Operating Instructions Model No. PV-D4753S-K Initial Setup (Connection) DVD/VCR DECK Basic Operation VCR Operation MULTI FORMAT PLAYBACK As an ENERGY STAR ® Participant, Panasonic has determined that this product or product model meets the ENERGY STAR ® guidelines for energy efficiency. Please read these instructions carefully before attempting to connect, operate or adjust this product. Please save this manual. For assistance, please call : 1-800-561-5505 or visit us at www.panasonic.
Important Safeguards and Precautions FOR YOUR SAFETY, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE UNIT INSTALLATION OUTDOOR ANTENNA INSTALLATION 1 SAFE ANTENNA AND CABLE CONNECTION If an outside antenna or cable system is connected to the equipment, be sure the antenna or cable system is grounded so as to provide some protection against built up static charges and voltage surges.
Safety Precautions WARNING: To prevent fire or shock hazard, do not expose this equipment to rain or moisture. CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert. This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.
Before Using Congratulations on your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your DECK. • Date of Purchase • Dealer Purchased From • Dealer Address • Dealer Phone No. PV-D4753S-K • Model No. • Serial No.
Table of Contents DVD / VCR Important Safeguards and Precautions ............................ 2, 3 Before Using ............................................................................ 4 DECK / Disc / Cassette Information .................................. 6 , 7 Location of Controls ....................................................... 8 ~ 10 Displays (On Screen Displays and Multi Function Display) .................... 11 Connections ..................................................................
DECK / Disc / Cassette Information Prevent Accidental Tape Erasure DVD-RAM discs DVD-RAM discs must meet the following conditions for this unit to be able to play them. Break off the tab to prevent recording. Record Tab Type Screw driver Capacity To record again Cover the hole with cellophane tape. • Non-cartridge discs • Discs that can be removed from their cartridges (TYPE 2 and 4) • 12 cm (5”) 9.4 GB (double-sided) and 4.7 GB (single-sided) • 8 cm (3”) 2.
Specifications Input/Output Terminal: Input Terminal: Output Terminal: Operating Temperature: Operating Humidity: Weight: Dimensions: Discs Played (1) DVD-Video Disc DVD-Audio Disc DVD-RAM Disc (2) Compact Disc (CD-DA, Video CD) (CD-R/CD-RW, MP3, WMA, JPEG) Digital Audio Output: Pickup: 120 V AC, 60 Hz Power On: Approx. 32 watts, Power Off: Approx.
Location of Controls Bold: VCR Function Italic: DVD Function Bold Italic: VCR and DVD Functions Normal: Others DISPLAY Remote Control EJECT / OPEN / CLOSE pp. 11, 44 pp. 20, 22 TV mode POWER p. 28 VCR mode DVD mode p. 28 p. 28 DSS / CABLE mode INPUT p. 35 p. 28 PLAY FAST FORWARD / SEARCH / SLOW+ pp. 20, 22 pp. 20, 23 REWIND / SEARCH / SLOW- PAUSE / STILL pp. 20, 23 pp. 20, 23 STOP VCR/TV pp. 20, 22 p. 21 ADD/DELETE / CLEAR NUMBER keys pp.
Bold: VCR Function Italic: DVD Function Bold Italic: VCR and DVD Functions Normal: Others STOP/EJECT If the disc cannot be removed... First, unplug DECK. Then, prepare a rigid wire (e.g. an extended paper clip) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc. p. 20 FAST FORWARD/SEARCH p. 20 PLAY Initial Setup (Connection) FrontView View DECK Front ofof DECK Over 2 inches p.
Location of Controls (continued) Bold: VCR Function Italic: DVD Function Bold Italic: VCR and DVD Functions AC Power Plug VHF/UHF Antenna Output Terminal • While plugged into an AC outlet, p. 12 Rear View of DECK this DECK consumes 4 W of electrical power in off mode. VHF/UHF Antenna Input Terminal p. 12 Component Video Output Connector (Y, PB, PR) (DVD Only) p. 13 Video Output Connector p. 12 Video Input Connector p. 35 5.
Displays (On Screen & Multi Function) Function & Channel Displays CH 0 8 When a function button is pressed, e.g. PLAY, or you change channels, a 5-second display appears. ➛ press DISPLAY. Blank Tape/ No Video Signal Indications Whenever a blank section of a tape comes up in Play mode, or when the selected channel has no broadcast signal with Weak Signal Display Feature (p. 33) set to OFF, the TV screen will turn solid blue.
Connections Basic Connections • If your TV has AUDIO and VIDEO IN terminals, connect them to DECK for higher quality picture and sound. • You can enjoy stereo sound even if your TV is not stereo by connecting a stereo amplifier to DECK. • Connect DECK and TV with an RF Coaxial Cable a (supplied) or an AV Cable b (not supplied) as shown in the figure below.
Other Connections You Can IN 1 OUT IN FROM ANT. IN Cable Box VHF/UHF OUT TO TV IN OUT VHF/ UHF R L ANT or CATV OUT Cable Box IN IN 1 IN FROM ANT. OUT VHF/UHF OUT TO TV 2-Way Splitter Cable Box OUT 1 OUT 2 IN OUT A/B Switch IN 1 IN 2 • record scrambled channels. OUT AUDIO VIDEO ■ Connect With Two Cable Boxes DVD/VCR DECK • view any (including scrambled) channel.
Connections (continued) Audio Connections Ready Checklist Turn down the volume, then turn DECK, as well as other equipment to be connected, off before proceeding with connection. Do not block ventilation holes of any of the equipment and arrange them so that air can circulate freely. Read through the instructions before connecting other equipment. Ensure that you observe the colour coding when connecting audio and video cables.
■ Connecting Amplifier (5.1 ch Surround system) A. Digital connection (DECK OPTICAL Digital Audio Output Connector) When DVDs recorded in Dolby Digital or DTS are played, Dolby Digital bitstream or DTS bitstream is output from the DECK OPTICAL Digital Audio Output Connector. When DECK is connected to a Dolby Digital or DTS receiver, you can enjoy theater-quality audio in your home. [An optical digital audio cable (optional) is required when an optional Dolby Digital or DTS receiver is used.] B.
Initial Setup for Basic Connections (Ready to Play) Before doing Initial Setup 1 Turn TV on. 2 See connections a RF Coaxial Cable Connection and b AV Cable Connection on page 12. Set TV to channel 3. Set TV to VIDEO. 3 [DECK ➛ TV] • Go to “Initial Setup (Ready to Play).” (See below.) [Cable Box ➛ DECK ➛ TV], [DSS ➛ DECK ➛ TV] • Turn on Cable Box and set it to your Public Broadcasting Station (PBS) channel in your time zone.
dy to Play) *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Settings are made automatically. When setup is done, this screen appears. 6 / 8/ 2003 SUN 2 : 20PM EJECT DST : ON SETT I NG : CH 10 AUTO CLOCK SET VCR COMPLETED If “AUTO CLOCK SET IS INCOMPLETE” appears, manually set clock. See below.
