Initial Setup DVD/VCR DECK Operating Instructions Model No. PV-D4745 / PV-D4745S Basic Operation VCR Operation DVD Operation For Your Information Connections and Initial Setup Procedures are on pages 12 to 17. MULTI FORMAT PLAYBACK *Ability to play back may depend on recording conditions. For assistance, please call : 1-800-211-PANA(7262) or, contact us via the web at:http://www.panasonic.com/contactinfo PV-D4745S P1-25 (041224).
Important Safeguards and Precautions TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, INJURY TO PERSONS OR DAMAGE TO THIS PRODUCT, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE PRODUCT. INSTALLATION OUTDOOR ANTENNA INSTALLATION 1 POWER SOURCE CAUTION Operate only from a power source indicated on the unit or in this manual. If necessary, have your Electric Utility Service Company or Video Products Dealer verify the power source in your home.
Safety Precautions/Mesures de sécurité To prevent fire or shock hazard, do not expose this equipment to rain or moisture. To prevent electric shock, match wide blade of plug to wide slot, fully insert. AVERTISSEMENT: Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas exposer cet appareil à la pluie ou à une humidité excessive. ATTENTION : Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond.
Before Using Congratulations Head Cleaning on your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your DECK. • Date of Purchase • Dealer Purchased From • Dealer Address • Dealer Phone No. • Model No. • Serial No.
Table of Contents Basic Operation For Your Information DVD Operation Disc Operation .................................................................. 36 ~ 41 DVD-RAM Operation (DVD-RAM only) .................................... 42, 43 DVD Operation using On-Screen Displays .................... 44 ~ 48 MP3/JPEG Playback Operation ....................................... 49 ~ 51 Settings for DVD Operation ............................................. 52 ~ 55 A/V OPTIMIZER ..................................
DECK & Cassette Information Prevent Accidental Tape Erasure DVD-RAM discs DVD-RAM discs must meet the following conditions for this unit to be able to play them. Break off the tab to prevent recording. Type Record Tab Screw driver Capacity • Non-cartridge discs • Discs that can be removed from their cartridges (TYPE 2 and 4) • 12 cm (5”) 9.4 GB (double-sided) and 4.7 GB (single-sided) • 8 cm (3”) 2.
Input/Output Terminal: Input Terminal: Output Terminal: Operating Temperature: Operating Humidity: Weight: Dimensions: Discs Played (1) DVD-Video Disc DVD-RAM Disc 120 V AC, 60 Hz Power On: Approx. 22 watts, Power Off: Approx. 0.
Location of Controls Remote Control Bold: VCR Function / Bold Italic: VCR and DVD Functions Italic: DVD Function / Normal: Others VCR/TV EJECT / OPEN / CLOSE p. 21 pp. 20, 22 TV mode p. 28 POWER CHANNEL / / TRACKING / V-LOCK / 10 pp. 4, 21, 22 NUMBER keys VOLUME + / - p. 28 MENU / PLAY LIST ADD/DELETE / CLEAR p. 41, 43 pp. 19, 38, 40 ACTION SELECT pp. 18, 52 SET DVD mode p. 28 VCR mode p. 28 PLAY pp. 20, 22 STOP pp. 20, 22 SKIP+ SKIP- REWIND / SEARCH / SLOW- p. 23 pp.
If the disc cannot be removed... First, unplug DECK. Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc. Bold: VCR Function Italic: DVD Function Bold Italic: VCR and DVD Functions Normal: Others Initial Setup Front View of DECK PLAY p. 20 STOP/EJECT Over 2 inches p.
Location of Controls (continued) Bold: VCR Function Italic: DVD Function Bold Italic: VCR and DVD Functions Rear View of DECK AC Power Plug VHF/UHF Antenna Output Terminal p.12 • While plugged into an AC outlet, this DECK consumes 0.9 W of electrical power in off mode. VHF/UHF Antenna Input Terminal p. 12 Component Video Output Connector (Y, PB, PR) (DVD Only) p. 13 Video Output Connector p. 12 • Optical Digital Audio Output Connector (DVD Only) p. 15 • Video Input Connector p.
On Screen Displays / Light-up Indicators Function & Channel Displays Initial Setup On Screen Displays (VCR) Blank Tape/ No Signal Indications Whenever a blank section of a tape comes When a function button up in Play mode, or when the selected is pressed, e.g. PLAY, channel has no broadcast signal with Weak or you change channels, Signal Display Feature (p. 33) set to OFF, and also if a cassette is the TV screen will turn solid blue. inserted, a 5-second display appears.
