Initial Setup TV / DVD / VCR Combination Operating Instructions PV-DF2003-K/PV-DF2703-K Basic Operation Model No. TV Operation MULTI FORMAT PLAYBACK *Ability to play back may depend on recording conditions. As an ENERGY STAR ® Participant, Panasonic has determined that this product or product model meets the ENERGY STAR ® guidelines for energy efficiency. This operating instruction book is designed for use with models PV-DF2003-K and PV-DF2703-K. Illustrations in this manual show the PV-DF2703-K.
Important Safeguards and Precautions READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON UNIT INSTALLATION 1 POWER SOURCE CAUTION Operate only from power source indicated on unit or in this manual. If uncertain, have your Electric Utility Service Company or Video Products Dealer verify your home power source. 2 POWER CORD PLUG For safety, this unit has a polarized type plug (one wide blade), or a three-wire grounding type plug.
Safety Precautions Warning : To prevent fire or shock hazard, do not expose this equipment to rain or moisture. Caution : To prevent electric shock, match wide blade of plug to wide slot, fully insert. This video recorder, equipped with the HQ (High Quality) System, is compatible with existing VHS equipment. Only use those tapes with the mark. It is recommended that only cassette tapes that have been tested and inspected for use in 2, 4, 6, and 8 hour VCR machines be used.
Before Using Congratulations Loading the Batteries On your purchase of one of the most sophisticated and reliable products on the market today. Used properly, it will bring you and your family years of enjoyment. Please fill in the information below. The serial number is on the tag located on the back of your unit. 1) Open the cover. 2) Insert batteries as marked. Date of Purchase Dealer Purchased From Dealer Address 3) Close the cover. Dealer Phone No. Model No. Serial No.
Table of Contents TV / VCR Playback a Tape.............................................................................................................20 Record On a Tape..........................................................................................................20 Copy Your Tapes (Dubbing) .........................................................................................21 Basic DVD Operation .............................................................................................
Unit & Cassette Information Features for a Quality Picture Head Cleaning Playing older or damaged tapes may eventually cause video heads to become clogged. Head Clog Sensor During playback this screen appears if clogging is detected. To clear message from screen, press PLAY on the remote or unit. V I DEO HEADS MAY NEED CLEAN I NG PL EASE I NSERT HEAD CLEAN I NG CASSETTE OR REFER TO MANUAL Digital Auto Tracking Continuously analyzes the signal and adjusts for optimum picture quality.
Specifications Picture Tube 20 inch measured diagonal pure flat Picture Tube (PV-DF2003-K) 27 inch measured diagonal pure flat Picture Tube (PV-DF2703-K) VCR Video Recording System 4 rotary heads helical scanning system 1 track (Normal) Audio Track 2 channel (Hi-Fi Audio Sound) Tuner Broadcast Channels VHF 2 ~ 13, UHF 14 ~ 69 Midband A through I (14 ~ 22) Superband J through W (23 ~ 36) Hyperband AA ~ EEE (37 ~ 64) CABLE Channels Lowband A-5 ~ A-1 (95 ~ 99) Special CABLE channel 5A (01) Ultraband 65 ~ 94,
Disc Information Discs that can be played Disc type DVD-Video DVD-R DVD-RAM Disc Logo Disc formats supported by this unit • DVD-Video format • DVD-Video formatted discs (finalized*) It may not be possible to play these discs in all cases due to the type of disc or condition of the recording. • Version 1.1 of the Video Recording Format a unified video recording standard. Video CD • Video-CD format CD-DA • CD-DA format CD-R • CD-DA format • Video-CD format • MP3/WMA/JPEG file and finalized*.
Definition of Terms Angle Some DVD discs feature scenes simultaneously shot from different angles. The ANGLE button can be used to view the scene from different angles. (ANGLE Indicator lights up on the unit when a scene recorded at different angles is detected.) • Sticking a label on the disc may impair DVD-R playback. • Do not attach sticker to discs. (Do not use discs with exposed adhesive from tape or left over peeled-off stickers.) • Only hold disc by edges as shown below.
Location of Controls Remote Control Buttons EJECT/OPEN/CLOSE See next page. DVD Sets to DVD mode. POWER Turns the unit on or off. LIGHT See next page. DSS/CABLE Sets the remote to control some basic DSS or Cable box functions. TV/VCR Sets to TV/VCR mode. MUTE Mutes the sound instantly. FM Receives FM radio signal. CHANNEL UP/DOWN Selects a channel. VOLUME UP/DOWN Adjusts volume. SURROUND Creates a deeper, 3-D sound effect. ANGLE Selects the desired angle in DVD mode.
LIGHT button: EJECT/OPEN/CLOSE button: When this button is pressed in TV-VCR mode, the tape is ejected. This button is inoperative if pressed during recording. If pressed in DVD mode, the disc tray opens or closes. Initial Setup When LIGHT is pressed, (DVD, , DSS/CABLE, CH UP/DOWN, VOL UP/DOWN) buttons will light for 5 seconds for easy button location. If no button is pressed in 5 seconds, the light goes out to conserve the batteries.
Location of Controls (continued) Front View of the unit Built In Speaker If the disc cannot be removed, First unplug unit. Then, prepare a rigid wire (e.g. an extended paper clip, etc.) and, applying moderate force, insert it straight into the hole at the base of the tray. The tray will eject a little. Now, pull the tray all the way out and remove the disc. Disc Tray Phones Jack Connect an earphone or headphones.
Rear View of the unit Audio/Video Input Connector 1 (LINE 1) Connect from other component. Audio Output Connector (L/R) Pg. 14 Optical digital audio output connector Pg. 14 Initial Setup VHF/UHF Antenna Input Terminal See below. AC Power Plug When plugged into an AC outlet, this unit consumes 3.5 W of electric power in OFF condition. S-Video Input Connector 1 (LINE 1) Connect from other component with S-Video. Connections For ANT.
Connections (continued) Audio connections Enjoy the powerful movie theatre and hall-like sound available with multiple channel audio found on DVDs by connecting an amplifier and speakers. There are two types of connection, digital and analog. ■ Digital connection ■ Analog connection Connect an amplifier with Dolby Digital and DTS decoders to enjoy surround sound.
IMPORTANT NOTE: Check List Enjoying digital audio output from the digital audio output connector Notes on audio output from the optical digital audio output connector Disc Sound recording format Dolby Digital DVD Linear PCM (48/96 kHz 16/20/24 bit) dts Video CD MPEG 1 CD Linear PCM MP3 MP3 WMA WMA Optical digital audio output from connector Dolby Digital bitstream (1-5.
Initial Setup (Ready to Play) Please make all cable or antenna connections before powering on. Initial Setup (Ready to Play) Press 1 on the remote for TV-VCR mode. Plug the unit power cord into an AC wall outlet. EJECT POWER 2 TV-VCR S UR RO UND Press POWER* on the remote or unit. Press CH to select English. OR Press CH to select French (Français). OR Press VOL+ to select Spanish (Español). SELECT SET ACTION Auto channel and clock set starts.
*Important: If a remote control button does not work when pressed, press the remote and try the button again. Manual Clock Set button on the Reset all unit Memory Functions When moving unit to a new location, or if a mistake was made in the Initial Setup section. • Make sure a tape is not inserted in the unit. 1 Press ACTION on the remote to display SET CLOCK Menu screen. Initial Setup If AUTO CLOCK SET was incomplete, manually set the clock as follows.
Reset Language, Channels, Clock, 1 Press ACTION* M A I N MENU DVD LOCK LANGUAGE 53 TV 2 CH CLOCK SELECT : END : ACT I ON to display MAIN MENU. 1 SET : SET ■ Language ■ Channels 1) Press to select language icon. ■ Clock to 1) Press select “CH.” 1) Press to select “CLOCK.” M A I N MENU M A I N MENU M A I N MENU DVD DVD LOCK LANGUAGE 5 TV 1 CH CLOCK SELECT : END : ACT I ON 3 LOCK LANGUAGE 53 TV CH CLOCK SELECT : END : ACT I ON SET : SET 2) Press SET.
Time Zone Adjust 4) Press and press SET to select and set the month, date, year, time, and DST (Daylight Saving Time). To Make Corrections, repeatedly press to move to error, then correct. 5) Press ACTION twice to start the clock and exit this mode. S UR RO UND ■ Time Zone Adjust Initial Setup *Important: If a remote control button does not work when pressed, press the button on the remote and try the button again. CH (Only when Auto Clock is set.) 1) Press to select “CLOCK.