Reset Language, Channels, Clock, 1 Press ACTION* to display MENU. MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 VCR’s • PROGRAM functions are not available when using COMPONENT Video Output and S-VIDEO OUT. Please set TV to either RF INPUT or VIDEO INPUT, and then press PROGRAM. SELECT : SET:SET EXIT : ACTION 2 Language Channels 1) Press to select language item. 1) Press to select “SET UP CHANNEL,” and press SET.
k, VCR’s Output Channel *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Time Zone Adjust SELECT : SET : SET EXIT : ACTION 2) Press to select “TIME ZONE ADJUST,” 1) Press to select “VCR’S OUTPUT CH.,” and press SET. ACTION ADD/DLT SELECT MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 SET SELECT : SET : SET EXIT : ACTION CH / 2) Press SET.
Playback/ Record on a Tape Ready Checklist All connections are made. (pp. 12 ~ 15) TV and DECK are plugged in. TV is on and tuned to CH 3, 4, or VIDEO. Remote is in VCR mode. (Press VCR.) Playback a Tape 1 Insert a tape. 2 Press PLAY* to play a tape. EJECT DVD VCR PLAY REW/SLOWVCR/TV STOP FF/SLOW+ PAUSE/ STILL • DECK power comes on. If Auto VCR/TV (see p. 32) is set to “OFF,” press VCR/TV on the remote to be VCR mode. • If tape has no rec. tab (p. 6), auto play begins.
*Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Record on a Tape This video recorder, equipped with HQ (High Quality) system, is compatible with existing VHS equipment. Only use mark. Only tapes tapes with the tested and inspected for use in 2, 4, 6, and 8 hour machines are recommended. Insert a tape with a record tab (p. 6). 1 • DECK power comes on. If Auto VCR/TV (see p.
Basic DVD Operation Ready Checklist All connections are made. (pp. 12 ~ 15) DECK is plugged in. If DECK is connected to an audio amplifier, turn the stereo system’s power on. OPEN/ CLOSE POWER 1 2 3 REW/ SLOW- FF/ SLOW+ STOP PAUSE/ STILL NUMBER keys • If a disc is already inserted, go to step 4. (Depending on the disc, playback may start automatically.) Press OPEN/CLOSE, and then place a disc into the disc tray. 1 2 4 RETURN SKIP SELECT • Hold disc by its edges only (p.
*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. ■ Forward/Reverse Scene Search Press FF/SLOW+ or REW/SLOWduring play. Press PLAY to release. • Starting forward/reverse search during play started from menu on Video CDs may recall menu. • Search speed, slow at first, increases with each additional press of the button up to 5 levels. ■ Forward/Reverse Chapter/Track Skip Press SKIP | or | SKIP during play.
Timer Recording Ready Checklist All connections are made. (pp. 12 ~ 15) TV and DECK are plugged in. Clock set correctly. (p. 18) Tape has rec.tab. (p. 6) Remote is in VCR mode. (Press VCR.) Sufficient tape remaining for recording time. 1 Press PROG* to display Program.
*Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Review, Replace or Clear Program Contents: (Recording is not in progress) 1 2 Press PROG to display Program List. DT START STOP 7 9 : 00A 12 : 00A 8 10 : 00P 12 : 00P 10 8 : 00P 9 : 00P 9 : 00P 10 : 00P SU CANCEL SELECT ENTER EXIT 3 CH SPD 08 SP 02 SP 10 SP L1 LP : ADD / DLT 1-8 : : SET : PROG Press to select number and press SET to display.
MTS Broadcast/ VHS Hi-Fi Stereo System Connection Make the Audio/Video Connection as shown on pp. 12 ~ 15. • You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV. Receivable Broadcast Types The following are possible audio broadcast types and onscreen displays. The signal being received is indicated with an “ ” mark while the selected audio mode is indicated with an arrow. DISPLAY To display the broadcast signal being received, ➛ press DISPLAY*.
*Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Audio Mode for Recording 1 Press AUDIO (SAP/Hi-Fi) to display audio mode. (Display disappears after 5 seconds.) 2 STEREO SAP MONO Press AUDIO (SAP/Hi-Fi) repeatedly to select desired mode. • Refer to “Receivable Broadcast Types” on page 26. • Arrow indicates selection. 3 Make a recording. See page 21. VCR Operation Audio Mode for Playback 1 2 3 Start playback.
Multi-Brand Control Feature POWER Multi-Brand Control Setup VCR The Remote Control can be set to control some TV and Cable Box/DSS functions. 1 2 DSS/ CABLE Find your TV and Cable Box/DSS Receiver Brand Code Number on the following page. TV DVD Set up for TV control, ➛ hold down TV button, ➛ enter code with NUMBER keys. Set up for Cable or DSS control, ➛ hold down DSS/CABLE button, ➛ enter code with NUMBER keys. • If code number is 100 or greater, ➛ e.g., press 1 - 0 - 2 for 102.
TV Brand Code Numbers Panasonic ....................... 01, Quasar ............................ 01, RCA ....................................... GE ......................................... Zenith .................................... Magnavox .............................. 02 02 03 03 04 05 Sylvania ................................ Sharp ............................... 06, Sony ...................................... Toshiba ................................. Sanyo ....................................
Tape Operation Search System For each recording, an invisible index mark is placed on the tape. A program index and information are also included for timer recordings. These marks are used to access or scan recordings. Program End Search Index Search 1 Press SEARCH* to display SEARCH in Stop or Play mode, and then press NUMBER keys to select recording number.
*Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Auto Operation Functions Auto Play Insert a tape ➛ Power comes on, ➛ Play starts if there is no record tab (see p. 6).
Tape Operation (continued) Repeat Play VCR/TV Selector Feature Set to playback a recording over and over. 1 2 Press ACTION* to display MENU. MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 Press to select “SET UP VCR,” and press SET. SELECT : SET : SET EXIT : ACTION 3 SET UP VCR REPEAT PLAY REMOTE WARN I NG AUTO SHUT-OFF AUTO VCR/TV SELECT : END : ACT I ON : : : : OFF ON OFF OFF Press to select “REPEAT PLAY,” and press SET to set “ON” or “OFF.
Special VCR Features *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Weak Signal Display Feature DISPLAY When “ON,” picture is displayed regardless of signal strength. 1 2 STOP MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 SELECT : SET : SET EXIT : ACTION ACTION SELECT Press ACTION to display MENU.
Special VCR Features (continued) Remote Warning Feature If Multi-brand feature is used (p. 28), and this feature is set to on, a warning appears whenever an invalid key is pressed in TV, DSS or CABLE mode. 1 2 Press ACTION* to display MENU. MENU SET UP VCR SET CLOCK SET UP CHANNEL IDIOMA/LANGUE : ENGLISH VCR’S OUTPUT CH:3 SELECT : SET : SET EXIT : ACTION 3 *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again.
