User's Manual
Table Of Contents
- Read this first!
- Chapter 1 Preparation
- Chapter 2 Getting Started
- Chapter 3 Basic Operations
- Switching on/off the projector
- Projecting
- Operating with the remote control
- Using the shutter function
- Using the mute function
- Adjusting the volume
- Using the freeze function
- Using the on-screen display function
- Using the auto setup function
- Using the screen adjustment function
- Using the digital zoom function
- Switching the image aspect ratio
- Using the presentation timer function
- Using the FUNCTION button
- Displaying internal test pattern
- Using the status function
- Using the ECO management function
- Setting the ID number on the remote control
- Chapter 4 Settings
- Chapter 5 Operation of Function
- Chapter 6 Maintenance
- Chapter 7 Appendix
r Connecting terminals
1
5
1110
6
2
3 7
8
9
4
1 <USB (VIEWER/WIRELESS/DC OUT)> terminal
When using the Memory Viewer function, attach the USB
memory directly to this terminal. (x page 101)
Attach the wireless module (Model No.: AJ-WM50) directly to this
terminal when using the wireless LAN function. (x page 106)
In addition, this terminal can be used for power supply (DC 5 V,
maximum 2 A).
2 <VIDEO IN> terminal
This is the terminal to input video signals.
3 <COMPUTER 1 IN> terminal
This is the terminal to input RGB signals or YC
B
C
R
/YP
B
P
R
signals.
4 <COMPUTER 2 IN/1 OUT> terminal
This is the terminal to input RGB signals or YC
B
C
R
/YP
B
P
R
signals.
It can also output the signals input from <COMPUTER 1 IN>
terminal to an external device.
5 <HDMI 1 IN> terminal / <HDMI 2 IN> terminal
These are the terminals to input HDMI signal.
6 <LAN> terminal
This is the LAN terminal to connect to the network.
This also supports the image transfer from the image transfer
application software.(x page 104)
7 <DIGITAL LINK/LAN> terminal
(Not available for PT-VMZ40)
This is a terminal to connect a device that transfer video
signal or audio signal. Also, this is the LAN terminal to connect to
the network.
8 <AUDIO IN 1> terminal / <AUDIO IN 2> terminal
These are the terminals to input audio signals.
9 <AUDIO IN 3> terminal
This is the terminal to input audio signals.
Left input <L> and right input <R> are provided for the <AUDIO
IN 3> terminal.
10 <VARIABLE AUDIO OUT> terminal
This is the terminal to output the input audio signal.
11 <SERIAL IN> terminal
This is the RS-232C compatible terminal to externally control the
projector by connecting a computer.
Attention
f When the [PROJECTOR SETUP] menu → [ECO MANAGEMENT] → [STANDBY MODE] is set to [NORMAL], the <USB (VIEWER/
WIRELESS/DC OUT)> terminal can supply power even in standby state. If set to [ECO], the <USB (VIEWER/WIRELESS/DC OUT)>
terminal can not supply power in standby state.
f When an external device exceeding the rating (DC 5 V, maximum 2 A) is connected to the <USB (VIEWER/WIRELESS/DC OUT)> terminal,
an error is detected and the power supply will be stopped. At this time, disconnect the external device, cut off the power of the projector and
then reconnect the power plug to the outlet.
f When a LAN cable is directly connected to the projector, the network connection must be made indoors.
The signal may deteriorate due to the effect of noise or cable length.
f The <DIGITAL LINK/LAN> terminal and the <LAN> terminal are connected inside the projector. When using both the <DIGITAL LINK/
LAN> terminal and the <LAN> terminal, congure the system to prevent them from being connected to the same network directly or via the
peripheral devices such as a hub or twisted-pair-cable transmitter.
28 - ENGLISH
Chapter 1 Preparation - About your projector