Playback a Tape Record On a Tape Check List Cable or antenna is connected. Power cord is plugged in. 1 Insert a cassette. • The unit power comes on automatically. Record tab 1 2 3 To prevent tape jam, remove loose or peeling labels from tapes. 2 ■ ➞ ➞ ■ ➞ ➞ ■ ➞ ➞ ■ ➞ ➞ Insert a tape with record tab. • The unit power comes on automatically. Press CH a channel. • For “LINE” input, see bottom of next page. Press SPEED to select recording speed (see page 6).
Copy Your Tapes (Dubbing) *Important: If a remote control button does not work when pressed, press the the button again. Connections you’ll need to make button on the remote and try Recording (Editing) unit Front Back Playing (Source) VCR VIDEO IN2 L-AUDIO IN2-R S-VIDEO IN2 If cables are connected to both connectors (S-VIDEO IN or VIDEO IN), the S-VIDEO signal will be selected automatically. (The S-VIDEO signal has priority.
Basic DVD Operation 1 2 Check List Cable or antenna is connected. Power cord is plugged in. If unit is connected to an audio amplifier, turn the stereo system’s power on. Insert a disc. • If a disc is already inserted, go to step 3. (Depending on the disc, playback may start automatically.) 1) Press OPEN/CLOSE. 2) Place disc into disc tray. OPEN/ CLOSE POWER Press POWER* on the remote or unit. DVD 10 S UR RO UND 1 2 3 NUMBER keys Press PLAY to start play. Disc tray closes automatically.
*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. ■ Forward/Reverse rapid scene search ➞ Press FF/SLOW+ or REW/SLOWduring play. ➞ Press PLAY to release. • Starting forward/reverse search during play started from menu on Video CDs may recall menu. • Search speed, slow at first, increases with each additional press of the button up to 5 levels.
TV Operation 1 *Important: If a remote control button does not work when pressed, press the button on the remote and try the button again. Press POWER* on the remote or unit. Check List Cable or antenna is connected. Power cord is plugged in. 2 CH08 Use CH or NUMBER keys to select a channel. VOL+/VOLPOWER Press VOL + or VOL - to adjust volume.
MTS Broadcast/TV Stereo System Equipped with -TV Noise Reduction for true MTS reproduction. -TV Noise Reduction is required for good stereo separation and audio fidelity. is a registered trademark, and is licensed by Technology Licensing. Receivable Broadcast Types The following are possible audio broadcast types and on-screen displays. The signal being received is indicated with an “ ” mark while the selected audio mode is indicated with an arrow.
Closed Caption System This multi-use system not only allows the hearing impaired to enjoy selected programs, but also makes useful information from TV stations available to everyone. Closed Caption Mode Feature 1 2 Press ACTION* to display MAIN MENU.
*Important: If a remote control button does not work when pressed, press the remote and try the button again. button on the Caption On Mute Feature Closed Caption narration, if available, is displayed when MUTE button is pressed for silence. 1 MUTE Press ACTION to display MAIN MENU.
TV Timer Features ON-TIMER with Alarm Check List The clock is set to the correct time. This unit can be set to automatically power on in one of 4 modes (TV, VCR Playback, FM radio, or DVD/Video CD/CD.) You can also combine the On-Timer with a one minute alarm that gradually increases in volume. 1 2 Press PROG* to display SET PROGRAM screen. SET PROGRAM T I MER PROGRAMM I NG ON T I MER SLEEP T I MER : 00 SELECT : SET : SET END : PROG 3 1) Press to select desired settings.
On-Screen Display (OSD) *Important: If a remote control button does not work when pressed, press the the button again. button on the remote and try TV/VCR Status & Clock Display Press DISPLAY to display or remove the overlay. Function Status S UR RO UND Rec Time Remaining (OTR mode only, see page 20.) Current Time CH08 REC 1 2 : 0 0PM -0 : 1 2 : 3 4 0 : 25 SP STEREO SAP MONO Receivable Broadcast Types (See page 25.) Counter Tape Speed (See page 6.
FM Radio This unit has an FM radio with built-in antenna, 9 station preset, and a band range of 87.5 ~ 108.1 MHz. You can set the On-Timer (page 28) to wake up to your favourite radio station. FM Radio Setup 1 Press FM* on the remote or TV/FM on the unit to display FM radio mode. 2 1 2 : 0 0PM 3 1 2 : 0 0PM FM 1 FM 1 Press a NUMBER key (1~9) to select the FM preset number. 87. 5MHz 1) Press CH to select the desired radio station. (Each 8 7.
*Important: If a remote control button does not work when pressed, press the FM button on the remote and try the button again. 3 TV-VCR DVD to 1) Press select FM ANTENNA. 2) Press SET to select “INT SET : SET SELECT : (INTERNAL)” or END : ACT I ON “EXT (EXTERNAL)” to ■ For cable TV users determine which one sounds best.
Timer Recording You can set up to 8 programs to be recorded while you are away. 1 2 Press PROG* to display SET PROGRAM screen. 1) Press to select TIMER PROGRAMMING. 2) Press SET to display screen. SET PROGRAM T I MER PROGRAMM I NG ON T I MER SLEEP T I MER : 00 SELECT : SET : SET END : PROG • If a program is already in memory, press SET to select an unused program number. 3 Check List Cable or antenna is connected. Power cord is plugged in. The clock is set to correct time. The tape is long enough.
*Important: If a remote control button does not work when pressed, press the remote and try the button again. Cancel a Timer Recording: (Recording is in progress) Hold down STOP for a few seconds to cancel the Timer Recording. • Any future daily or weekly recordings will be performed as programmed. button on the Review, Replace or Clear Program Contents : (Recording is not in progress) 1 Repeat steps 1 and 2 on page 32. Press to select the desired program.
Cable Box Universal Remote Control Feature The Remote Control may be set up to control some basic DSS or Cable box functions. The Universal Remote Control Setup 1 Find your DSS box or Cable box Brand Code Number from one of the charts on the next page. 2 Set up remote. Hold down DSS CABLE and press NUMBER keys to enter code. POWER TV-VCR DVD • If code number is 100 or greater, e.g., press 1 - 0 - 2 for 102. DSS CABLE Confirm code entry. Press POWER* to turn selected unit ON or OFF.
*Important: If a remote control button does not work when pressed, press the on the remote and try the button again. , DVD, FM button DSS Brand Code Numbers Toshiba.................................................................90 Hitachi/ Hughes..............................................91, 99 Primestar..............................................................92 Drake....................................................................93 Magnavox....................................................
Tape Operation Search System is ... Each time a recording is made, an invisible index mark is placed on the tape. When timer recordings are made, program index and information are also included. These index marks can be used to access or scan recordings. Repeat Play Set to see a recording over and over. PLAY REPEAT ON Index Search Go directly to the desired recording.
*Important: If a remote control button does not work when pressed, press the remote and try the button again. button on the Auto Operation Functions ■ Auto Shut Off No broadcast signal in TV mode (Only when Weak Signal Display is set to OFF.), DVD stops, or blank tape is played for 5 minutes. ➞ Power turns off S UR RO UND • This feature is cancelled if any button is pressed during above conditions.
Special VCR Features Weak Signal Display Feature When “ON” is selected, the picture is displayed even when a broadcast signal is weak or non-existent. 1 Press ACTION* to display MAIN MENU. 2 LOCK LANGUAGE 53 TV CLOCK SELECT : END : ACT I ON 1 CH SET : SET SET UP CHANNEL ANTENNA : CABLE AUTO SET WEAK S I GNAL D I SPLAY : OFF SELECT : SET : SET END : ACT I ON to select “CH.” 2) Press SET to display SET UP CHANNEL screen. 1) Press to select WEAK SIGNAL DISPLAY. 2) Press SET to set “ON” or “OFF.
*Important: If a remote control button does not work when pressed, press the remote and try the button again. button on the VCR Lock All operations are prohibited except Timer recording and tape eject. Useful for families with small children. In Stop mode, hold down REC on the unit without a cassette inserted for 7 seconds to turn “ON.” (Please ignore “NO CASSETTE” warning.) Repeat above with or without cassette to turn “OFF.