Copying Your Tapes (Dubbing) Connection VCR/ Camcorder (Hi-Fi) OUT OUT VIDEO AUDIO TV DVD/VCR DECK IN 1 VIDEO IN 2 VIDEO L R Front of DECK IN FROM ANT. L AUDIO1 R VHF/ UHF VHF/UHF OUT TO TV L-AUDIO IN2-R (Audio/Video In Terminals on the front of DECK are available) 1 Connect VIDEO OUT terminal on Playing VCR to VIDEO IN terminal on DECK. To monitor the dubbing, also connect TV as shown. 2 Connect “L” and “R” AUDIO OUT terminals on Playing VCR to “L” and “R” AUDIO IN terminals on DECK.
Disc Operation Subtitle Language (DVD only) You can select a different subtitle language (if offered) than the one set at the Settings for DVD Operation. (See p. 53.) 1 Press SUB TITLE* in Play mode to display the subtitle selection on-screen. • Display disappears after 5 seconds. • When no subtitles are offered, “-” will be displayed instead of the language number. 2 Te amo Press to select a language. Press to select “ON” or “OFF.” Ready Checklist Please read “Basic DVD Operation” on page 22.
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again. When appears on the screen while a button is being operated, it means that the corresponding operation is prohibited by DECK or the disc. Multiple Angle Viewing (DVD only) DVDs may contain scenes shot from multiple camera angles allowing the same scene to be viewed at different angles. You can view these angles, if available, using the ANGLE button.
Disc Operation (continued) Title Menu (DVD only) Some DVDs have more than one title, e.g. movies. If the disc offers a title menu, you can select the desired title number. (Operation may vary according to the disc.) 1 T I TLE MENU Dogs Cas t l es Love r s B i r ds Press TITLE* in Play mode to display the title screen. 2 T I TLE MENU Dogs Cas t l es Love r s B i r ds B i rds of the world Press or NUMBER keys to select a title, and press SET or PLAY to start playing.
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Program Play (Video CD/CD only) Ready Checklist DECK is in DVD mode, press DVD. Video CD or CD is inserted. You can program specific tracks and order of play. 1 2 Press ACTION to display DVD MAIN MENU.
Disc Operation (continued) Random Play (Video CD/CD only) Tracks are played in a random order. 1 2 Press ACTION* to display DVD MAIN MENU. DVD MAIN MENU DISC LANGUAGES AUDIO OUTPUT ST I L L MODE : AUTO TV MODE : 4:3 Letterbox PARENTAL LOCK :LEVEL 8 PLAY MODE SELECT SET END 3 Ready Checklist DECK is in DVD mode, press DVD. : : SET : ACTION PLAY MODE PROGRAM PLAY RANDOM PLAY SELECT SET END : : SET : ACTION Press to select “PLAY MODE,” and press SET to display.
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again. DVD-Audio Operation This DECK, equipped with a 192 kHz/ 24 bit Audio D/A converter, supports DVD-Audio recorded with high quality sound. The DVD-Audio feature includes “Still Image Skip” and “Bonus Group Playback” functions. (See below.) Please refer to “Basic DVD Operation” on pages 22 and 23. Still Image Skip DVD-Audio still images (only if contained) can be skipped over.
DVD-RAM Operation (DVD-RAM only) You can enjoy playing your personally recorded/edited DVD-RAM discs on this DECK. Note • This DECK was designed for playback only. DVD-RAM recording is not possible. Play a DVD-RAM 1 Do steps 1 ~ 3 on page 22. 2 Press TITLE* or MENU to display Direct Navigator or Play List menu for easy title or scene selection. • Play begins from the first program title recorded on the DVD-RAM. • See below for Direct Navigator or next page for Play List information.
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Play List If the DVD-RAM features a Play List, your preselected list of favorite scenes is displayed for easy access. (Operation can vary according to how you edited the DVD-RAM.) 1 2 Press MENU in Play/Stop mode to display the Play List menu. Press to select a page and press to select a title (Play List No.). Then, press SET or PLAY to start playing.
DVD Operation using On-Screen Displays When DISPLAY is pressed, On-Screen Displays show disc information (title/chapter/track number, elapsed playing time) and DECK information (repeat play, play mode). 1 Ready Checklist DECK is in DVD mode, press DVD. Press DISPLAY* in Play or Stop mode to display “On-Screen Displays.” • Each press of DISPLAY changes the on-screen display as follows. (Refer to pp. 44 ~ 48.
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Detailed Descriptions of each On-Screen Display ■ Disc information screen (for DVD-Video) 1. TITLE No. 1 2 • Select “TITLE”, and press SET. or NUMBER keys, and press SET. • Change the No. by pressing T I TLE : 1 CHAPTER : 12 DVD 01 : 12 : 55 3 4 2. CHAPTER No. • Select “CHAPTER”, and press SET. • Change the No. by pressing or NUMBER keys, and press SET.
DVD Operation using On-Screen Displays (continued) ■ Disc information screen (for Video CD/ CD) 1. TRACK No. 1 2 TRACK PBC : 1 : OFF VIDEO CD 01 : 35 : 12 3 4 • Select “TRACK”, and press SET* . • Change the No. by pressing or NUMBER keys, and press SET. 2. Playback control ON/OFF [Video CD with playback control only] ON Video CD menu play is displayed. OFF Video CD menu play is not displayed. SET : SET NEXT : DISPLAY 3. Disc currently being played Video CD CD 4.
*Important: if a remote control button does not work when pressed, press the DVD button on the remote and try the button again. ■ DECK information screen (for DECK) 1. Repeat Play • Select “REPEAT”, and press SET. • Change the desired mode during play by pressing DVD-Video CHAPTER DVD-Audio TRACK DVD-RAM (PROGRAM) PROGRAM (PLAY LIST) PLAY LIST Video CD/CD TRACK , and press SET. TITLE GROUP DISC ALL PLAY LIST DISC OFF OFF OFF OFF OFF 1 PLAY REPEAT : OFF SELECT : SET : SET END : DISPLAY 2.
DVD Operation using On-Screen Displays (continued) For your reference • CHAPTER/TITLE REPEAT PLAY (DVD-Video) OPEN/ CLOSE CURRENT PLAYBACK POSITION TITLE chapter chapter chapter CHAPTER REPEAT TITLE REPEAT NORMAL PLAY POWER PLAY FF/REW PAUSE STOP • TRACK/GROUP REPEAT PLAY (DVD-Audio) CURRENT PLAYBACK POSITION GROUP track GROUP track track track track track NUMBER keys SKIP TRACK REPEAT GROUP REPEAT NORMAL PLAY SKIP SELECT • TRACK/DISC REPEAT PLAY (Video CD/CD) CURRENT PLAYBACK POSITION t
MP3/WMA/JPEG Playback Operation This unit can play MP3/WMA/JPEG format CD-R or CD-RW recorded for personal use on a PC, etc. Some discs may not play due to the condition of the recording. 1 2 Press POWER* on the remote or DECK. Press OPEN/CLOSE, then place an MP3/WMA/JPEG disc into the disc tray. Press OPEN/CLOSE to close. 3 • MP3/WMA/JPEG menu is displayed. • Playback starts automatically (except JPEG files). • CD directory is displayed.