Connections Basic Connections • If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher quality picture and sound. • You can enjoy stereo sound even if your TV is not stereo by connecting a stereo amplifier to DECK. • Connect DECK and TV with an RF Coaxial Cable a (supplied) or an AV Cable b (not supplied) as shown in the figure below.
You Can ■ With a Cable Box (DECK Cable Box TV) DVD/VCR DECK ANT or CATV TV IN 1 OUT IN FROM ANT. IN Cable Box VHF/UHF OUT TO TV IN VHF/ UHF OUT R L • view any (including scrambled) channel. • use Remote Control to select channels without using Multi-brand control feature.
Connections (continued) Audio Connections Ready Checklist Turn down the volume, then turn DECK, as well as other equipment to be connected, off before proceeding with connection. Do not block ventilation holes of any of the equipment and arrange them so that air can circulate freely. Read through the instructions before connecting other equipment. Ensure that you observe the color coding when connecting audio and video cables.
When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital bitstream or DTS bitstream is output from the DECK OPTICAL digital audio output connector. When DECK is connected to a Dolby Digital decoder or DTS decoder, you can enjoy theater-quality audio in your home. [An optical digital audio cable (optional) is required when an optional Dolby Digital decoder or DTS decoder is used.] Initial Setup ■ Connecting Amplifier (5.
Initial Setup for Basic Connections (Ready to Play) Before doing Initial Setup 1 Turn TV on. 2 See connections RF Coaxial Cable Connection and ÖSet TV to channel 3. ÖSet TV to VIDEO. 3 AV Cable Connection on page 12. [DECK ➛ TV] • Go to “Initial Setup (Ready to Play).” (See below.) [Cable Box ➛ DECK ➛ TV], [DSS ➛ DECK ➛ TV] • Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel in your time zone.
dy to Play) *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Settings are made automatically. When complete, this screen appears. EJECT Initial Setup 3 If “AUTO CLOCK SET IS INCOMPLETE” appears, manually set clock (below). ACTION SELECT SET VCR Manual Clock Set If Auto Clock Set was incomplete. STOP/EJECT 1 Press ACTION* on remote to display CLOCK screen. 2 Press to select the month and SET to set.
Reset Language, Channels, Clock, 1 2 Press ACTION* to display MENU. Language • PROGRAM functions are not available when using COMPONENT Video Output and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROGRAM. Channels Clock 1) Press to select language item. 1) Press to select “SET UP CHANNEL,” and press SET. 1) Press to select “SET CLOCK,” and press SET. 2) Press SET repeatedly to change language item as shown below.
k, VCR’s Output Channel POWER *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. NUMBER keys CH ADD/DLT ACTION SELECT VCR’s Output Channel 1) Press to select “SET CLOCK,” and press SET. 1) Press to select “VCR’S OUTPUT CH.,” and press SET. 2) Press to select “TIME ZONE ADJUST,” 2) Press SET. SET VCR Basic Operation Time Zone Adjust (Only when Auto Clock is set.
Playback/ Record on a Tape Ready Checklist EJECT VCR/TV All connections are made. (pp. 12 ~ 15) TV and DECK are plugged in. TV is on and tuned to CH 3, 4, or VIDEO. Remote is in VCR mode. (Press VCR.) (➛ The VCR mode Light-up Indicator lights on DECK) CH / Playback a Tape 1 2 Insert a tape. • DECK power comes on. If Auto VCR/TV (see p. 34) is set to “OFF,” press VCR/TV on the remote for VCR mode. Press PLAY* to play a tape. VCR FF/ SLOW+ DVD PLAY STOP • If tape has no rec. tab (p.
*Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Record on a Tape 1 Press CH , or NUMBER keys to select the channel. • If channel number is over 100, first press 100 key then the other 2 digits. • For “LINE” input, see p. 35. 3 Press SPEED to select the record speed (p. 4). Note Remove loose or peeling labels from tapes to prevent tape jam. SP = Standard Play SLP = Super Long Play 4 Press REC to start recording.