V-Chip Control Feature V-Chip Control Feature is... Process of V-Chip Control Feature This unit has a built-in V-Chip Control which allows you to block unwanted TV usage based on US MOVIES, US TV PROGRAMS Ratings, Canadian English Language Ratings and Canadian French Language Ratings. Enter Code Setup Blocking Enter Secret Code A 4-digit code must be entered to view a blocked program or change rating settings. Press ACTION* to display MAIN MENU.
*Important: If a remote control button does not work when pressed, press the remote and try the button again. If LOCK menu is not displayed, perform “Enter Secret Code” steps on page 40. US MOVIES Ratings 1 LOCK US MOV I ES : OFF CHANGE SETT I NGS : OFF US TV PROGRAMS CHANGE SETT I NGS DVD LOCK : OFF CHANGE SETT I NGS NEXT PAGE SELECT : SET : SET END : ACT I ON 1) Press to select US MOVIES. 2) Press SET to set “ON” or “OFF.
V-Chip Control Feature (continued) If LOCK menu is not displayed, do “Enter Secret Code” steps on page 40. Process of V-Chip Control Feature US TV PROGRAMS Ratings US TV PROGRAMS RATINGS: Chart 1 1 LOCK US MOV I ES : OFF CHANGE SETT I NGS US TV PROGRAMS : OFF CHANGE SETT I NGS DVD LOCK : OFF CHANGE SETT I NGS NEXT PAGE SELECT : SET : SET END : ACT I ON 1) Press * to select US TV PROGRAMS. 2) Press SET to set “ON” or “OFF.” ■ “ON” ➞ V-Chip Control is activated. ■ “OFF” ➞ V-Chip Control is deactivated.
*Important: If a remote control button does not work when pressed, press the remote and try the button again. If LOCK menu is not displayed, do “Enter Secret Code” steps on page 40. Canadian English Language Ratings 1 2 LOCK US MOV I ES : OFF CHANGE SETT I NGS US TV PROGRAMS : OFF CHANGE SETT I NGS DVD LOCK : OFF CHANGE SETT I NGS NEXT PAGE SELECT : SET : SET END : ACT I ON 1) Press to select CANADIAN ENGLISH. 2) Press SET to set “ON” or “OFF.
V-Chip Control Feature (continued) If LOCK menu is not displayed, do “Enter Secret Code” steps on page 40. Canadian French Language Ratings 1 2 LOCK US MOV I ES : OFF CHANGE SETT I NGS US TV PROGRAMS : OFF CHANGE SETT I NGS DVD LOCK : OFF CHANGE SETT I NGS NEXT PAGE SELECT : SET : SET END : ACT I ON LOCK CANADIAN ENGLISH : OFF CHANGE SETT I NGS CANADIAN FRENCH : OFF CHANGE SETT I NGS PREVIOUS PAGE SELECT : END : ACT I ON 1) Press * to select NEXT PAGE. 2) Press SET to display screen.
*Important: If a remote control button does not work when pressed, press the remote and try the button again. button on the Process of V-Chip Control Feature Enter Code Setup Blocking Blocking Message • If a program or movie exceeds the ratings you have set, a message will appear on a black background and sound is muted.
Audio Features Audio Mode for Playback Choose the type of sound track for playback. 1 2 See the “Playback a Tape” section on page 20 to playback the tape. H I F I ( L/R) H I F I ( L) H I F I ( R) NORMAL Press AUDIO* repeatedly (each press within 5 seconds) to select desired mode. • This screen appears when you press AUDIO during playback. Audio Mode for Recording Choose audio mode to match recording type.
*Important: If a remote control button does not work when pressed, press the remote and try the button again. DVD Volume Adjust Some DVDs are recorded in lower than average volume levels. For these DVDs, this unit can be set so that the average volume is increased automatically. 1 2 Press ACTION to display MAIN MENU.
Video/Audio Menu This feature allows easy setting of picture and sound suitable for each program source. Audio Menu Video Menu 1 2 Press ACTION* to display MAIN MENU. M A I N MENU LOCK LANGUAGE DVD 53 TV SELECT : END : ACT I ON 3 1) Press to select “SET UP VIDEO/AUDIO.” 2) Press SET to display. SET UP TV 4 SET : SET SET UP V I DEO / AUD I O V I DEO V I DEO AUD I O AUD I O MENU : NORMAL ADJUST MENU : MUS I C ADJUST SELECT : SET : SET END : ACT I ON 1) Press to select “VIDEO MENU.
Video/Audio Adjustment *Important: If a remote control button does not work when pressed, press the and try the button again. Audio Adjustment Video Adjustment 1 2 Press ACTION to display MAIN MENU.
Disc Operation Subtitle Language (DVD only) You can select a different subtitle language (if offered) than the one set at the Settings for DVD Operation. (See page 66.) Check List Please read “Basic DVD Operation” on page 22. Press SUB TITLE* in Play mode to display the subtitle selection on-screen. 1 2 Te amo S UR RO UND • Display disappears after 5 seconds. • When no subtitles are offered, “-” will be displayed instead of the language number. 1) Press to select desired language.
*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Audio Soundtrack Language (DVD only) You can change the audio soundtrack language, selected at the Settings for DVD Operation, to a different language if available. (See page 66.) (This operation works only with discs on which multiple audio soundtrack languages are recorded.) a AUDIO: 1 ENG Dolby Digital 3/2.
Disc Operation (continued) Multiple Angle Viewing (DVD only) DVDs may contain scenes shot from multiple camera angles allowing the same scene to be viewed at different angles. You can view these angles, if available, using the ANGLE button. appears on the screen while a When button is being pressed, it means that the corresponding operation is prohibited by the unit or the disc. Press ANGLE* in Play mode to display the angle selection on-screen. 1 • Display disappears after 5 seconds.
*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Title menu (DVD only) Some DVDs have more than one title, e.g. movies. If the disc offers a title menu, you can select the desired title number. (Operation may vary according to the disc.) 1 S UR RO UND NUMBER keys ANGLE TITLE T I TLE MENU Dogs Cas t l es Love r s B i r ds Press TITLE* in Play mode to display title screen.
Disc Operation (continued) Program Play (Video CD/CD) Check List Unit is in TV-VCR mode, press Video CD or CD is inserted. You can program specific tracks and order of play. 1 2 Press ACTION* in Stop mode to display MAIN MENU. M A I N MENU DVD LOCK LANGUAGE 53 TV 3 SET : SET DVD MAIN MENU 4:3 Pan & Scan SELECT SET END 4 1 6 2 7 3 8 4 9 5 10 Do steps 1 through 6 on this page. Press DISPLAY to display Disc Information screen. (Disc Information Screen) TRACK PBC 1) Press to select “PLAY MODE.
*Important: If a remote control button does not work when pressed, press the the remote and try the button again. , DVD button on Random Play (Video CD/CD) Tracks are played in a random order. 1 M A I N MENU DVD LOCK LANGUAGE 53 TV CH CLOCK SELECT : END : ACT I ON 1 1) Press to select “DVD.” 2) Press SET to display screen. S UR RO UND 2 Press ACTION in Stop mode to display MAIN MENU. CLEAR SET : SET DISPLAY 3 DVD MAIN MENU 4:3 Pan & Scan SELECT SET END 1) Press to select “PLAY MODE.
DVD-RAM Operation (DVD-RAM only) You can enjoy playing your personally recorded/edited DVD-RAM discs on this unit. Note • This unit was designed for playback only. DVD-RAM recording is not possible. Play a DVD-RAM 1 Do steps 1 ~ 2 on page 22. 2 Press TITLE* or MENU to display Direct Navigator or Play List menu for easy title or scene selection. Press STOP to stop playing. 10 S UR RO UND • See below for Direct Navigator or next page for Play List information.
*Important: If a remote control button does not work when pressed, press the the remote and try the button again. , DVD button on Play List If the DVD-RAM features a Play List, your preselected list of favorite scenes is displayed for easy access. (Operation can vary according to how you edited the DVD-RAM.) 1 2 3 Press MENU in Play/Stop mode to display the Play List menu. Press to select a page and press to select a title (Play List No.). Then, press SET or PLAY to start playing.
DVD Operation using On-Screen Displays When DISPLAY is pressed, On-Screen Displays show disc information (title/chapter/track number, elapsed playing time) and unit information (Repeat Play, Play mode). Check List Unit is in DVD mode, press DVD. Press DISPLAY* in Play or Stop mode to display “On-Screen Display.” 1 • Each press of DISPLAY changes the on-screen display as follows. (Please refer to page 59 or 60.