MP3/WMA/JPEG Playback Operation (continued) JPEG Playback You can play back JPEG images. Displayable Image Size: 32x32~7680x7680 pixels Note • Some JPEG format may not be played back. Do steps 1~3 on page 49. 1 2 Press to select an JPEG file ( ). Press SET or PLAY. Selected JPEG file is displayed. [JPEG Playback Screen] ■ Returned on the MP3/WMA/JPEG MENU ➡ Press STOP. (See p. 49) ■ Next/Previous Search ➡ Press SKIP | or | SKIP. ■ Start Slide-show ➡ Press FF/SLOW+ or REW/SLOW-.
JPEG Zoom (During JPEG Playback.) You can enlarge specific portions of a JPEG picture and select the zoom ratio using the ZOOM button on the remote during JPEG Playback screen. Set Zoom size. Press ZOOM repeatedly to change display as follows. ➡ Press STOP to return the MP3/WMA/JPEG MENU. PLAY REW/ SLOW- FF/ SLOW+ • You can enlarge the center portion of the image to one of 2 magnifications. • Operation can be done during Rotation (below). X 1.0 (ORIGINAL) STOP STILL X 1.5 (ZOOM 1) 1st press X 2.
DVD Lock Feature *Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. You can prevent playback of DVDs of a specific rating level which may be unsuitable for children. • Some DVDs are encoded with a rating level. If the disc rating is higher (stricter) than the one you preset, playback will be prohibited. Ready Checklist DECK is in DVD mode, press DVD.
Settings for DVD Operation 1 2 Press ACTION to display DVD MAIN MENU. DVD MAIN MENU DISC LANGUAGES AUDIO OUTPUT ST I L L MODE : AUTO TV MODE : 4:3 Letterbox PARENTAL LOCK :LEVEL 8 Press to select an item, and press SET. Once initial settings are done, they remain in memory (even after power off) until changed. This means DECK will operate under the same conditions (especially DVDs) each time. Ready Checklist DECK is in DVD mode, press DVD.
Settings for DVD Operation (continued) Audio Output Ready Checklist Select the digital output to be output from the optical digital audio output connector of DECK. 1 2 Press ACTION* to display DVD MAIN MENU.
*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Speaker Output Setup Set the number of speakers connected to the receiver (amplifier, decoder.) (See pp.14, 15.) 1 Do steps 1~3 on page 54.
Settings for DVD Operation (continued) Output Balance Setup Adjust the volume level output from the speakers. To adjust, play a disc or set the “TEST SIGNAL” (p.57) to ON. Then adjust while confirming the volume. (Even if “OFF” or "NONE" is set in “SPEAKER SIZE,” the speaker OUTPUT BALANCE can still be set.) 1 Do steps 1~2 of “Speaker Output Setup” on page 55. 2 Press to select “OUTPUT BALANCE,” and press SET to display OUTPUT BALANCE screen. Press to select an item, and press SET repeatedly.
*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Test Signal Setup Still Mode This feature assists in the setting of OUTPUT BALANCE. Starting with (L) front speaker, a test sound is output in clockwise order. While the test signal is output, adjust the output of the center speaker and Surround speaker (R/L). (See “OUTPUT BALANCE.” P. 56.) steps 1~2 of “Output 1 Do Balance Setup” on page 56.
Language Code List Enter the appropriate code number for the initial settings “AUDIO”, “SUBTITLE” and/or “MENUS” (see p. 53).
Warning and Instruction Displays These displays will alert you to a missed operation or provide further instructions.
Before Requesting Service Check the following points if you are having trouble with your DECK. Power Correction No power… • Completely insert Power Plug into an AC outlet. • Set POWER button to on. • Make sure power source is active. Power turns itself off... • Auto power-off (shutoff) occurs after about 5 min. in DVD mode with no operation, or if there is no broadcast signal in TV or Playback mode. Turn the power back on. (pp. 23, 33) Correction Recording & Playback TV program cannot be recorded...
Check the following points if you are having trouble with your DECK. DVD/ Video CD/ CD Correction Play fails to start even when PLAY is pressed... • This DECK cannot play discs other than DVDs, Video CDs and CDs. • The disc may be dirty and require cleaning. Play starts but then stops immediately... • Be sure disc is installed with label side up. Picture is distorted during rapid advance or rapid reverse... • The picture will be somewhat distorted at times: this is normal.
Limited Warranty Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 PANASONIC PRODUCT – LIMITED WARRANTY Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship and agrees to remedy any such defect for a period as stated below from the date of original purchase.
Servicentre List WARRANTY SERVICE For product operation and information assistance, please contact your Dealer or our Customer Care Centre at: Telephone #: Fax #: Web: (905) 624-5505 (905) 238-2360 www.panasonic.ca For product repairs, please contact one of the following: • Your Dealer who will inform you of an authorized Servicentre nearest you. • Our Customer Care Centre at (905) 624-5505 or www.panasonic.
Index DECK & VCR A ACTION button ........................................................ 8, 18 Accessories ................................................................... 4 ADD/DELETE button (Add or Delete a Channel) ... 8, 19 Audio Broadcast types (Stereo/SAP/Mono) .............. 26 Audio Mode (Playback, Recording) ............................ 27 Auto Operation Functions ........................................... 31 Auto Shut-Off ..............................................................
Manuel d’utilisation Modèle PV-D4753S-K Réglage initial (Raccordements) Combiné magnétoscope-lecteur DVD Fonctions de base Fonctions du magnétoscope Fonctions du DVD Se reporter aux pages 12 à 17 pour les raccordements et le paramétrage initial. Lecture multiformat Lecture À titre de participant au programme ENERGY STAR,® Panasonic assure que cet appareil, ou ce modèle, satisfait aux normes d’efficacité énergétique du programme.
Importantes mesures de sécurité Pour votre sécurité, lire et observer les mesures de sécurité et le manuel d’utilisation. Tenir compte également de toutes les mises en garde indiquées dans le manuel et inscrites sur l’appareil. Installation 1 Mise en garde – Alimentation N’alimenter l’appareil que sur le type de courant indiqué dans ce manuel ou sur l’appareil. Dans le doute, consulter un détaillant ou la compagnie d’électricité.
Mesures de sécurité Avertissement: Afin de prévenir tout risque d’incendie ou de chocs Attention: électriques, ne pas exposer cet appareil à la pluie ou à une humidité excessive. Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond. Le symbole de l’éclair dans un triangle équilatéral indique la présence d’une tension suffisamment élevée pour engendrer un risque de chocs électriques.