Basic DVD Operation Ready Checklist All connections are made. (pp. 12 ~ 15) DECK is plugged in. If DECK is connected to an audio amplifier, turn the stereo system’s power on. OPEN/ CLOSE 1 Press DVD to select DVD mode. 2 Press OPEN/CLOSE *, and then place a disc into the disc tray. • The DVD mode Light-up Indicator lights on DECK. • If a disc is already inserted, go to step 3. (Depending on the disc, playback may start automatically.) • Hold disc by its edges only (p.
*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. ■ Forward/Reverse Scene Search Press FF/SLOW+ or REW/SLOW- during play. Press PLAY to release. • Starting forward/reverse search during play started from menu on Video CDs may recall menu. • Search speed, slow at first, increases with each additional press of the button up to 5 levels. ■ Forward/Reverse Chapter/Track Skip V.S.S.
Timer Recording Ready Checklist All connections are made. (pp. 12 ~ 15) TV and DECK are plugged in. Clock set correctly. (p. 18) Tape has record tab intact. (p. 6) Remote is in VCR mode. (Press VCR.) (➛ The VCR mode Light-up Indicator lights on DECK) Sufficient tape remaining for recording time. 1 2 POWER Press PROG* to display Program. SELECT 1) Press . 2) Set record DATE, press to select: 1~31= one time, or DAILY=Monday~Friday, or WEEKLY= same time each week.
*Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Review, Replace or Clear Program Contents: (Recording is not in progress) 1 2 To cancel a Timer Recording in progress... Press PROG to display Program List. Press to select number. Hold down STOP in VCR mode for a few seconds to cancel the Timer Recording. ( The TIMER Light-up Indicator goes out on DECK.) • Any future daily or weekly recording will be performed as programmed.
MTS Broadcast/ VHS Hi-Fi Stereo System Connection Make the Audio/Video Connection as shown on pp. 12 ~ 15. • You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV. Receivable Broadcast Types The following are possible audio broadcast types and onscreen displays. The signal being received is indicated with a “ ” mark while the selected audio mode is indicated with an arrow. To display the broadcast signal being received, ➛ press DISPLAY*.
*Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Audio Mode for Recording 1 Press AUDIO (SAP/Hi-Fi) to display audio mode. (Display disappears after 5 seconds.) 2 Press AUDIO (SAP/Hi-Fi) repeatedly to select desired mode. • Refer to “Receivable Broadcast Types” on p. 26. • Arrow indicates selection. Make a recording. See p. 21. VCR Operation 3 Audio Mode for Playback 1 2 3 Start playback. See p. 20.
Multi-Brand Control Feature Multi-Brand Control Setup The Remote Control can be set to control some Televisions. 1 2 Find your TV Brand Code Number on the following page. 3 Confirm code entry, Set up for TV control, ➛ hold down TV button, ➛ enter code with NUMBER keys. ➛ press POWER to turn selected unit on or off. • See table below for controllable functions in each mode. Notes • Repeat setup after remote battery replacement. • Remote will not control every TV made by the manufacturer listed.
TV Brand Code Numbers Panasonic ............................................... 01, 02 Quasar .................................................... 01, 02 RCA ................................................................ 03 GE .................................................................. 03 Zenith ............................................................. 04 Magnavox ...................................................... 05 Sylvania .........................................................
Tape Operation Search System Zero Search For each recording, an invisible index mark is placed on the tape. A program index and information are also included for timer recordings. These marks are used to access or scan recordings. Index Search 1 Press SEARCH* to display SEARCH in Stop or Play mode, and then press NUMBER keys to select recording number. • To calculate number, see below. Press FF/SLOW+ or REW/SLOW- on the remote to start search. 2 Play begins at search end.
*Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Repeat Play Set to playback a recording over and over. 1 2 Press ACTION to display MENU. Press to select “SET UP VCR,” and press SET. 3 • Playback repeats at tape end or if unrecorded portion over 30 sec. is detected. NUMBER keys SELECT ACTION 4 SET STOP • For repeat play in DVD mode, see page 47. FF/ SLOW+ PLAY Press ACTION to return to normal screen.
Tape Operation (continued) Tape Select Select your tape length so the tape position and amount of tape remaining are properly displayed. (See “Tape Position Display” section below.) 1 2 *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Press ACTION to display MENU. Press to select “SET UP VCR,” and press SET. 3 Press to select “TAPE SELECT,” and press SET to set “T-120,” “T-160” or “T-180.
