Operating Instructions Digital Wireless Stereo Earphones Model No.
Dear customer Thank you for purchasing this product. Please read these instructions carefully before using this product, and save this manual for future use. Table of contents Before use Accessories......................................... 2 (Important) About water resistance..... 2 Part names.......................................... 3 Preparation Charging.............................................. 3 Turning the power on/off...................... 3 Connecting a Bluetooth® device..........
Part names 1 2 3 4 5 6 7 8 Right earphone 9 11 10 2 1 2 3 4 5 6 7 8 9 Right earphone USB lid Earpiece Left earphone Cord adjuster Clip Remote controller LED illumination LED indicator light* •• The number of blinks or colour notifies the status of the unit. (* hereafter referred to as “LED”) 10 Charging terminal (DC IN) •• Open the USB lid and connect the USB charging cord (supplied) to this terminal when charging.
Connecting a Bluetooth® device How to wear the earphones To establish a wireless connection, register the unit with Bluetooth® compatible devices. Check the sides (L and R), then wear the earphones from behind your neck and hook over both ears, and bend the clip to adjust. Move the cord adjuster towards the back of your head. Preparation on the Bluetooth® device •• Turn on the power, and enable the Bluetooth® feature. •• Place the device within 1 m from the unit.
■■Note Remote controlling ■■Attention You can control the Bluetooth® device using the unit. •• Depending on Bluetooth® devices, some functions below do not work, or work differently via operation of the unit. •• M-size earpieces are attached at the time of purchase. If they are not the right size, replace them with S or L-size earpieces (supplied). •• Do not bend the clip more than necessary. The clip can not be adjusted if it is damaged.
1 Connect the Bluetooth enabled phone and unit (→ P. 4) When making an outgoing call 2 When answering an incoming call ® Press on the unit and answer the call •• During an incoming call, ringtone will sound from the earphones and the LED will blink. •• (HFP only) To reject the twice incoming call, press quickly until the ringtone stops. Remote controller Make an outgoing call on the Bluetooth® enabled phone •• Also refer to the operating manual for the Bluetooth® enabled phone.
Restoring to the factory settings Maintenance When you want to delete all pairing device information, etc., you can restore the unit to the factory settings (original settings upon purchase). Charge the battery before restoring the unit. for approximately 5 seconds 1 Press and hold •• Start searching for Bluetooth® devices to connect. 2 Press and hold + and − for 5 seconds or more simultaneously while searching •• The LED will blink fast in blue. The unit will restore to the factory settings.
Safety precautions ■■Unit •• Avoid using or placing this unit near sources of heat. •• Do not listen with this unit at high volume in places where you need to hear sounds from the surrounding environment for safety, such as at railroad crossings, and construction sites. •• Do not block the ventilation of this unit with items such as cloth for long periods of time while charging or while the power is on. Declaration of Conformity (DoC) •• Keep the earpieces out of reach of children to prevent swallowing.
About Bluetooth® Specifications Panasonic bears no responsibility for data and/or information that is compromised during a wireless transmission. ■■Frequency band used This unit uses the 2.4 GHz frequency band. ■■Certification of this unit •• This unit conforms to frequency restrictions and has received certification based on frequency laws. Thus, a wireless permit is not necessary. •• The actions below are punishable by law in some countries: – Taking apart/modifying the unit.
Troubleshooting guide Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the remedies indicated do not solve the problem, consult your dealer for instructions. General The unit does not respond •• Connect the unit to a computer using the USB charging cord. The unit will be reset. (→ P. 6) Power supply and charging Cannot charge the unit •• Make sure the computer is turned on and is not on standby or sleep mode.
To remove the battery when disposing of this unit 1 2 A 4 B When disposing of this unit, take out the battery installed in this unit and recycle it. Danger A 3 The following instructions are not intended for repairing purposes but for the disposal of this unit. This unit is not restorable once disassembled. As the rechargeable battery is specifically for this product, do not use it for any other device. Do not charge the removed battery. •• Do not heat or expose to flame.
Disposal of Old Equipment and Batteries Only for European Union and countries with recycling systems These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries must not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points in accordance with your national legislation.