Avant l’utilisation Félicitations Vous avez arrêté votre choix sur l’un des produits les plus perfectionnés et les plus fiables sur le marché. Utilisé correctement, il ne manquera pas de procurer, à vous et à votre famille, des années de plaisir. Veuillez prendre le temps d’inscrire les informations demandées ci-dessous. Le numéro de série est inscrit sur l’étiquette apposée sur le panneau arrière du combiné.
Table des matières DVD / Magnétoscope Importantes mesures de sécurité ...................................... 2, 3 Avant l’utilisation ..................................................................... 4 Informations (Appareil, disque, cassette) ......................... 6 , 7 Emplacement des commandes ...................................... 8 ~ 10 Affichages à l’écran et sur le combiné ................................. 11 Raccordements .............................................................
Informations (Appareil, disque, cassette) Protection contre l’effacement Briser la languette. Languette de protection Tournevis Pour enregistrer à nouveau Recouvrir l’ouverture avec du ruban adhésif. Disques DVD-RAM Les disques DVD-RAM doivent remplir les conditions suivantes pour que cet appareil puisse en faire la lecture.
Réglage initial (Raccordements) Données techniques Alimentation: 120 V c.a.
Emplacement des commandes Télécommande Gras: Fonctions magnétoscope Italiques: Fonctions lecteur DVD Gras italiques: Fonctions magnétoscope et lecteur DVD Normal: Autres Éjection / Ouverture / Fermeture Affichage p. 11, 44 p. 20, 22 Mode téléviseur Interrupteur Mode magnétoscope p. 28 Mode DVD p. 28 p. 28 Mode récepteur DSS / câblosélecteur Mode d’entrée p. 35 p. 28 Avance accélérée / repérage / ralenti+ Lecture p. 20, 22 p.
Réglage initial (Raccordements) Panneau de l’appareil Front Viewavant of DECK Gras: Fonctions magnétoscope / Italiques: Fonctions lecteur DVD Gras italiques: Fonctions magnétoscope et lecteur DVD / Normal: Autres Arrêt / Éjection Si le disque ne peut être éjecté p. 20 Avance accélérée / repérage p. 20 Lecture Couper d’abord le contact. Introduire ensuite une petite tige rigide (un trombone déplié par exemple) dans l’orifice sous le plateau. Le plateau devrait se dégager.
Emplacement des commandes (suite) Gras: Fonctions magnétoscope Italiques: Fonctions lecteur DVD Gras italiques: Fonctions magnétoscope et lecteur DVD Panneau arrière Prise d’alimentation c.a. • Une fois l’appareil branché sur le secteur, il consomme 4 W même lorsqu’il n’est pas en marche. Prise de sortie vidéo composante (Y, PB, PR) (DVD seulement) p. 13 Prise de sortie audio analogique 5.1 canaux (centre, extrêmes-graves, ambiophoniques G/D, avant G/D) (DVD seulement) p.
Affichages à l’écran et sur le combiné Affichage des fonctions et des canaux CA 0 8 Indication de bande vierge ou aucun signal émis Sur pression d’une touche de commande, PLAY par exemple, ou lors d’un changement de canal, un affichage apparaît pendant 5 secondes. Affichage de l’état et de l’heure Pour afficher ou supprimer l’affichage de l’écran ci-contre, ➛ appuyer sur DISPLAY.
Raccordements Raccordements de base • Si le téléviseur est muni de prises AUDIO et VIDEO IN, les relier au combiné pour obtenir une meilleure qualité du son et de l’image. • Le raccordement de l’appareil à un amplificateur stéréo permet un rendu stéréophonique même si le téléviseur utilisé est monaural. • Relier le combiné au téléviseur à l’aide d’un câble coaxial RF a (fourni) ou un câble AV b (non fourni) comme le montre la figure ci-dessous.
Possible Impossible • enregistrer • visionner une n’importe quel émission canal (y compris TÉLÉVISEUR diffusée les canaux sur un brouillés). IN OUT canal • effectuer la R brouillé. syntonisation au AUDIO L moyen de la VIDEO télécommande IN OUT sans avoir à VHF/UHF faire appel à la fonction de commande CÂBLOSÉLECTEUR multimarque. ■ Avec câblosélecteur (DVD/Magnétoscope câblosélecteur télé) Antenne ou câble IN FROM ANT.
Raccordements (suite) Raccordements audio Liste des préparatifs Baisser le volume, puis mettre le combiné ainsi que les autres appareils à être raccordés hors circuit avant d’effectuer les raccordements. Ne pas obstruer les orifices de ventilation des appareils et les disposer de façon que l’air circule librement. Lire les instructions avant d’effectuer un raccordement. Bien respecter les codes de couleur lors du raccordement des câbles audio et vidéo.
Réglage initial (Raccordements) ■ Raccordement à un amplificateur (5.1 canaux, ambiophonique) Profiter d’un environnement sonore caractéristique d’une salle de cinéma ou de concert en reproduisant la piste sonore multicanal des DVD à l’aide d’un amplificateur et d’enceintes acoustiques. Deux types de raccordement sont possibles : analogique et numérique. A.
Raccordements/réglage initial (Prêt pour la lecture) Avant réglage initial 1 Mettre le téléviseur sous tension. 2 Voir les raccordements a câble coaxial RF ou b câble AV à la page 12. Régler le téléviseur sur le canal 3. Régler le téléviseur à VIDEO. 3 [DVD/Magnétoscope ➛ Téléviseur] • Aller à “Réglage initial (Prêt pour la lecture)” (voir ci-dessous).
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche VCR de la télécommande et essayer à nouveau. Les réglages sont effectués automatiquement. Les réglages terminés, l’écran ci-dessous s’affiche. 6 /28 / 2003 D I M 2 : 20PM HR ETE : OUI REGLAGE : CA 10 Éjection Mode magnétoscope REGLAGE AUTOMATIQUE DE L’ HORLOGE TERMINE Si le message “REGLAGE AUTOMATIQUE DE L’HORLOGE INCOMPLET” s’affiche, régler l’horloge manuellement. Voir cidessous.
Modification des réglages de la langue d’affichage, 1 2 Appuyer sur ACTION* pour afficher le menu. Langue • Les touches de programmation de la télécommande ne sont pas fonctionnelles lorsque les sorties COMPONENT VIDEO OUT ou S-VIDEO OUT sont utilisées. Sélectionner RF INPUT ou VIDEO INPUT sur le téléviseur et appuyer sur PROG. Canaux 1) Appuyer sur pour sélectionner la rubrique de sélection de la langue.
affichage, du canal, de l’horloge et du canal de sortie Interrupteur *Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche VCR de la télécommande et essayer à nouveau. Mode magnétoscope Touches numériques Réglage du fuseau horaire (Seulement lorsque le réglage de l’horloge a été fait automatiquement.) Action 1) Appuyer sur pour sélectionner “CA SORTIE”, puis appuyer sur SET. Ajout/effacement Sélection Réglage Syntonisation 2) Appuyer sur SET.