Special VCR Features Weak Signal Display Feature When “ON,” picture is displayed regardless of signal strength. 1 2 Press ACTION to display MENU. Press to select “SET UP CHANNEL,” and press SET. 3 • ON: Picture is displayed regardless of signal condition, and may not always be clearly visible. OFF: Screen turns solid blue when signal is weak or non-existent. • Selecting ON has no effect on connected equipment with blue back feature.
Special VCR Features (continued) VCR/TV Selection Selector Feature Feature The VCR/TV selection can be set to auto or manual. 1 2 *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Press ACTION* to display MENU. Press to select “SET UP VCR,” and press SET. 3 Press to select “AUTO VCR/TV,” and press SET to set “ON” or “OFF.” VCR / TV • OFF(Manual): You select “VCR” or “TV” mode using the VCR/TV button on the remote.
Copying Your Tapes (Dubbing) Connection VCR/ Camcorder (Hi-Fi) OUT OUT VIDEO AUDIO TV DVD/VCR DECK IN 1 VIDEO IN 2 VIDEO L R Front of DECK IN FROM ANT. L AUDIO1 R VHF/ UHF VHF/UHF OUT TO TV L-AUDIO IN2-R (Audio/Video In Terminals on the front of DECK are available) Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on DECK. To monitor the dubbing, also connect TV as shown. 2 Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R” AUDIO IN terminals on DECK.
Disc Operation Subtitle Language (DVD only) You can select a different subtitle language (if offered) than the one set at the Settings for DVD Operation. (See p. 52.) 1 Press SUB TITLE* in Play mode to display the subtitle selection on-screen. Ready Checklist Please read “Basic DVD Operation” on page 22. [Subtitle language] [Audio sound track language] ENG FRA DEU ITA ESP NLD SVE NOR DAN POR RUS JPN CHI KOR MAL VIE THA • Display disappears after 5 seconds.
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again. When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc. Multiple Angle Viewing (DVD only) DVDs may contain scenes shot from multiple camera angles allowing the same scene to be viewed at different angles. You can view these angles, if available, using the ANGLE button.
Disc Operation (continued) Ready Checklist DECK is in DVD mode, press DVD. Video CD or CD is inserted. Program Play (Video CD/CD only) You can program specific tracks and order of play. 1 Press ACTION to display DVD MAIN MENU. 2 Press to select “PLAY MODE,” and press SET to display. 3 Press to select “PROGRAM PLAY,” and press SET to display. 4 CLEAR ACTION SELECT SET Press to select a track number (Track numbers on disc are displayed.), and press SET.
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Notes • Up to 16 tracks can be programmed. • “ ” or “ ” (depending on disc) indicates additional PROGRAM PLAY screen. Press for next or previous screen. • To clear the last program one by one Press to move to “CLEAR LAST” and press SET. (Pressing CLEAR on remote control also clears last program.) • To clear all programs Press to move to “CLEAR ALL” and press SET.
Disc Operation (continued) Random Play (Video CD/CD only) Tracks are played in a random order. 1 Ready Checklist DECK is in DVD mode, press DVD. Press ACTION* to display DVD MAIN MENU. 2 Press to select “PLAY MODE,” and press SET to display. 3 Press to select “RANDOM PLAY,” and press SET to begin random play. NUMBER keys CLEAR ACTION MENU • To cancel, press STOP during play, then press CLEAR.
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Title Menu (DVD only) Some DVDs have more than one title, e.g. movies. If the disc offers a title menu, you can select the desired title number. (Operation may vary according to the disc.) 1 TITLE MENU Cats Samurai Press TITLE* in Play mode to display the title screen.
DVD-RAM Operation (DVD-RAM only) You can enjoy playing your personally recorded/edited DVD-RAM discs on this DECK. Note • This DECK was designed for playback only. DVD-RAM recording is not possible. Play a DVD-RAM 1 Do steps 1 ~ 3 on page 22. 2 Press D.NAVI* or PLAY LIST to display Direct Navigator or Play List menu for easy title or scene selection. • Play begins from the first program title recorded on the DVD-RAM. • See below for “Direct Navigator” or next page for “Play List information”.
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Play List If the DVD-RAM features a Play List, your preselected list of favorite scenes is displayed for easy access. (Operation can vary according to how you edited the DVD-RAM.) 1 2 Press PLAY LIST in Play/Stop mode to display the Play List menu. Established time length Page No. Press to select a page and press to select a title (Play List No.).