*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again. Detailed Descriptions of Each On-Screen Display ■ Disc information screen (for DVD) 1.TITLE No. 1 2 T I TLE : 1 CHAPTER : 12 DVD 01 : 12 : 55 3 4 • Select “TITLE,” and press SET. • Change the No. by pressing or NUMBER keys, and press SET. 2.Chapter No. • Select “CHAPTER,” and press SET. • Change the No. by pressing or NUMBER keys, and press SET. SELECT : SET : SET 3.
DVD Operation using On-Screen Displays (continued) Detailed Descriptions of Each On-Screen Display ■ Unit information screen • Select “REPEAT”, and press SET*. • Change the desired mode during play by pressing , and press SET. a.
*Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
MP3/WMA/JPEG Playback Operation This unit can play MP3/WMA/JPEG format CD-R or CD-RW recorded for personal use on a PC, etc. Some discs may not play due to recording condition. 1 2 3 ROOT My favorite Press POWER on the remote or unit. Press OPEN/CLOSE, and then place an MP3/WMA/JPEG disc into the disc tray. Press OPEN/CLOSE to close. • MP3/WMA/JPEG menu is displayed. • Playback starts automatically (except JPEG files). • CD directory is displayed. CAR1.jpg CAR2.jpg END_WALTZ.
MP3/WMA Playback JPEG Playback to select an MP3/WMA file 1 (Press/ ) in STOP mode. You can play JPEG images. Displayable Image Size: 32x32~7680x7680 pixels 2 • Some JPEG format may not be played back. Do steps 1~3 on page 62. Press SET or PLAY to start playback. ■ Forward/Reverse Search Press FF/SLOW+ or REW/SLOW- during play. Press PLAY to release. • Search speed, slow at first, increases with each additional press of the button up to 5 levels. ■ Forward/Reverse Track Skip | or SKIP- | during play.
MP3/WMA/JPEG Playback Operation (continued) JPEG Playback - Slide-show - JPEG Playback - Zoom (During JPEG Playback.) You can enlarge specific portions of a JPEG picture and select the zoom ratio using the ZOOM button on the remote. Set Zoom size. Press ZOOM repeatedly to change display as follows. Press STOP to return to the MP3/WMA/JPEG MENU. • You can enlarge the centre portion of the image to one of 2 magnifications. • Operation can be done during Rotation (below). X 1.0 (ORIGINAL) X 1.
DVD Lock Feature *Important: If a remote control button does not work when pressed, press the , DVD button on the remote and try the button again. You can prevent playback of DVDs with a specific rating level which may be unsuitable for children. • Some DVDs are encoded with a rating level. If the disc rating is higher (stricter) than the one you preset, playback will be prohibited. Caution Discs not encoded with a rating level will play even if the jacket states it is for mature audiences.
Settings for DVD Operation 1 2 Press ACTION* in Stop mode to display MAIN MENU. M A I N MENU DVD LOCK LANGUAGE 53 TV 3 CH CLOCK SELECT : END : ACT I ON 1 DVD MAIN MENU Check List Unit is in TV-VCR mode, press SET : SET DISC LANGUAGES AUDIO OUTPUT ST I L L MODE : AUTO TV MODE : 4 : 3 Pan & Scan SELECT SET END 1) Press to select “DVD.” 2) Press SET to display screen. Once initial settings are done, they remain in memory (even after the power is off) until changed.
*Important: If a remote control button does not work when pressed, press the the remote and try the button again. , DVD button on AUDIO OUTPUT Select the digital output to be output from the optical digital audio output connector of the unit. 1 2 Do steps 1 and 2 on page 66.
Settings for DVD Operation (continued) STILL MODE Set to reduce jitter in a displayed still picture or a motion picture. 1 2 Do steps 1 and 2 on page 66. DVD MAIN MENU DISC LANGUAGES AUDIO OUTPUT ST I L L MODE : AUTO TV MODE : 4 : 3 Pan & Scan 1) Press * to select “STILL MODE.” 2) Press SET repeatedly for mode. (See below) S UR RO UND SELECT SET END *Important: If a remote control button does not work when pressed, press the DVD button on the remote and try the button again.
Language Code List Enter the appropriate code number for the initial settings “AUDIO,” “SUBTITLE” and/or “MENUS” (see page 66).
Before Requesting Service Check the following points once again if you are having trouble with your unit. Power Correction No power… • Completely insert Power Plug into an AC outlet. • Set POWER button to ON. • Auto power-off (shut off) occurs after about 5 min. in DVD mode with no operation, or if there is no broadcast signal in TV or Playback mode. Turn the power back on. (P. 23, 37) Power turns itself off... Monitor Correction • No picture or sound... • • Poor picture with normal • sound...
DVD/Video CD/CD Correction Play fails to start even when PLAY is pressed... Play starts but then stops immediately... Picture is distorted during rapid advance or rapid reverse... No Forward/Reverse search play... Play does not start even when title is selected... Audio soundtrack and/or subtitle language is not the one selected at the initial settings... No subtitles... Alternative audio soundtrack (or subtitle) language cannot be selected... Angle cannot be changed...
Warning and Instruction Displays These displays will alert you of a missed operation or provide further instructions.
Limited Warranty/Servicentre List Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 PANASONIC PRODUCT – LIMITED WARRANTY Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship and agrees to remedy any such defect for a period as stated below from the date of original purchase.
Index TV / VCR A Accessories ................................................. 4 B C D E F 74 AC Power Plug........................................... 13 ACTION button .................................... 10, 18 ADD/DLT/CLEAR button...................... 10, 19 Audio Adjustment ...................................... 49 Audio Auto Gain Control (AGC) ................. 48 AUDIO button ................................ 10, 25, 46 Audio Connections .................................... 14 Audio Features ....
TV / VCR T Table of Contents......................................... 5 Tape Erasure Prevention ............................. 4 Tape Operation .....................................36-37 Timer Program Review, Replace, Clear ..... 33 Timer Recording ........................................ 32 Timer Recording Cancellation ................... 33 Time Zone Adjust....................................... 19 TRACKING/V-LOCK buttons ................. 6, 10 TV Operation .............................................
LSQT0720A Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010 www.panasonic.ca Montréal: 3075 Louis A. Amos, Lachine, Québec H8T 1C4 (514) 633-8684 Toronto: 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-8447 Calgary: 6835 - 8th Street N.E.
Réglage initial Combiné télé/DVD/magnétoscope Manuel d’utilisation PV-DF2003-K/PV-DF2703-K Fonctions de base Modèle Fonctionnement du téléviseur Fonctionnement de la minuterie Fonctions avancées • Les instructions concernant le réglage initial et les raccordements se trouvent aux pages 16 à 17. Lecture multiformat Lecture À titre de participant au programme ENERGY STAR®, Panasonic assure que cet appareil, ou ce modèle, satisfait aux normes d’efficacité énergétique du programme.
Importantes mesures de sécurité Pour votre sécurité, lire et conserver les mesures de sécurité et le manuel d’utilisation. Tenir compte également de toutes les mises en garde indiquées dans le manuel et inscrites sur l’appareil. Installation 1 Mise en garde – Alimentation N’alimenter l’appareil que sur le type de courant indiqué dans ce manuel ou sur l’appareil. Dans le doute, consulter un détaillant ou la compagnie d’électricité.
Mesures de sécurité Avertissement : Afin de prévenir tout risque d’incendie ou de chocs électriques, ne pas exposer cet appareil à la pluie ou à une humidité excessive. Attention : Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond. Le magnétoscope intégré, muni du système HQ, est compatible avec le matériel VHS. N’utiliser que des cassettes portant la marque .
Avant l’utilisation Félicitations Vous avez arrêté votre choix sur l’un des produits les plus perfectionnés et les plus fiables sur le marché. Utilisé correctement, il ne manquera pas de procurer à vous et à votre famille des années de plaisir. Veuillez prendre le temps de remplir l’encadré ci-dessous. Le numéro de série est inscrit sur l’étiquette apposée sur le panneau arrière de l’appareil.
