frequency HDMI/DVI-I RGB YPBPR (YCBCR) Video/S-Video Optical axis shift 100 – 240 V AC, 50/60 Hz 490 W (492 VA) (0.4 W with STANDBY MODE set to ECO* 1 , 11 W with STANDBY MODE set to NETWORK .
S P E C F I L E PT-EZ570/EZ570L LCD Projectors Terminals INPUT 1 HDMI IN DVI-D IN RGB IN R, G, B Menu selection HDMI 19-pin × 1, Deep Color, HDCP compatible 480p (525p), 576p (625p), 720 (750)/60p, 720 (750)/50p, 1035/60i, 1080 (1125)/60i, 1080 (1125)/50i, 1080/25p, 1080/25sF, 1080/24p, 1080/24sF, 1080/30p, 1080/30sF, 1080/60p, 1080/50p, VGA (640 × 480) – WUXGA* 2 (1,920 × 1,200) Audio signal: linear PCM (sampling frequencies: 48 kHz, 44.1 kHz, 32 kHz) DVI-D 24-pin × 1, DVI 1.
S P E C F I LCD Projectors Operation noise* 2 Operating temperature Operating humidity Remote control unit Power supply Operation range* 5 Dimensions (W × H × D) Weight L E PT-EZ570/EZ570L 37 dB (LAMP POWER: NORMAL), 31 dB (LAMP POWER: ECO 1 / ECO 2) 0–40 °C (32–104 °F) up to 1,000 m (3,280 ft) above sea level, with fan control set to OFF, 0–30 °C (32–86 °F) between 1,000 m and 2,000 m (3,280 ft and 6,561 ft) above sea level, with fan control set to ON 1, 0–30 °C (32–86 °F) between 2,000 m and 2,7
S P E F C I L E PT-EZ570/EZ570L LCD Projectors 9 (11/32) 164 ( 6-15/32) 155 ( 6-3/32) 370 (14-9/16 ) 345 (13-19/32) unit : mm (inch) NOTE: This illustration is not drawn to scale. The illustration shows the PT-EZ570. 64 (2-17/32) 434 (17-3/32) Dimensions 412 (16-7/32) 489.
S P E C F I L E PT-EZ570/EZ570L LCD Projectors H ∅54 ( 2-1/8 ) Upper edge of projected image 951–1,551* 2 ( 37-7/16 – 61-1/16 ) * 2 860 –1,460* 2 ( 33-27/32– 2 57-15/32)* Standard setting-up position *1 When the lens protrudes to the maximum. A: 83.5 mm (3-9/32 in) with the ET-ELW20 64 mm (2-17/32 in) with the supplied lens 88 mm (3-15/32 in) with the ET-ELT20 84 mm (3-5/16 in) with the ET-ELT21 54 mm (2-1/8 in) with the ET-ELW21 *2 Adjustable in 30 mm (1-3/16 in) steps.
S P E C F I L E PT-EZ570/EZ570L LCD Projectors Projection distance for 16:10 aspect ratio screen Unit: meters Distance to screen (L) Screen size (diagonal) Zoom ET-ELW20 Zoom lens [m] Supplied lens Fixed-focus ET-ELT20 Zoom lens ET-ELT21 Zoom lens Height from the edge of screen to center of lens (H) ET-ELW21 Fixed-focus lens Zoom lenses Fixedfocus lens [in] min. max. min. max. min. max min. max. 1.02 / 40 1.02 1.41 1.36 2.35 2.29 3.81 3.72 6.03 0.63 -0.05 – 0.59 0.
S P E C F I L E PT-EZ570/EZ570L LCD Projectors Projection distance for 16:9 aspect ratio screen Unit: meters Distance to screen (L) Screen size (diagonal) Zoom ET-ELW20 Zoom lens [m] Supplied lens Fixed-focus ET-ELT20 Zoom lens ET-ELT21 Zoom lens Height from the edge of screen to center of lens (H) ET-ELW21 Fixed-focus lens Zoom lenses Fixedfocus lens [in] min. max. min. max. min. max min. max. 1.02 / 40 1.05 1.45 1.40 2.42 2.36 3.92 3.83 6.20 0.65 -0.05 – 0.55 0.
S P E C F I L E PT-EZ570/EZ570L LCD Projectors Calculation of the projection distance For a screen size different from the above, use the equation below to calculate the projection distance. Aspect ratio 16:10 ET-ELW20 minimum maximum L (m) = (diagonal screen size in inches) × 0.026816 - 0.055497 L (m) = (diagonal screen size in inches) × 0.036511 - 0.053400 Supplied lens minimum maximum L (m) = (diagonal screen size in inches) × 0.035305 - 0.