Lecture / Enregistrement Éjection Liste des préparatifs Mode magnétoscope Mode DVD Faire tous les raccordements. (pages 12 ~ 15) Brancher le téléviseur et le combiné. Syntoniser le téléviseur sur le canal 3, 4 ou l’entrée vidéo. S’assurer que la télécommande est en mode VCR. (Appuyer sur VCR.) Lecture Avance accélérée/ ralenti+ Pause/ Arrêt sur image Arrêt Rebobinage/ ralenti- Lecture Sélecteur magnétoscope/ télé 1 Insérer une cassette. 2 Appuyer sur PLAY* pour lancer la lecture.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche VCR de la télécommande et essayer à nouveau. Enregistrement 1 2 • Le combiné est mis en marche. Si la commutation automatique VCR/TV (voir page 32) est désactivée, activer le mode magnétoscope à l’aide de la touche VCR/TV sur la télécommande. Appuyer sur CH ou sur les touches numériques pour sélectionner un canal. • Pour l’entrée “LIGNE”, voir à la page 35.
Utilisation de base du DVD Liste des préparatifs Faire tous les raccordements (pages 12 ~ 15). Brancher le combiné. S’assurer que le contact est établi sur la chaîne si le combiné a été raccordé à un amplificateur audio. Ouverture/ Fermeture Interrupteur 1 2 Appuyer sur POWER* sur le combiné ou la télécommande. Appuyer sur DVD pour sélectionner le mode DVD. 3 Appuyer sur OPEN/CLOSE. Placer le disque sur le plateau. 4 Appuyer sur PLAY pour lancer la lecture.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche VCR de la télécommande et essayer à nouveau. ■ Recherche de scène avant/arrière Appuyer sur FF/SLOW+ ou REW/SLOW- en mode lecture. Appuyer sur PLAY pour désactiver. • Amorcer la recherche avant/arrière pendant la lecture d’un CD-Vidéo lancé à partir du menu peut rappeler le menu. • La vitesse de repérage, lente au début, augmente sur chaque pression de la touche. Jusqu’à 5 paliers sont disponibles.
Enregistrement différé Liste des préparatifs Faire tous les raccordements. (pages 12 ~ 15) S’assurer que le combiné et le téléviseur sont branchés et en contact. Régler l’horloge (page 18). S’assurer que la languette de protection est en place sur la cassette (page 6). S’assurer que la télécommande est en mode VCR. (Appuyer sur VCR.) S’assurer que la durée est suffisante pour l’enregistrement sur la bande. 1 2 Appuyer sur PROG* pour appeler l’écran de programmation.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche VCR de la télécommande et essayer à nouveau. Révision, modification ou annulation de la programmation (Aucun enregistrement en cours) 1 2 Appuyer sur PROG pour afficher l’écran de programmation. 3 Remplacement d’un programme... Appuyer sur pour sélectionner un numéro. Appuyer sur SET pour afficher le programme. Recommencer l’étape 2 (page 24) pour entrer un nouveau programme.
Réception d’émissions multivoie/ Système VHS stéréo haute fidélité Raccordement Effectuer les raccordements audio/vidéo comme décrits aux pages 12 à 15. • Même si le téléviseur n’est pas stéréophonique, il est possible d’obtenir un rendu stéréo en reliant le téléviseur à un amplificateur et à des enceintes stéréo. Types de signaux de télédiffusion possibles La liste ci-dessous comporte divers types d’émissions possibles avec leur affichage.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche VCR de la télécommande et essayer à nouveau. Mode audio pour l’enregistrement 1 Appuyer sur AUDIO (SAP/Hi-Fi) pour afficher le mode audio. (L’indication demeure affichée pendant 5 secondes.) 2 Appuyer à répétition sur AUDIO (SAP/Hi-Fi) pour sélectionner le mode voulu. • Se reporter à la section “Types de signaux de télédiffusion”. (Voir à la page 26.) • La flèche indique la sélection. 3 Faire un enregistrement.
Fonction de commande multimarque Programmation de la fonction de commande multimarque Interrupteur Mode magnétoscope Mode récepteur DSS/ câblosélecteur Il est possible de programmer la télécommande en vue de contrôler les fonctions de certains téléviseurs, câblosélecteurs et récepteurs DSS. 1 2 Repérer, à la page suivante, le code correspondant au téléviseur, câblosélecteur ou récepteur DSS utilisé. Mode téléviseur, ➛ ➛ maintenir enfoncée la touche TV, entrer le code au moyen des touches numériques.
Numéros de code des marques de téléviseurs Panasonic ....................... 01, Quasar ............................ 01, RCA ....................................... GE ......................................... Zenith .................................... Magnavox .............................. 02 02 03 03 04 05 Sylvania ................................ Sharp ............................... 06, Sony ...................................... Toshiba ................................. Sanyo ......................
Fonctionnement Système de repérage À chaque enregistrement, un signal d’index est enregistré sur la bande. Lors d’un enregistrement différé, un index est assigné au programme et des informations sont également enregistrées. Les signaux d’index sont par la suite utilisés pour le repérage et le balayage des séquences.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche VCR de la télécommande et essayer à nouveau. Fonctions automatiques Lecture automatique Insertion d’une cassette ➛ Mise en marche automatique ➛ La lecture s’amorce si la languette de protection (page 6) a été rompue. Rebobinage automatique Lecture Avance accélérée ➛ Fin de ➛ Rebobinage bande Rebobinage/ ralenti- Éjection automatique après lecture (La lecture en reprise doit être réglée à “NON”.
Fonctionnement (suite) Sélecteur magnétoscope/télé Lecture en reprise Pour répéter plusieurs fois la lecture d’un même enregistrement. Appuyer sur ACTION* pour afficher le menu. 1 2 Appuyer sur pour sélectionner “REGLAGE MAGNETOSCOPE”, puis appuyer sur SET. 3 Appuyer sur pour sélectionner “REPRISE LECTURE”, puis appuyer sur SET pour sélectionner “OUI” ou “NON”. La sélection magnétoscope/télé peut être effectuée automatiquement ou manuellement. 1 2 Appuyer sur ACTION pour afficher le menu.
Caractéristiques spéciales Affichage *Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche VCR de la télécommande et essayer à nouveau. Avis de signal faible Lorsque “OUI” est sélectionné, une image est affichée indépendamment de la qualité du signal. 1 2 Arrêt Appuyer sur ACTION pour afficher le menu. Appuyer sur pour sélectionner “REGLAGE CANAL”, puis appuyer sur SET.