Table des matières DVD DVD Téléviseur/ Magnétoscope Contrôle du câblosélecteur avec la télécommande multimarque ............................34 Fonctions de défilement ...............................................................................................36 Caractéristiques spéciales ...........................................................................................38 Discrétion parentale .....................................................................................................
Informations (Appareil, cassette) Contrôle de la qualité de l’image Nettoyage des têtes La lecture de bandes usées ou endommagées peut encrasser les têtes vidéo. Têtes vidéo avec système de détection Si les têtes ont besoin d’être nettoyées, l’écran ci-contre apparaît à la lecture d’une cassette. Pour quitter l’écran, appuyer sur la touche PLAY de la télécommande ou de l’appareil.
Affichage Tube image plat de 50,8 cm (20 po), mesuré en diagonale (PV-DF2003-K) Tube image plat de 68,58 cm (27 po), mesuré en diagonale (PV-DF2703-K) Tube image Magnétoscope Système d’enregistrement vidéo Système audio Bloc d’accord Canaux télévisés Canaux câblodistribués Balayage hélicoïdal à 4 têtes rotatives 1 piste (normal) 2 pistes (sonorité stéréo haute fidélité) Réglage initial Spécifications VHF 2 à 13, UHF 14 à 69 Bande moyenne “A” à “I” (14 à 22) Bande supérieure “J” à “W” (23 à 36) Bande h
Informations (Disque) Disques compatibles Formats de disques pris en charge par l’appareil DVD-Vidéo • Format DVD-Vidéo Type Capacité DVD-R • Disques DVD-Vidéo formatés (finalisés*). Il est possible que cet appareil ne puisse lire ces disques en raison du type d’encodage utilisé à l’enregistrement. DVD-RAM • Version 1.1 de Video Recording Format (norme unifiée pour l’enregistrement vidéo).
Précautions de maniement • Ne pas apposer d’étiquettes sur le disque car ceci pourrait nuire à la lecture DVD-R. • Ne pas apposer de collants sur les disques. (Ne pas utiliser de disques sur lesquels des bandes adhésives ou des étiquettes se décollent.) • Tenir le disque par les bords de façon à ne pas laisser de marques de doigt sur la surface. Les marques de doigt, la saleté et les rayures peuvent provoquer des sauts de lecture et de la distorsion. • Ne pas écrire sur le côté portant l’étiquette.
Emplacement des commandes Télécommande Mode DVD Pour passer au mode DVD. Éclairage Voir à la page suivante. Récepteur DSS/câblosélecteur Programmer la télécommande pour commander certaines fonctions de base des récepteurs DSS et des câblosélecteurs. FM Réception radio dans la bande FM. Commande de volume Réglage du volume. Syntonisation rapide Affichage du dernier canal syntonisé. S UR RO UND Éjection/Ouverture/Fermeture Voir à la page suivante. Interrupteur Mise en/hors marche de l’appareil.
Touche d’éclairage: Touche d’éjection/ouverture/fermeture: Sur pression de cette touche dans le mode télé-magnétoscope, la cassette est éjectée. La touche n’a aucun effet si un enregistrement est en cours. Si elle est pressée en mode DVD, le plateau du disque s’ouvre ou se ferme selon le cas. Réglage initial Suite à une pression sur cette touche, les autres touches (DVD, , DSS/CABLE, CH , VOL +/-) s’allument pendant 5 secondes pour faciliter l’opération.
Emplacement des commandes (suite) Panneau avant de l’appareil Haut-parleur incorporé Si le disque ne peut être éjecté Débrancher d’abord le combiné. Ensuite, préparer un fil rigide (par exemple un trombone déplié) et, en appuyant doucement, l’insérer dans le trou à la base du plateau. Le plateau sort légèrement. Maintenant, tirer le plateau complètement et enlever le disque.
Prise de sortie audio (G/D) P. 14 Bornes d’entrée audio/vidéo 1 (LINE1) Pour le raccordement à un autre appareil. Prise de sortie audio optique numérique P. 14 Réglage initial Panneau arrière Prise d’antenne VHF/UHF Voir ci-dessous. Prise d’alimentation c.a. Une fois l’appareil branché sur le secteur, sa consommation d’énergie sera de 3,5 W (avec le contact coupé). Borne d’entrée S-Vidéo 1 (LINE1) Pour le raccordement à un autre appareil avec S-Vidéo.
Raccordements (suite) Raccordements audio Profiter d’un environnement sonore caractéristique d’une salle de cinéma ou de concert en reproduisant la piste sonore multicanal des DVD à l’aide d’un amplificateur et d’enceintes acoustiques. Deux types de raccordement sont possibles : analogique et numérique. ■ Raccordement numérique ■ Raccordement analogique Raccorder l’appareil à un décodeur Dolby Digital ou DTS pour obtenir un rendu ambiophonique.
Sonorité numérique avec connecteur de sortie audio numérique À propos de la sortie audio du connecteur de sortie audio numérique optique Disque Format Sortie audio numérique d’enregistrement optique par le connecteur du son Train de bits Dolby Digital (1-5,1 canaux) ou PCM (échantillonnage de 48 kHz/16 bits uniquement)*1 PCM linéaire (2 canaux) PCM linéaire (échantillonnage de (48/96 kHz 48 kHz/16 bits ou 16/20/24 bits) échantillonnage de 44,1 kHz/16 bits)*2 Train de bits ou PCM DTS (échantillonnage de 48
Réglage initial (Prêt pour la lecture) S’assurer d’effectuer tous les raccordements avant de mettre l’appareil sous tension. Réglage initial (Prêt pour la lecture) Appuyer sur sur la télécommande pour accéder au mode télé-magnétoscope. 1 Brancher le cordon d’alimentation dans une prise. REGLAGE AUTOMATIQUE EN COURS REGLAGE AUTOMATIQUE DE L’HORLOGE EN COURS ANNULER : APP. STOP Sélection Réglage Action Le réglage automatique des canaux et de l’horloge s’amorce.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche télécommande et essayer à nouveau. 1 Appuyer sur ACTION sur la télécommande pour faire afficher le menu REGLAGE HORLOGE. 2 Appuyer sur pour sélectionner le mois et appuyer sur SET pour régler. Régler la date, l’année, l’heure et l’heure avancée (HR ETE) de la même façon. 3 Appuyer deux fois sur ACTION pour mettre l’horloge en marche et quitter.
Modification des réglages de la langue, des canaux, 1 Appuyer sur ACTION* pour afficher l’écran MENU. MENU DVD BLOCAGE LANGUE TELE HORLOGE CANAL 53 SEL. : FIN 2 1 REGLER : SET : ACT I ON ■ Langue ■ Canaux 1) Appuyer sur pour sélectionner “LANGUE”. 1) Appuyer sur pour sélectionner “CANAL”. MENU DVD SEL. : FIN BLOCAGE LANGUE HORLOGE CANAL REGLER : SET 2) Appuyer à répétition sur SET.
de l’horloge et du fuseau horaire *Important: de (Seulement lorsque le réglage de l’horloge a été fait automatiquement.) 1) Appuyer sur pour sélectionner “HORLOGE”. MENU DVD TELE Changement de canal Touches numériques Ajout/ effacement Sélection BLOCAGE LANGUE 53 SEL. : FIN S UR RO UND ■ Fuseau horaire 4) Appuyer sur et sur SET pour sélectionner et régler le mois, la date, l’année, l’heure et l’heure avancée (HR ETE).
Lecture Enregistrement Liste des préparatifs S’assurer que la câblodistribution ou l’antenne est raccordé. Brancher le cordon d’alimentation. 1 Insérer une cassette. • L’appareil est automatiquement mis en marche. Languette de protection Pour éviter que la cassette ne se coince, retirer toute étiquette déchirée ou qui se décolle. 2 ■ ■ ■ ■ 1 2 3 Insérer une cassette munie de sa languette de protection. • L’appareil est automatiquement mis en marche.
Duplication (Copie de cassettes) *Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche télécommande et essayer à nouveau. Raccordements nécessaires de la Télé-magnétoscope d’enregistrement (montage) Arrière Avant Magnétoscope de lecture (source) VIDEO IN2 L-AUDIO IN2-R S-VIDEO IN2 Si des câbles sont connectés aux deux prises (S-VIDEO IN ou VIDEO IN), le signal S-VIDEO sera automatiquement sélectionné. (Le signal S-VIDEO a la priorité.
