User's Manual
Table Of Contents
- Read this first!
- Chapter 1 Preparation
- Chapter 2 Getting Started
- Chapter 3 Basic Operations
- Switching on/off the projector
- Projecting
- Operating with the remote control
- Using the shutter function
- Using the mute function
- Adjusting the volume
- Using the freeze function
- Using the on-screen display function
- Using the auto setup function
- Using the screen adjustment function
- Using the digital zoom function
- Switching the image aspect ratio
- Using the presentation timer function
- Using the FUNCTION button
- Displaying internal test pattern
- Using the status function
- Using the ECO management function
- Setting the ID number on the remote control
- Chapter 4 Settings
- Chapter 5 Operation of Function
- Chapter 6 Maintenance
- Chapter 7 Appendix
[AMBIENT LIGHT
DETECTION]
Perform the setting of the ambient light detection. When enabled, the power of the light source can be
adjusted according to the ambient brightness of the installation location.
[SIGNAL DETECTION]
Perform the setting of the signal detection. When enabled, the power of the light source can be
reduced when no signal is detected.
6) Press qw to switch the item.
f The items will switch each time you press the button.
[ON]
Enables the selected function.
[OFF]
Disables the selected function.
Note
f When [AUTO POWER SAVE] is set to [OFF], settings of [AMBIENT LIGHT DETECTION] and [SIGNAL DETECTION] are unavailable.
f The luminance may not be detected correctly when an object is placed on top of the projector, blocking the luminance sensor. In such a
case, it may not operate properly even if [AMBIENT LIGHT DETECTION] is set to [ON].
Setting [LIGHT POWER]
1) Press as to select [ECO MANAGEMENT].
2) Press the <ENTER> button.
f The [ECO MANAGEMENT] screen is displayed.
3) Press as to select [LIGHT POWER].
4) Press qw to switch the item.
f The items will switch each time you press the button.
[NORMAL]
Select this item when high luminance is required. The light power is 100 % and the estimated runtime
is approximately 20 000 hours
*1
.
[ECO]
The luminance will decrease compared to [NORMAL], but select this item to suppress the reduction in
luminance against the runtime of the light source. The light power is 70 % and the estimated runtime
is approximately 24 000 hours
*1
.
[QUIET]
Select this item to prioritize the operation with low noise. The light power is 70 % and the estimated
runtime is approximately 20 000 hours
*1
.
[USER]
Select the item to set the picture brightness as desired.
*1 The foregoing time is a rough estimate when the projector is used without changing the settings of [LIGHT POWER], and will vary depending
on individual differences and usage conditions.
f Proceed to Step 5) when [USER] is selected.
5) Press as to select [LIGHT OUTPUT].
6) Press qw to adjust.
Operation
Adjustment
Range of adjustment
Brightness Runtime (estimate)
Press w.
The screen becomes brighter. The runtime becomes shorter.
50 %
*1
- 100 %
Press q.
The screen becomes darker. The runtime becomes longer.
*1 It should be noted that the picture quality tends to deteriorate as the light output decreases.
Note
f Under inuences of characteristics of each light source, conditions of use, installation environment, etc., the runtime may be shorter than the
estimation.
f Runtime is a time until the luminance of the light source to become about half when using the projector continuously. The runtime is just an
estimate, and is not the warranty period.
f If the runtime exceeds 10 000 hours, replacement of the components inside the projector may be required. Consult your dealer for details.
Setting [POWER MANAGEMENT]
This is a function to set the power of the projector to standby state or ready state automatically when there
is no input signal for specic time. Selection of standby state or the ready state, and the time for the power
management function to operate can be set.
1) Press as to select [ECO MANAGEMENT].
ENGLISH - 85
Chapter 4 Settings - [PROJECTOR SETUP] menu