DVD Operation using On-Screen Displays When DISPLAY is pressed, On-Screen Displays show disc information (title/chapter/track number, elapsed playing time) and DECK information (repeat play, play mode). 1 Ready Checklist DECK is in DVD mode, press DVD. Press DISPLAY* in Play or Stop mode to display “On-Screen Displays.” • Each press of DISPLAY changes the on-screen display as follows. (Refer to pp. 44 ~ 48.) Selected Disc information (See pp. 45, 46.) ➡ ➡ Selected DECK information (See pp. 47, 48.
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Detailed Descriptions of each On-Screen Display ■ Disc information screen (for DVD-Video) 1. TITLE No. Go directly to a preset title number. 1 2 3 4 5 • Select “TITLE”, and press SET. or NUMBER keys, and press SET. • Change the No. by pressing 2. CHAPTER No. Go directly to a preset chapter number. • Select “CHAPTER”, and press SET. • Change the No.
DVD Operation using On-Screen Displays (continued) ■ Disc information screen (for DVD-RAM) 1. Direct Navigation (PROGRAM) or PLAY LIST No. Go directly to a preset title number. 1 2 3 4 • Select “PROGRAM” or “PLAY LIST”, and press SET*. • Change the No. by pressing or NUMBER keys, and press SET. 2. Elapsed playing time The screen may be changed by selecting the elapsed time. • Select the elapsed playing time (“xx:xx:xx”), and press SET. • Change the elapsed time by pressing NUMBER keys .
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again. ■ DECK information screen (for DECK) a b c a. Repeat Play mode (see p. 48) Repeat play mode can be selected. • Select “REPEAT”, and press SET. • Change the desired mode during play by pressing , and press SET.
DVD Operation using On-Screen Displays (continued) For your reference Repeat Play mode example (see p.
MP3/JPEG Playback Operation This unit can play MP3/JPEG format CD-R or CD-RW recorded for personal use on a PC, etc. Some discs may not play due to the condition of the recording. 1 2 Press POWER* on the remote or DECK. Press OPEN/CLOSE, then place an MP3/JPEG disc into the disc tray. Press OPEN/CLOSE to close. MP3 Playback Do steps 1~3 at left. a b Press to select an MP3 file ( ). (During STOP mode) Press SET or PLAY to start playback.
MP3/JPEG Playback Operation (continued) JPEG Playback You can play back JPEG images. Displayable Image Size: 32x32~7680x7680 pixels Note • Some JPEG format may not be played back. Do steps 1~3 on page 49. 1 2 Press to select a JPEG file ( ). Press SET or PLAY. Selected JPEG file is displayed. [JPEG Playback Screen] ■ ■ ■ ■ ■ 3 Returned on the MP3/JPEG MENU ➡ Press STOP. (See p. 49) Next/Previous Search ➡ Press SKIP+ | or SKIP- | . Start Slide-show ➡ Press FF/SLOW+ or REW/SLOW-.
JPEG Zoom (During JPEG Playback.) You can enlarge specific portions of a JPEG picture and select the zoom ratio using the ZOOM button on the remote during JPEG Playback screen. Set Zoom size. Press ZOOM repeatedly to change display as follows. ➡ Press STOP to return the MP3/JPEG MENU. SELECT ACTION SET STOP FF/ SLOW+ PLAY • You can enlarge the center portion of the image to one of 2 magnifications. • Operation can be done during Rotation (below). X 1.
Settings for DVD Operation 1 2 Press ACTION* to display DVD MAIN MENU. Press to select an item, and press SET. Once initial settings are done, they remain in memory (even after power is turned off) until changed. This means DECK will operate under the same conditions (especially DVDs) each time. Ready Checklist DECK is in DVD mode, press DVD. DISC LANGUAGES (See below) All languages offered on the disc can be set. If a language not offered is set, the original disc language will be selected.
*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Audio Output (DVD only) Select the digital output to be output from the optical digital audio output connector of DECK. 1 2 Press ACTION to display DVD MAIN MENU. Press to select “AUDIO OUTPUT,” and press SET to display screen. 3 Press to select an item, and press SET repeatedly for output. (See below.) Ready Checklist DECK is in DVD mode, press DVD.