Utilisation de base du DVD Liste des préparatifs 1 2 Appuyer sur POWER* (sur l’appareil ou la télécommande). S’assurer que la câblodistribution ou l’antenne est raccordé. Brancher le cordon d’alimentation. S’assurer que le contact est établi sur la chaîne si l’appareil a été raccordé à un amplificateur audio. Mettre un disque en place. • Si un disque est déjà en place, passer à l’étape 3. (Certains disques amorcent la lecture automatiquement.) 1)Appuyer sur OPEN/CLOSE. 2)Placer le disque sur le plateau.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche DVD de la télécommande et essayer à nouveau. ■ Avance et recul rapides pour repérage d’une scène ➞ Appuyer sur FF/SLOW+ ou REW/SLOWen mode lecture. ➞ Appuyer sur PLAY pour désactiver. • Amorcer l’avance (ou le recul) rapide pendant la lecture d’un CD-Vidéo lancé à partir du menu peut rappeler le menu. • La vitesse de repérage, lente au début, augmente sur chaque pression de la touche. Jusqu’à 5 paliers sont disponibles.
Visionnement 1 *Important: Appuyer sur POWER* sur l’appareil ou sur la télécommande. Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche de la télécommande et essayer à nouveau. Liste des préparatifs S’assurer que la câblodistribution ou l’antenne est raccordé. Brancher le cordon d’alimentation. 2 CA 08 Utiliser CH ou les touches numériques pour sélectionner un canal. Volume Appuyer sur VOL+ ou VOL- pour régler le volume.
Réception d’émissions multivoie/réception stéréo Cet appareil est équipé d’un réducteur de bruit -TV pour une reproduction multivoie fidèle. Ce réducteur est nécessaire en vue d’assurer une bonne séparation stéréo et une haute fidélité du rendu sonore. est une marque déposée, et fabriqué sous licence de Technology Licensing. Modes de réception possibles La liste ci-dessous comporte les différents modes audio possibles d’émissions télévisées avec leur affichage.
Affichage des sous-titres Ce système permet non seulement aux malentendants de suivre certains programmes, mais aussi la lecture d’informations diffusées par les stations de télévision. Mode affichage des sous-titres 1 2 Appuyer sur ACTION pour afficher l’écran MENU. MENU DVD BLOCAGE LANGUE TELE HORLOGE CANAL 53 SEL. : FIN 3 1 REGLER : SET : ACT I ON REGLAGE TELEV I SEUR SOUS - T I TRES SELECT SOURCE : BLC ACCORD REGLAGE V I DEO / AUD I O REGLAGE VOL. DVD : + 2 ANTENNE FM : I NT.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche télécommande et essayer à nouveau. de la Affichage des sous-titres avec réglage silencieux Sur réception d’une émission avec sous-titrage, une pression de la touche MUTE appelle l’affichage des sous-titres. Réglage silencieux 1 S UR RO UND 2 Appuyer sur ACTION pour afficher l’écran MENU.
Minuterie du téléviseur Mise en contact différée avec alarme Liste des préparatifs Il est possible de programmer la mise en contact automatique en 4 modes (téléviseur, lecture magnétoscope, radio FM, DVD/CD-Vidéo/CD). La mise en contact différée peut également être combinée à une alarme d’une minute dont le volume augmente graduellement. 1 2 L’horloge est réglée. Appuyer sur PROG* pour faire afficher l’écran REGLAGE PROGRAMMATION.
Affichages à l’écran *Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche télécommande et essayer à nouveau. de la Ligne d’état et affichage de l’heure Appuyer sur DISPLAY pour faire apparaître ou disparaître l’affichage.
Radio FM L’appareil possède une radio FM avec antenne intégrée. II est possible de présyntoniser 9 stations dans une bande de fréquence de 87,5 ~ 108,1 MHz. La minuterie de mise en contact différée (page 28) peut également être réglée pour se réveiller au son de la radio. Réglage de la radio FM 1 2 Appuyer sur FM* sur la télécommande ou TV/FM sur le combiné pour afficher l’écran du mode radio FM. Appuyer sur une touche numérique (1 à 9) pour sélectionner une adresse mémoire. 1 2 : 0 0PM FM 1 87.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche FM de la télécommande et essayer à nouveau. 3 REGLAGE TELEV I SEUR SOUS - T I TRES SELECT SOURCE : BLC ACCORD REGLAGE V I DEO / AUD I O REGLAGE VOL. DVD : + 2 ANTENNE FM : I NT. MESSAGE D' ERREUR : OU I REGLER : SET SEL.
Enregistrement différé La mémoire accepte jusqu’à 8 programmes d’enregistrement différé. 1 2 Appuyer sur PROG* pour afficher l’écran REGLAGE PROGRAMMATION. REGLAGE PROGRAMMATION PROGRAMMATION MINUTERIE MINUTERIE MISE S/TENSION MINUTERIE-SOMMEIL : 00 SEL. : REGLER : SET FIN : PROG 1) Appuyer sur pour sélectionner “PROGRAMMATION MINUTERIE”. 2) Appuyer sur SET pour afficher. Liste des préparatifs S’assurer que la câblodistribution ou l’antenne est raccordé. Brancher le cordon d’alimentation.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche télécommande et essayer à nouveau. Annulation d’un enregistrement différé : (Enregistrement en cours) Enfoncer STOP pendant quelques secondes pour annuler l’enregistrement. • Tous les autres enregistrements quotidiens ou hebdomadaires, s’il y a lieu, seront effectués tel que prévu.
Contrôle du câblosélecteur avec la télécommande multimarque pour commander certaines fonctions de base des récepteurs DSS et des câblosélecteurs. Programmation de la télécommande multimarque 1 Trouver, dans les tableaux sur la page suivante, le numéro de code correspondant à la marque du câblosélecteur ou du récepteur DSS. 2 Programmer la télécommande. Tout en appuyant sur DSS CABLE entrer le code au moyen des touches numériques.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche FM de la télécommande et essayer à nouveau. , DVD ou Numéros de code des marques de récepteurs DSS Toshiba.................................................................90 Hitachi/ Hughes..............................................91, 99 Primestar..............................................................92 Drake....................................................................93 Magnavox.......................
Fonctions de défilement Système de repérage ... À chaque enregistrement, un signal d’index est enregistré sur la bande. Lors d’un enregistrement différé, un index est assigné au programme et les informations relatives à l’horodateur sont également enregistrées. Les signaux d’index sont par la suite utilisés pour le repérage et le balayage des séquences. Lecture en reprise Il est possible de répéter plusieurs fois la lecture d’un même enregistrement.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche télécommande et essayer à nouveau. de la Fonctions automatiques ■ Coupure automatique du contact Si aucun signal n’est émis en mode télé (seulement lorsque l’avis de signal faible est réglé sur NON) ou si le lecteur DVD est en mode arrêt pendant 5 minutes : ➞ Le contact se coupe automatiquement. • Cette fonction est désactivée dans le cas où une touche est pressée dans un des modes mentionnés ci-dessus.
Caractéristiques spéciales Avis de signal faible Lorsque “OUI” est sélectionné, une image est affichée même si le signal capté est faible ou qu’aucun signal n’est émis sur le canal syntonisé. 1 2 Liste des préparatifs Il est nécessaire de sélectionner le mode télé en appuyant sur avant de sélectionner “CANAL” dans le menu. Appuyer sur ACTION* pour afficher l’écran MENU. MENU DVD BLOCAGE LANGUE TELE HORLOGE CANAL 53 SEL. : FIN 1 REGLER : SET : ACT I ON 1) Appuyer sur pour sélectionner “CANAL”.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche télécommande et essayer à nouveau. de la Verrouillage du magnétoscope Lorsque cette fonction est activée, aucune opération, sauf l’enregistrement différé et l’éjection de la cassette, n’est possible. Cela s’avère particulièrement utile pour des parents ayant de jeunes enfants. En mode arrêt, maintenir enfoncée la touche REC sur le combiné pendant 7 secondes, sans cassette dans l’appareil, pour activer cette fonction.