Caractéristiques spéciales (suite) Avertisseur d’erreur sur télécommande Si la fonction de commande multimarque (page 28) est utilisée et que cet avertisseur est activé, un message d’erreur est affiché chaque fois qu’une touche invalide est pressée en mode téléviseur, récepteur DSS ou câblosélecteur. 1 2 *Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche VCR de la télécommande et essayer à nouveau. Mode d’entrée Appuyer sur ACTION* pour afficher le menu.
Copie d’un enregistrement (duplication) Raccordement Magnétoscope/ Caméscope (HiFi) DVD/Magnétoscope OUT VIDEO AUDIO 1 2 L R OUT IN 1 VIDEO L AUDIO1 R Téléviseur Avant du combiné VIDEO IN 2 IN FROM ANT. (Prises d’entrée audio/ vidéo également disponibles à l’avant) VHF/ UHF VHF/UHF OUT TO TV L-AUDIO IN2-R Relier la prise VIDEO OUT du magnétoscope de lecture à la prise VIDEO IN du combiné. Pour visionner l’enregistrement pendant sa duplication, raccorder un téléviseur de la manière illustrée.
Utilisation du disque Langue des sous-titres (DVD-Vidéo seulement) Il est possible de sélectionner une langue (dans la mesure où elle est disponible) pour les sous-titres autre que celle réglée aux réglages initiaux du DVD. (Voir à la page 53.) 1 Appuyer sur SUB TITLE* en mode lecture pour afficher la sélection de langue des sous-titres. Liste des préparatifs Lire la section “Utilisation de base du DVD” à la page 22.
*Important : Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche DVD de la télécommande et essayer à nouveau. Lorsque apparaît sur l’écran lors d’une pression sur une touche, cela signifie que l’action correspondante n’est pas possible sur le disque ou sur le combiné. Visionnement à angles multiples (DVD seulement) Certains disques DVD comportent des scènes enregistrées sous divers angles de prise de vue.
Utilisation du disque (suite) Menu de titres (DVD seulement) Il peut arriver que certains disques DVD comportent plus d’un titre (film). Si un menu des titres est disponible, il est alors possible de choisir le numéro du titre voulu. (Il est à noter que l’opération peut varier selon le disque.) Appuyer sur TITLE* en mode lecture pour afficher le menu de titres. 1 2 Appuyer sur ou sur les touches numériques pour sélectionner un titre. Appuyer sur SET ou PLAY pour amorcer la lecture.
*Important : Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche DVD de la télécommande et essayer à nouveau. Lecture programmée (CD-Vidéo/CD) Il est possible de programmer la lecture des plages et leur ordre de lecture. 1 2 Appuyer sur ACTION pour afficher le menu. Appuyer sur pour sélectionner “MODE DE LECTURE”. Appuyer sur SET pour afficher. 3 Liste des préparatifs S’assurer que le combiné est en mode DVD en appuyant sur DVD.
Utilisation du disque (suite) Lecture aléatoire (CD-Vidéo/CD) Les plages sont lues dans un ordre aléatoire. 1 2 Liste des préparatifs S’assurer que le combiné est en mode DVD en appuyant sur DVD. Appuyer sur ACTION* pour afficher le menu. Appuyer sur pour sélectionner “MODE DE LECTURE”. Appuyer sur SET pour afficher. Affichage Arrêt 3 MODE DE LECTURE SEL. REGLER FIN : : SET : ACTION Appuyer sur pour sélectionner “LECTURE ALEATOIRE”. Appuyer sur SET pour amorcer la lecture dans un ordre aléatoire.
*Important : Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche DVD de la télécommande et essayer à nouveau. Opération avec disque DVD-Audio Ce combiné, muni d’un convertisseur audio numérique-analogique 192 kHz/24 bits, peut prendre en charge les disques DVD-Audio avec enregistrements sonores de haute qualité. La fonctionnalité DVD-Audio comporte les fonctions “Saut d’images fixes” et “Lecture de groupes en prime”. (Voir ci-dessous.
Opération avec disque DVD-RAM (DVD-RAM seulement) Ce combiné prend en charge les disques DVD-RAM enregistrés et édités par l’utilisateur. Nota • Aucun enregistrement sur DVD-RAM n’est possible sur ce combiné. Lecture d’un DVD-RAM 1 2 Suivre les étapes 1 à 3 à la page 22. • La lecture s’amorce à partir du premier titre de programme enregistré sur le DVD-RAM.
*Important : Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche DVD de la télécommande et essayer à nouveau. Play List (Liste de lecture) Si le disque DVD-RAM comporte une liste de lecture, la liste de lecture des titres présélectionnés par l’utilisateur s’affiche en vue d’en faciliter l’accès. (L’opération peut varier selon le mode d’édition du DVD-RAM.) 1 2 Appuyer sur MENU en mode lecture/arrêt pour afficher la liste de lecture.
Fonctionnement du lecteur DVD à partir des affichages à l’écran Sur pression de la touche DISPLAY, des affichages donnent des informations sur le disque (titre/numéro de chapitre/plage et temps écoulé) de même que des informations sur l’état du combiné (lecture en reprise, mode de lecture). 1 Liste des préparatifs S’assurer que le combiné est en mode DVD en appuyant sur DVD. Appuyer sur DISPLAY* en mode lecture ou arrêt pour activer les affichages à l’écran.
*Important : Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche DVD de la télécommande et essayer à nouveau. Description détaillée des écrans ■ Écran d’informations sur le disque (pour DVD-Vidéo) 1. N° de titre 1 2 T I TRE : 1 CHAPITRE : 12 DVD 01 : 23: 45 3 4 • Sélectionner “TITRE” et appuyer sur SET. • Changer le numéro en appuyant sur ou au moyen des touches numériques, puis appuyer sur SET. 2. N° de chapitre SEL. : REGLER: SET • Sélectionner “CHAPITRE” et appuyer sur SET.
Fonctionnement du lecteur DVD à partir des affichages à l’écran (suite) ■ Écran d’informations sur le disque (pour CD-Vidéo/CD) 1. N° de plage 1 2 • Sélectionner “TITRE” et appuyer sur SET* . ou au moyen des • Changer le numéro en appuyant sur touches numériques, puis appuyer sur SET. TITRE PBC : 1 : NON CD VIDEO 01 : 23: 45 3 4 2. Pilotage de la lecture [CD-Vidéo avec pilotage de la lecture seulement] REGLER: SET SUIVANT : DISPLAY OUI Le menu de lecture du disque est affiché.
*Important : Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche DVD de la télécommande et essayer à nouveau. ■ Écran d’informations sur le combiné (pour combiné DVD/Magnétoscope) 1. Lecture en reprise • Sélectionner “REPRISE” et appuyer sur SET. • Pour changer le mode pendant la lecture, appuyer sur DVD-Vidéo CHAPITRE DVD-Audio PLAGE DVD-RAM (PROGRAMME) PROGRAMME (PLAY LIST) PLAY LIST CD-Vidéo/CD PLAGE , puis appuyer sur SET.