S P E C F I L E PT-EZ570/EZ570L LCD Projectors Shift range Optical axis shift function allows to shift the position of a projected image as shown below. H (Width of projected image) 0.1H Standard postition of projected image 0.6V V (Height of projected image) 0.6V 0.1H • The ET-ELW21 is a fixed short-focus lens. Therefore, the lens shift function provided in the main unit cannot be used. Installable angle Install the projector at an angle within the range shown below.
S P E F C I L E PT-EZ570/EZ570L LCD Projectors List of compatible signals The signals that can be input to this projector are shown in the table below. Horizontal scanning frequencies of 15 kHz to 100 kHz (15 kHz to 120 kHz for RGB signals), vertical scanning frequencies of 24 Hz to 120 Hz (48 Hz to 100 Hz for RGB signals), and a dot clock of 162 MHz maximum (230 MHz maximum for RGB signals) can be input. NOTE: The native resolution of this projector is 1,920 × 1,200 pixels.
S P E C F I L E PT-EZ570/EZ570L LCD Projectors Display mode WXGA Display resolution (dots)*1 1280 × 768 1280 × 800 1360 × 768 MAC21 SXGA 1366 1376 1152 1152 × × × × 768 768 870 900 1280 × 960 1280 × 1024 1280 × 1024i MAC SXGA+ 1280 × 960 1280 × 1024 1400 × 1050 WXGA+ 1440 × 900 UXGA UXGA* 2 1600 × 1200 WSXGA+ WUXGA WUXGA* 2 1680 × 1050 1920 × 1200 Scanning frequency H V (kHz) (kHz) 47.8 60.3 68.6 41.2 49.6 49.7 58.3 56.0 57.7 60.0 62.8 64.0 71.6 47.7 56.2 46.5 48.4 68.7 64.2 61.
S P E F C I L E PT-EZ570/EZ570L LCD Projectors Serial connector The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below. Pin assignments and signal names 6 No. 1 2 3 4 5 9 1 5 Signal name – TXD RXD – GND Description NC Transmitted data Received data Connected internally Ground No.
S P E C F I L E PT-EZ570/EZ570L LCD Projectors Cable specifications Projector 1 PC (DTE) NC NC 2 2 3 3 4 1 4 NC NC 6 NC NC 6 7 NC NC 7 8 NC NC 8 9 NC NC 9 5 5 Control commands * Command : Parameter Function PON POF IIS:HD1 IIS:DVI IIS:RG1 IIS:RG2 IIS:CP1 IIS:VD1 IIS:CP2 IIS:SVD IIS:VD2 OLP:2 OLP:0 OLP:3 OLP:4 OSH:0 OSH:1 OFZ:1 OFZ:0 OAS VSE:0 VSE:6 VSE:2 VSE:40 VSE:5 VSE:50 VPM:STD VPM:DYN VPM:CIN VPM:REA Standby power Input selection Lamp power Shutter Freeze
S P E C F I L E PT-EZ570/EZ570L LCD Projectors Status request commands Command : Parameter Q PW Function Main power status Q IN Input signal status Q LP Lamp power mode status Q SH Shutter function status Q FZ Freeze function status Q SE Aspect mode status Q PM Picture mode status Q ST Q $L:1 Q TM:0 Q TM:2 Projector run time Lamp run time Temperature status Callback 000 001 HD1 DVI RG1 RG2 CP1 VD1 CP2 SVD VD2 2 0 3 4 0 1 0 1 0 6 2 40 5 50 0 6 STD DYN CIN REA p1p2p3p4p5 p1p2p3p4 p1p2
S P E C F I L E PT-EZ570/EZ570L LCD Projectors Notes on projector placement and operation The projector uses a high-wattage lamp that becomes very hot during operation. Please observe the following precautions. 1. Never place objects on top of the projector. 2. Make sure there is an unobstructed space of 1,000 mm (3 feet 3 inches) or more around the projector’s exhaust openings. 3. Do not stack projector units directly on top of one another for the purpose of multiple (stacked) projection.
S P E C F I L E LCD Projectors PT-EZ570/EZ570L Operating the projector continuously 1. If the projector is to be operated continuously 12 hours or more, lamp replacement cycle duration becomes shorter. 2. The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods. Weights and dimensions shown are approximate. Specifications and appearance are subject to change without notice. Product availability differs depending on region and country.