Discrétion parentale Fonction de discrétion parentale (puce antiviolence) Le combiné est équipé d’une fonction de discrétion parentale qui permet de bloquer la réception d’émissions et de films de classifications américaines, canadiennes ou québécoises. Séquence des réglages Entrer code Réglages Blocage Entrer le mot de passe Un code à 4 chiffres doit être entré pour permettre le visionnement d’une émission “bloquée” ou pour changer le réglage de la classification.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche télécommande et essayer à nouveau. Si le menu BLOCAGE n’est pas affiché, se reporter à la section “Entrer le mot de passe” à la page 40. Classifications des films américains 1 1) Appuyer sur pour sélectionner “FILMS USA”. 2) Appuyer sur SET pour régler “OUI” ou “NON”. ■ “OUI” ➞ la fonction de discrétion parentale est activée. ■ “NON” ➞ la fonction de discrétion parentale est désactivée.
Discrétion parentale (suite) Si le menu BLOCAGE n’est pas affiché, se reporter à la section “Entrer le mot de passe” à la page 40. Classifications des émissions télé américaines 1) Appuyer sur * pour sélectionner “EMISSIONS TELE USA”. 2) Appuyer sur SET pour régler “OUI” ou “NON”. 1 ■ “OUI” ➞ la fonction de discrétion parentale est activée. ■ “NON” ➞ la fonction de discrétion parentale est désactivée. 1) Appuyer sur pour sélectionner “MODIFIER REGLAGE”. 2) Appuyer sur SET pour appeler l’affichage.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche télécommande et essayer à nouveau. de la Si le menu BLOCAGE n’est pas affiché, se reporter à la section “Entrer le mot de passe” à la page 40. Séquence des réglages Classifications canadiennes Classifications canadiennes 1 2 1) Appuyer sur pour sélectionner “PAGE SUIVANTE”. 2) Appuyer sur SET pour appeler l’affichage. 1) Appuyer sur pour sélectionner “CANADA”. 2) Appuyer sur SET pour régler “OUI” ou “NON”.
Discrétion parentale (suite) Si le menu BLOCAGE n’est pas affiché, se reporter à la section “Entrer le mot de passe” à la page 40. Classifications québécoises 1 2 * 1) Appuyer sur pour sélectionner “PAGE SUIVANTE”. 2) Appuyer sur SET pour appeler l’affichage. 1) Appuyer sur pour sélectionner “CANADA-QUEBEC”. 2) Appuyer sur SET pour régler “OUI” ou “NON”. ■ “OUI” ➞ la fonction de discrétion parentale est activée. ■ “NON” ➞ la fonction de discrétion parentale est désactivée.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche télécommande et essayer à nouveau. de la Séquence des réglages Entrer code Réglages Blocage Message de blocage • Si la cote d’un film ou d’une émission dépasse la cote sélectionnée, un message s’affiche sur fond noir et le son est mis en sourdine.
Caractéristiques audio Mode audio pour la lecture Sélectionner le mode audio pour la lecture. 1 2 Voir la section “Lecture” à la page 20 pour effectuer la lecture de la cassette. H I F I ( G/D) H I F I ( G) H I F I ( D) NORMAL Appuyer à répétition sur AUDIO* (chaque pression dans un délai de 5 secondes) pour sélectionner le mode désiré. Mode audio pour I’enregistrement Sélectionner le mode audio correspondant au type du programme à enregistrer.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche télécommande et essayer à nouveau. Réglage du volume DVD Sur certains DVD, la piste sonore est enregistrée à un volume plus bas que d’ordinaire. Pour ces DVD, il est possible de paramétrer l’appareil de manière que le volume moyen soit automatiquement monté. 1 2 Appuyer sur ACTION pour afficher l’écran MENU. MENU DVD BLOCAGE LANGUE TELE HORLOGE CANAL 53 SEL.
Menu vidéo/audio Cette fonction permet de régler l’image et la piste sonore selon chacune des sources de programme. Menu audio Menu vidéo 1 2 Appuyer sur ACTION* pour afficher l’écran MENU. DVD BLOCAGE LANGUE TELE HORLOGE CANAL 53 SEL. : FIN 3 1) Appuyer sur pour sélectionner “TELE”. 2) Appuyer sur SET pour afficher l’écran REGLAGE TELEVISEUR. MENU 1 REGLER : SET : ACT I ON 1) Appuyer sur pour sélectionner “REGLAGE VIDEO/AUDIO”. 2) Appuyer sur SET pour afficher l’écran REGLAGE VIDEO/AUDIO.
Réglage vidéo/audio *Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche télécommande et essayer à nouveau. Réglage audio Réglage vidéo 1 2 Appuyer sur ACTION pour afficher l’écran MENU. MENU DVD BLOCAGE LANGUE TELE HORLOGE CANAL 53 SEL. : FIN 3 1 REGLER : SET : ACT I ON REGLAGE TELEV I SEUR SOUS - T I TRES SELECT SOURCE : BLC ACCORD REGLAGE V I DEO / AUD I O REGLAGE VOL. DVD : + 2 ANTENNE FM : I NT. MESSAGE D' ERREUR : OU I REGLER : SET SEL.
Utilisation du disque Langue des sous-titres (DVD seulement) Il est possible de sélectionner une langue (dans la mesure où elle est disponible) pour les sous-titres autre que celle réglée aux réglages initiaux du DVD. (Voir à la page 66.) Liste des préparatifs Lire la section “Utilisation de base du DVD” à la page 22. Appuyer sur SUB TITLE* en mode lecture pour afficher la sélection de langue des sous-titres. 1 S UR RO UND • L’affichage disparaît après 5 secondes.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche DVD de la télécommande et essayer à nouveau. Langue de la piste audio (DVD seulement) Il est possible de changer la langue de la piste audio réglée au moment des réglages initiaux du DVD si la langue choisie est disponible. (Voir à la page 66.) (Cette opération n’est possible qu’avec les disques ayant plusieurs langues enregistrées sur la piste audio.
Utilisation du disque (suite) Visionnement à angles multiples (DVD seulement) Certains disques DVD comportent des scènes enregistrées sous divers angles de prise de vue. Avec ces disques, il est possible de voir une même scène sous ces différents angles, lorsque disponibles, à l’aide de la touche ANGLE. 1 Lorsque apparaît sur l’écran lors d’une pression sur une touche, cela signifie que l’action correspondante n’est pas possible sur le disque ou sur l’appareil.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche DVD de la télécommande et essayer à nouveau. Menu de titres (DVD seulement) Il peut arriver que certains disques DVD comportent plus d’un titre (film). Si un menu des titres est disponible, il est alors possible de choisir le numéro du titre voulu. (Il est à noter que l’opération peut varier selon le disque.) Appuyer sur TITLE en mode lecture pour afficher le menu de titres.
Utilisation du disque (suite) Lecture programmée (CD-Vidéo/CD) Liste des préparatifs S’assurer que l’appareil est en mode télé-magnétoscope en appuyant sur . S’assurer qu’un disque CD-Vidéo ou CD a été mis en place. Il est possible de programmer la lecture des plages et leur ordre de lecture. 1 2 Appuyer sur ACTION en mode arrêt pour afficher le menu. MENU DVD BLOCAGE LANGUE TELE HORLOGE CANAL 53 SEL. : FIN 1 REGLER : SET : ACT I ON MODE DE LECTURE LECTURE PROGRAMMEE LECTURE ALEATOIRE SEL.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche de la télécommande et essayer à nouveau. ou DVD Lecture aléatoire (CD-Vidéo/CD) Les plages sont lues dans un ordre aléatoire. 1 MENU DVD BLOCAGE LANGUE TELE HORLOGE CANAL 53 SEL. : FIN 1 1) Appuyer sur pour sélectionner “DVD”. 2) Appuyer sur SET pour afficher. REGLER : SET S UR RO UND 2 Appuyer sur ACTION* en mode arrêt pour afficher le menu.
Opération avec disque DVD-RAM (DVD-RAM seulement) Ce combiné prend en charge les disques DVD-RAM enregistrés et édités par l’utilisateur. Nota • Aucun enregistrement sur DVD-RAM n’est possible sur ce combiné. Lecture d’un DVD-RAM 1 Suivre les étapes 1 à 2 à la page 22. 2 Appuyer sur TITLE* ou MENU pour afficher le menu du navigateur direct ou de la liste de lecture pour sélectionner facilement un titre ou une séquence.
*Important: ou DVD Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche de la télécommande et essayer à nouveau. Play List (Liste de lecture) Si le disque DVD-RAM comporte une liste de lecture, la liste de lecture des titres présélectionnés par l’utilisateur s’affiche en vue d’en faciliter l’accès. (L’opération peut varier selon le mode d’édition du DVD-RAM.) 1 2 Appuyer sur MENU en mode lecture/arrêt pour afficher la liste de lecture.