Fonctionnement du lecteur DVD à partir des affichages à l’écran (suite) Pour référence • Lecture en reprise d’un chapitre ou d’un titre (DVD-Vidéo) En cours de lecture TITRE chapitre chapitre chapitre REPRISE DE CHAPITRE REPRISE DE TITRE LECTURE NORMALE • Lecture en reprise d’une plage ou d’un groupe (DVD-Audio) Ouverture / Fermeture En cours de lecture GROUPE GROUPE plage plage plage plage plage plage Interrupteur Lecture Rebobinage/ Avance accélérée Pause Arrêt Touches numériques REPRISE DE
Lecture de fichiers MP3/WMA/JPEG Cet appareil peut prendre en charge des CD-R et des Lecture de fichiers MP3/WMA CD-RW avec fichiers au format MP3/WMA/JPEG enregistrés sur un ordinateur et destinés à un usage Suivre les étapes 1 à 3 ci-contre. personnel. Il se pourrait toutefois que certains disques ne Appuyer sur pour sélectionner un puissent être lus en raison des conditions d’enregistrement. fichier MP3/WMA ( / ). Appuyer sur la touche POWER* de la (à partir du mode arrêt) télécommande ou du combiné.
Lecture de fichiers MP3/WMA/JPEG (suite) Lecture de fichiers JPEG Il est possible de visionner des images au format JPEG. Grandeur des images: 32x32~7680x7680 pixels Nota • Il se pourrait que certains fichiers JPEG ne puissent être pris en charge. Suivre les étapes 1 à 3 à la page 49. 1 2 Appuyer sur pour sélectionner un fichier JPEG ( ). Appuyer sur SET ou PLAY. Le fichier JPEG sélectionné s’affiche. [Écran de lecture JPEG] ■ Retour au menu MP3/WMA/JPEG ➡ Appuyer sur STOP. (voir p.
Zoom sur images JPEG (Pendant la lecture de fichiers JPEG) Il est possible, pendant la lecture d’un fichier JPEG, d’agrandir des parties d’une image JPEG et de sélectionner le taux d’agrandissement à l’aide de la touche ZOOM de la télécommande. Réglage du taux d’agrandissement Appuyer sur ZOOM à répétition pour modifier l’affichage comme suit. ➡ Appuyer sur STOP pour rappeler le menu MP3/ Lecture Rebobinage/ ralenti- WMA/JPEG.
Fonction de verrouillage du DVD Il est possible de bloquer le visionnement de certains DVD non recommandables pour de jeunes auditoires. • Certains DVD sont codés pour la protection de certains publics sensibles. Si le niveau de protection autorisé est plus élevé que celui que vous avez préréglé, la lecture sera impossible. Verrouillage DVD (DVD seulement) Il faut entrer un code à 4 chiffres pour pouvoir visionner un programme verrouillé ou pour changer les réglages de restriction.
Réglages initiaux du DVD 1 2 Appuyer sur ACTION pour afficher le menu. pour Appuyer sur sélectionner une rubrique. Appuyer sur SET. Le paramétrage demeure en mémoire (même après coupure du contact) jusqu’à ce qu’il soit modifié. Cela signifie que le combiné fonctionne toujours selon les mêmes paramètres (surtout avec des disques DVD). Liste des préparatifs S’assurer que le combiné est en mode DVD en appuyant sur DVD.
Réglages initiaux du DVD (suite) Sortie audio Liste des préparatifs Sélectionner le type de signal audio numérique devant être transmis à la prise de sortie audio numérique optique du combiné. 1 2 Appuyer sur ACTION* pour afficher le menu. Appuyer sur pour sélectionner “SORTIE AUDIO”. Appuyer sur SET pour afficher. 3 S’assurer que le combiné est en mode DVD en appuyant sur DVD.
*Important : Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche DVD de la télécommande et essayer à nouveau. Configuration des enceintes Fixer le nombres d’enceintes raccordées au recépteur (amplificateur, décodeur.) (Voir aux pages 14 et 15.) 1 Suivre les étapes 1 à 3 à la page 54. 2 SORTIE AUDIO LPCM(DVD) : NON Dolby Digital : Bitstream dts : Bitstream DRC : NON REGLAGE ENCEINTES SEL.
Réglages initiaux du DVD (suite) Équilibre de sortie Régler le niveau de sortie sur les enceintes. Pour ce faire, faire entendre un disque ou activer “SIGNAL D’ESSAI” (p. 57). Effectuer alors le réglage pendant l’écoute. (Même si la valeur “NON” a été sélectionnée dans le menu de configuration “TAILLE ENCEINTES”, il est néanmoins possible de régler l’équilibre de sortie.) 1 Suivre les étapes 1 et 2 à la page 55 (“Configuration des enceintes”).
*Important : Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche DVD de la télécommande et essayer à nouveau. Configuration avec signal d’essai Cette fonction permet d’effectuer le réglage de l’équilibre de sortie des enceintes. En commençant par l’enceinte avant gauche, un signal est émis sur les enceintes dans le sens horaire. Pendant l’émission du signal, régler le niveau de sortie sur l’enceinte de canal centre et sur les enceintes ambiophoniques (D/G).
Liste des codes de langue Entrer le numéro de code voulu pour le réglage initial de “Audio”, “Sous-titres” et/ou “Menu” (Voir page 53).
Avertissements et directives Ces affichages indiquent une erreur d’opération ou donnent des instructions supplémentaires.
Guide de dépannage Vérifier les points suivants si le combiné présente des problèmes de fonctionnement. Alimentation Solution Pas d’alimentation... Le contact est automatiquement coupé… Enregistrement et lecture Les émissions télévisées ne peuvent pas être enregistrées... L’enregistrement différé ne peut se faire... Il n’y a pas d’image à la lecture ou l’image est parasitée ou comporte des lignes...
Vérifier les points suivants si le combiné présente des problèmes de fonctionnement.
Garantie Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 Certificat de garantie limitée Panasonic Panasonic Canada Inc. garantit cet appareil contre tout vice de fabrication et accepte, le cas échéant, de remédier à toute défectuosité pendant la période indiquée ci-dessous et commençant à partir de la date d’achat original.
Liste des centres de service RÉPARATION SOUS GARANTIE Pour de l’aide sur le fonctionnement de l’appareil ou pour toute demande d’information, veuillez contacter votre détaillant ou notre service à la clientèle au: N° de téléphone: N° de télécopieur: Site Internet: (905) 624-5505 (905) 238-2360 www.panasonic.
Index Réglage automatique à l’heure avancée (d’été) .................... 19 Lecteur & magnétoscope Réglage initial (Prêt pour la lecture) ................................ 16, 17 Réinitialisation de toutes les fonctions en mémoire ............... 9 A Accessoires .............................................................................. 4 Révision, modification ou annulation de la programmation .. 25 Affichages à l’écran (Magnétoscope) ....................................