Settings for DVD Operation (continued) Still Mode (DVD only) Set to reduce jitter in a displayed still picture or a motion picture. 1 2 Press ACTION* to display DVD MAIN MENU. Press to select “STILL MODE,” and press SET repeatedly for mode. (See below.) ACTION SELECT AUTO: “FIELD” (Field still) or “FRAME” (Frame still) is automatically selected during the still mode. (Factory preset) FIELD: “FIELD” (Field still) is always selected. This setting will reduce jitter when compared with “AUTO” on some discs.
*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. PROGRESSIVE OUT Notes Sets the Component Video Output Connector (p. 10, 13) to output the Progressive scan signal. 1 2 Press ACTION to display DVD MAIN MENU. Press to select “PROGRESSIVE OUT,” and press SET repeatedly for mode. (See below.) OFF: ON: 3 Progressive scan signal is not output. Progressive scan signal is output from the Component Video Output Connector.
Language Code List Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/or “MENUS” (see p. 52).
Warning and Instruction Displays These displays will alert you to a missed operation or provide further instructions. OSD Caution Page PLEASE SET CLOCK BY PRESSING ACTION KEY If you attempt to set or review a Timer Recording and the Clock is not set... 24 PLEASE PREPARE FOR TIMER REC If the DECK is not in Stop mode, or cassette is not inserted, or cassette has no record tab, or tape is at its end 2 minutes before a Timer Recording is about to begin...
Before Requesting Service Check the following points if you are having trouble with your DECK. Power Solution No power… • Completely insert Power Plug into an AC outlet. • Press POWER button on. • Make sure power source is active. Power turns itself off... • Auto power-off (shutoff) occurs after about 5 min. in DVD mode with no operation, or if there is no broadcast signal in TV or Playback mode. Turn the power back on. (pp. 23, 33) Solution Recording & Playback 58 TV program cannot be recorded...
DVD/ Video CD/ CD Solution Play fails to start even when PLAY is pressed... • This DECK cannot play discs other than DVDs, Video CDs and CDs. • The disc may be dirty and require cleaning. Picture is distorted during rapid advance or rapid reverse... • The picture will be somewhat distorted at times: this is normal. No Forward/Reverse Scene Search play... • Some discs may have sections which prohibit Forward/Reverse Scene Search. (p.
Limited Warranty PANASONIC CONSUMER ELECTRONICS COMPANY, DIVISION OF PANASONIC CORPORATION OF NORTH AMERICA One Panasonic Way Secaucus, New Jersey 07094 PANASONIC SALES COMPANY, DIVISION OF PANASONIC PUERTO RICO, INC., AVE. 65 de Infantería, Km. 9.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY COVERAGE”. THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, cost of having someone remove or re-install an installed unit if applicable, travel to and from the servicer, loss of or damage to media or images, data or other recorded content.
Medidas de seguridad y precauciones importantes PARA REDUCIR EL RIESGO DE GOLPES ELÉCTRICOS, INCENDIOS, HERIDAS O DAÑOS A ESTE PRODUCTO, LEA Y GUARDE TODAS LAS INSTRUCCIONES DE SEGURIDAD Y FUNCIONAMIENTO. TENGA EN CUENTA TODAS LAS ADVERTENCIAS INDICADAS EN EL MANUAL Y EN EL PRODUCTO. INSTALACIÓN PRECAUCIÓN CON LA FUENTE DE ALIMENTACIÓN El equipo solo debe hacerse funcionar desde una fuente de a limentación que se indique en la unidad o en este manual.
PRECAUCIONES DE SEGURIDAD PARA PREVENIR INCENDIOS O CHOQUES ELÉCTRICOS NO EXPONGA ESTE APARATO A LA LLUVIA O LA HUMEDAD. PARA PREVENIR CHOQUES ELÉCTRICOS, ASEGURASE QUE LA CLAVIJA HAGA JUEGO CON EL ENCHUFE Y CONÉCTELO COMPLETAMENTE. Este símbolo advierte al usuario de que hay voltaje sin aislamiento dentro de la unidad de suficiente magnitud como para ocasionar sacudidas eléctricas. Por lo tanto, resultará peligroso realizar cualquier tipo de contacto con toda pieza interna de la unidad.