Fonctionnement du lecteur DVD à partir des affichages à l’écran Sur pression de la touche DISPLAY, des affichages donnent des informations sur le disque (titre/numéro de chapitre/plage et temps écoulé) de même que des informations sur l’état de l’appareil (lecture en reprise, mode de lecture). 1 Liste des préparatifs S’assurer que l’appareil est en mode DVD en appuyant sur DVD. Appuyer sur DISPLAY* en mode lecture ou arrêt pour activer les affichages à l’écran.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche DVD de la télécommande et essayer à nouveau. Description détaillée des écrans ■ Écran d’informations sur le disque (pour DVD) 1.N° de titre 1 2 T I TRE : 1 CHAPITRE : 12 DVD 01 : 23: 45 3 4 • Sélectionner “TITRE” et appuyer sur SET. ou au moyen des touches • Changer le numéro en appuyant sur numériques, puis appuyer sur SET. 2.N° de chapitre SEL. : REGLER: SET • Sélectionner “CHAPITRE” et appuyer sur SET.
Fonctionnement du lecteur DVD à partir des affichages à l’écran (suite) Description détaillée des écrans ■ Écran d’informations sur l’appareil • Sélectionner “REPRISE” et appuyer sur SET*. • Pour changer le mode pendant la lecture, appuyer sur , puis appuyer sur SET. a.
*Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche DVD de la télécommande et essayer à nouveau.
Lecture de fichiers MP3/WMA/JPEG Cet appareil peut prendre en charge des CD-R et des CR-RW avec fichiers au format MP3/WMA/JPEG enregistrés sur un ordinateur et destinés à un usage personnel. Il se pourrait toutefois que certains disques ne puissent être lus en raison des conditions d’enregistrement. 1 2 3 4 Racine My favorite CAR1.jpg CAR2.jpg END_WALTZ.mp3 PICTURES Appuyer sur POWER de la télécommande ou du combiné. Appuyer sur OPEN/CLOSE, puis placer un disque MP3/WMA/JPEG sur le plateau.
Lecture de fichiers MP3/WMA Suivre les étapes 1 à 3 à la page 62. mode arrêt, appuyer sur pour 1 Ensélectionner un fichier MP3/WMA ( / ) 2 Appuyer sur SET ou PLAY pour commencer la lecture. ■ Recherche avant/arrière Appuyer sur FF/SLOW+ ou sur REW/SLOW– pendant la lecture. Appuyer sur PLAY pour désactiver. • La vitesse de recherche, lente au début, augmente avec chaque pression sur la touche jusqu’à 5 pressions. ■ Saut de plage avant/arrière | ou sur SKIP- | Appuyer sur SKIP+ pendant la lecture.
Lecture de fichiers MP3/WMA/JPEG (suite) Diaporama JPEG Zoom sur images JPEG (Pendant la lecture de fichiers JPEG) Il est possible d’agrandir des parties d’une image JPEG et de sélectionner le taux d’agrandissement à l’aide de la touche ZOOM de la télécommande. Réglage du taux d’agrandissement Appuyer sur ZOOM à répétition pour modifier l’affichage comme suit. Appuyer sur STOP pour rappeler le menu MP3/WMA/JPEG.
Fonction de verrouillage du DVD *Important: Si une touche de la télécommande ne fonctionne pas, ou DVD de la appuyer sur la touche télécommande et essayer à nouveau. Il est possible de bloquer le visionnement de certains DVD non recommandables pour de jeunes auditoires. • Certains DVD sont codés pour la protection de certains publics sensibles. Si le niveau de protection autorisé est plus élevé que celui que vous avez préréglé, la lecture sera impossible.
Réglages initiaux du DVD 1 2 Appuyer sur ACTION* pour afficher le menu. MENU DVD BLOCAGE LANGUE TELE HORLOGE CANAL 53 SEL. : FIN 1 1) Appuyer sur pour sélectionner “DVD”. 2) Appuyer sur SET pour afficher. REGLER : SET : ACT I ON 1) Appuyer sur pour sélectionner une rubrique. 2) Appuyer sur SET. 3 LANGUES DU DISQUE (voir ci-dessous) Il est possible de sélectionner n’importe laquelle des langues disponibles sur le disque.
*Important: ou DVD de Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche la télécommande et essayer à nouveau. Sortie audio Sélectionner le type de signal audio numérique devant être transmis à la prise de sortie audio numérique optique de l’appareil. 1 2 3 Suivre les étapes 1 et 2 à la page 66. Réglage 1) Appuyer sur pour sélectionner “SORTIE AUDIO”. 2) Appuyer sur SET pour afficher. SORTIE AUDIO LPCM(DVD) Dolby Digital dts DRC SEL.
Réglages initiaux du DVD (suite) Arrêt sur image Cette fonction permet de réduire le sautillement d’une image fixe ou en mouvement. 1 2 *Important: Si une touche de la télécommande ne fonctionne pas, appuyer sur la touche DVD de la télécommande et essayer à nouveau. Suivre les étapes 1 et 2 à la page 66. S UR RO UND 1) Appuyer sur * pour sélectionner “ARRET SUR IMAGE”. 2) Appuyer sur SET à répétition pour sélectionner le mode. (Voir ci-dessous.
Liste des codes de langue Entrer le numéro de code voulu pour le réglage initial de “Audio”, “Sous-titres” et/ou “Menu” (voir page 66).
Guide de dépannage Vérifier les points suivants si l’appareil présente des problèmes de fonctionnement. Alimentation Solution Pas d’alimentation ... • Insérer la fiche du cordon d’alimentation bien à fond dans la prise secteur. • S’assurer que le contact est établi. Le contact est automatiquement coupé… • La mise hors contact survient automatiquement lorsque le lecteur DVD est en mode arrêt pendant 5 minutes ou qu’il n’y a pas de signal dans le mode télé. Rétablir le contact. (p.
DVD/CD-Vidéo/CD Solution La lecture ne peut être amorcée… La lecture s’amorce mais s’arrête immédiatement… L’image est distordue pendant l’avance et le recul rapides… La recherche (avant/arrière) n’est pas possible durant la lecture… La lecture ne s’amorce pas même si un titre a été sélectionné… La langue des dialogues et(ou) des sous-titres ne correspond pas à celle qui a été sélectionnée… Aucun sous-titre n’est affiché… Aucune autre langue pour les dialogues ou le sous-titrage ne peut être sélectionnée… I
Avertissements et directives Ces affichages indiquent une erreur d’opération ou donnent des instructions supplémentaires. Affichage à l’écran Explication Ce message s’affiche dans le cas où la programmation d’un REGLER L’HORLOGE enregistrement différé ou d’une mise en marche différée est tentée AVANT DE PROGRAMMER sans que l’horloge n’ait d’abord été réglée… (p.18-19) VERIFIER CASSETTE Dans le cas où la touche REC est pressée et que la languette de LANGUETTE DE protection de la cassette a été rompue… (p.
Garantie/Liste des centres de service Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 Certificat de garantie limitée Panasonic Panasonic Canada Inc. garantit cet appareil contre tout vice de fabrication et accepte, le cas échéant, de remédier à toute défectuosité pendant la période indiquée ci-dessous et commençant à partir de la date d’achat original.
Index Téléviseur / magnétoscope A B C D E F I L 74 Accessoires .......................................................... 4 Affichage des fonctions et des canaux............... 29 Affichage des sous-titres ............................... 26-27 Affichage des sous-titres avec réglage silencieux............................................................ 27 Affichages à l’écran ............................................ 29 Annulation d’un enregistrement différé............... 33 Arrêt sur image.......
Téléviseur / magnétoscope T Table des matières ............................................... 5 Télécommande multimarque .............................. 34 Touche 100 ......................................................... 24 Touche ACTION ........................................... 10, 18 Touche ADD/DLT /CLEAR ............................ 10, 19 Touche AUDIO........................................ 10, 25, 46 Touche CH , CH ....................................... 10, 24 Touche CM/ZERO ...................
LSQT0721A Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-5010 www.panasonic.ca Montréal: 3075 Louis A. Amos, Lachine, Québec H8T 1C4 (514) 633-8684 Toronto: 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 (905) 624-8447 Calgary: 6835 - 8th Street N.E.