Manual

Messages
The following messages or service numbers appear on the TV or unit's display when something unusual is detected during startup and use.
On the TV Page
Cannot play. oYou inserted an incompatible disc (Discs recorded in PAL video, etc.). 42, 43
Cannot display on this unit. oYou tried to play a non-compatible image. 43, 44
oConfirm "SD" on the unit's display is not blinking and re-insert the card.
No disc is inserted, oThe disc may be upside down.
Q This operation is not oSome operations are prohibited by the unit or disc. For example;
available. - r¢l_'_: During play back, reverse slow-motion or reverse frame-by-frame is not possible.
Q This operation is prohibited oDepending on the disc, you may not be able to perform search or skip when film previews
by this disc. and warning screens are being played back.
Cannot connect, oWhen a hub is used but its Link lamp does not light up, check the cable connection, LAN 14
Please check the connection of terminal connection, cable itself (a cross cable may be used by mistake), etc.
the LAN cable.
IP address is not set. 33
Cannot obtain IP address using
DHCP.
Please check the connection or
router settings.
This IP address is already in
use.
Please check the IP address
setting.
Unable to perform Connection
Test.
Please try again.
IP address not set correctly.
Connection Test was
unsuccessful. No reply
from host.
Please check the connection or
router settings.
oThe "IP Address" in "IP Address/DNS Settings" is" . . . ". Set the "IP Address",
"Subnet Mask", and "Default Gateway". (Select the automatic address acquisition if
necessary.)
olf you use a hub, then check the connection between the hub and the router.
- Use the UPLINK port of the hub to connect to a router.
-Check whether or not the hub's Link lamp lights up. If it does not light up, then check the
cable connection, LAN terminal connection, cable itself (a cross cable may be used by
mistake), etc.
• If the above conditions are OK, then the router may not operate in DHCP mode. Check the
router settings and operation. You may reset the router to restore it to normal.
• This unit's IP address is used by another device. Check the IP addresses of this unit,
personal computers, and routers, etc. If necessary, reconfigure them to avoid IP
addresses from being duplicated.
Turn the unit off. Remove the power cord and reconnect it and try again. If the same
symptom persists, then consult your dealer.
• If you use a hub, then check the connection between the hub and the router.
- Use the UPLINK port of the hub to connect to a router.
- If the hub's Link lamp does not light up, then check the cable connection, LAN terminal
connection, cable itself (a cross cable may be used by mistake), etc.
• Check the "IP Address", "Subnet Mask", and "Default Gateway" in the "IP Address/DNS
Settings".
• If the MAC address information is required, then press [SETU P] to display the "Network"
menu.
14
14
14
33
33
37
Network connection refused. •When you set "BD-Live Internet Access" to "Allow ( Limited )" and play BD-Live contents
Please confirm Setup "BD-Live which do not have a content owner certificate, the Internet access of the content is not
Internet Access." allowed. If you allow the content to connect to Internet, set "BD-Live Internet Access" to
"Allow ( ALL )'.
Unable to check for latest •The firmware download server is currently unavailable. Please try again later.
firmware version.
Please try again later.
High Clarity Sound is effective. •"High Clarity Sound" in setup menu is set to "Enable", and "High Clarity Sound" in 36, 38
Analog video output is turned on-screen menu is set to "On".
off when
playback starts.
No Video •Depending on the connected iPod, video menu may not be available on the TV. Select the 31
iPod menu (iPod LCD) mode and operate video playback from your iPod menu.
On the unit's display
F99 •The unit fails to operate properly. Press [POWER (b/I] on the main unit to switch the unit to --
standby for 3 seconds. Now press [POWER (b/I] on the main unit again to turn the unit on.
HDMI ONLY •Some BD-Video discs can only be output with HDMI. --
NET •Displays while VIERA CAST is starting up. --
No PLAY •There is a viewing restriction on a BD-Video or DVD-Video. 37
No READ •The media is dirty or badly scratched. The unit cannot play. --
PLEASE WAIT •The unit is carrying out internal process.This is not a malfunction. You cannot operate the
unit while "PLEASE WAIT" is displayed.
• When connected to TV (VIERA) with HDAVI Control 4, and power supply is turned off by
the "Auto power stand-by" function on the TV side.
SET [] •The remote control and main unit are using different codes. Change the code on the 50
(" []" stands for a number.) remote control.
Press and hold [OK] and the indicated number button at the same
time for more than 5 seconds.
UNFORMAT •You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or --
DVD-RW (DVD-Video format).
UNSUPPORT •You have inserted a media the unit cannot play. 42, 43
RQT9371