Spanish Quick Use Guide/ Guía para rápida consulta CONEXIONES/CONFIGURACION (READY TO PLAY) Para ajustar el idioma, canalINICIAL y Realice la conexión de la antena o TV por cable antes de enchufar el cable de CA. El DVD/VCR iniciará automáticamente la fijación de los canales y del reloj al enchufar el cable de CA. CONEXIONES DVD/VCR Para Ant/Cable ➛ DVD/VCR ➛ TV 1 2 Terminal IN FROM ANT. Televisor 1 Conecte el cable de la antena al terminal IN FROM ANT del DVD/VCR.
Programación fácil para la grabación con temporizador Operaciones básicas para la reproducción 1 Inserte un cassette, • La alimentación del DECK se activa. Si Auto VCR/TV (consulte la página 34) está en “INACT (OFF)”, presione VCR/TV en el control remoto para el modo VCR. PLAY para reproducir el cassette. 2 Presione • Si el cassette no tiene la lengüeta de PROG 1 Presione para visualizar la pantalla de Programacion. 2 prevención de grabación (página 6), se inicia la reproducción automáticamente.
Spanish Quick Use Guide/ Guía para rápida consulta Operaciones básicas del DVD 1 Presione DVD para seleccionar el modo DVD. OPEN/CLOSE. 2 1)2) Presione Ponga un disco en la bandeja de disco. • Sujete el disco sin tocar ninguna de sus superficies, póngalo con el lado donde esté impreso el título hacia arriba, alinéelo con las guías y póngalo en su posición apropiada. Disco de 3” (8 cm) / Disco de 5” (12 cm) 3 Presione PLAY para iniciar la reproducción. La bandeja del disco se cierra automáticamente.
Fijaciones iniciales Selección de IDIOMAS DEL DISCO [DVD solamente] 1 Presione DVD para seleccionar el modo DVD. Seleccione “AUDIO” ACTION en el modo de parada (Fijación de fábrica : inglés) 2 Presione para visualizar MENU. Inglés / Español / Francés / Japonés : Original : Se seleccionará el idioma original Presione para seleccionar el artículo 3 deseado. de cada disco. OTRO 0000 : Se puede seleccionar el otro Presione SET. IDIOMAS DEL DISCO Todos los idiomas ofrecidos en el disco pueden ser ajustados.
Spanish Quick Use Guide/ Guía para rápida consulta Cambio del idioma de la pista de sonido [DVD solamente] Selección de vocal para los discos de Karaoke [DVD/CD-Vídeo solamente] Presione AUDIO durante la reproducción 1 para visualizar la pantalla AUDIO. 2 Presione para seleccionar VOZ y presione AUDIO o para seleccionar tal como se indica a continuación.
Funcionamiento de la ejecución de MP3/JPEG Puede utilizar esta unidad para reproducir audio de formato MP3/JPEG, grabado para uso personal con una computadora, etc., en un CD-ROM o CD-RW. La ejecución no podrá realizarse en algunos casos, debido a las condiciones de la grabación. POWER en el control remoto 1 oPresione DECK. OPEN/CLOSE y a continuacion 2 Presione coloque un disco MP3/JPEG en la bandeja de discos. Presione OPEN/CLOSE para cerrarla.
Index DECK & VCR A ACTION button ................................ 8, 18 Accessories ........................................... 4 ADD/DELETE button (Add or Delete a Channel) ............ 8, 19 Audio Broadcast types (Stereo/SAP/Mono) ........................... 26 Audio Mode (Playback, Recording) ... 27 Auto Operation Functions ................... 31 Auto Shut-Off ....................................... 33 B Batteries ................................................ 4 C Channel (“SET UP CHANNEL”) .........
DVD A ACTION button ................................ 8, 52 ANGLE button (Multiple Angle Viewing) ......... 8, 37, 51 AUDIO button (Audio Soundtrack Language) ..... 8, 36 Audio Output (For Selecting Audio Output) ............ 53 Auto-Power Off Function ..................... 23 A/V OPTIMIZER ................................... 55 C CLEAR button ........................... 8, 38, 40 Component Video Output ............. 10, 13 D Direct Navigator .................................. 42 Disc Languages .............
LSQT0908 A Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America One Panasonic Way Secaucus, New Jersey 07094 Panasonic Sales Company (“PSC”), Division of Panasonic Puerto Rico, Inc. Ave. 65 de Infantería. Km. 9.5 San Gabriel Industrial Park, Carolina, Puerto Rico 00985 PV-D4745S P36-72 (041224).