CD Stereo System Operating Instructions Model No. SC-AK100 As an E NERGY S TAR ® Partner, Panasonic has determined that this product meets the E NERGY S TAR ® guidelines for energy efficiency. Before connecting, operating or adjusting this product, please read these instructions completely. Please keep this manual for future reference. For U.S.A. only The servicenter list and warranty can be found on pages 15 and backcover.
Table of contents Dear customer Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully. Before using These operating instructions are applicable to the following system. System SC-AK100 Main unit SA-AK100 Speakers SB-AK100 CAUTION! THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
The model number and serial number of this product can be found on either the back or the bottom of the unit. Please note them in the space provided below and keep for future reference. MODEL NUMBER User memo: DATE OF PURCHASE DEALER NAME DEALER ADDRESS SERIAL NUMBER Before using TELEPHONE NUMBER IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the safety precautions listed below.
The remote control Listening caution Before using Batteries R6/LR6, AA, UM-3 Selecting fine audio equipment such as the unit you’ve just purchased is only the start of your musical enjoyment. Now it’s time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level.
Set-up Connect the AC power supply cord only after all other connections have been made. Preparation Twist and pull off the vinyl tip of the antenna wires and speaker cords. 1 FM indoor antenna Before using Adhesive tape Fix where reception is best. 4 AC power supply cord Note The included AC power supply cord is for use with this unit only. Do not use it with other equipment.
Front panel controls Main unit 1 AC supply indicator (AC IN) This indicator lights when the unit is connected to the AC power supply. 2 Standby/on switch (f f/I, POWER) Before using Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. 3 4 5 6 7 8 9 ! # $ % & ( ) Display button (DISPLAY) .......................................... 8 Display Preset EQ select button (PRESET EQ) ................... 10 Record button (a REC) ....
The radio: manual tuning The radio: preset tuning Remote control only 1 3 2 There are two methods of pre-setting stations. Automatic presetting : All the stations the tuner can receive are preset. Manual presetting : You can select the stations to preset and the order they are preset in. Up to 15 stations each can be set in the FM and AM bands. 1 Press [TUNER/BAND] to select band. The unit comes on.
CDs CD selection 2•3 1 Choose CDs with this mark: DISPLAY DEMO • • • xxxxxxx xxxxxxx x xx xx x xxx xx x xx x x xx • use irregularly shaped CDs. attach extra labels and stickers. use CDs with labels and stickers that are coming off or with adhesive exuding from under labels and stickers. attach scratch proof covers or any other kind of accessory. write anything on the CD. clean CDs with liquids. (Wipe with a soft, dry cloth.) use CDs printed with label printers available on the market.
1• 2 2• 3 1• 2 1 4 PLAY MODE Starting play from a specific track disc. 2 3 1 4 To listen to specific CDs and tracks (CD Play Mode function) Remote control only 1 Press [DISC] and (within 10 seconds) [1]–[5] to select the 2 Remote control only Preparation: Press [CD :/ J] and then [L]. To select track 10 or over, press [≥10] then the two digits. Play starts from the selected track. 1 Press [PLAY MODE] to select the desired mode.
Cassettes Enhancing the sound quality DECK 1/2 1•3 DEMO SUPER SOUND EQ PLAY MODE 2 S.SOUND EQ You can use either deck 1 or deck 2 for tape playback. Use normal position tapes. High position and metal position tapes can be played, but the unit will not be able to do full justice to the characteristics of these tapes. 1 Press [TAPE :]. You can enhance the bass and treble effect of the sound. Press [SUPER SOUND EQ]. Remote control: Press [S.SOUND EQ]. Press the button again to cancel.
Recording Optional antenna connections If the tape finishes before the CD The CD continues playing. Press [L/–DEMO] to stop it. AM outdoor antenna AM outdoor antenna (not included) To record on the other side of the tape Turn the tape over and press [a REC]. 5 -12 m (16 – 40 ft.) Reducing noise when recording AM Remote control only Hold down [PLAY MODE] while recording. Every time you hold down the button: BP1 ↔ BP2 Choose the setting with the least noise.
Auto-off function Turning the demo function off Remote control only SLEEP –AUTO OFF DEMO A demonstration of the display is shown if you have not set the clock. You can reduce the power consumed in standby mode by turning it off. During standby mode Hold down [L/–DEMO] until “NO DEMO” is displayed. Every time you hold down the button: NO DEMO (off) ↔ DEMO ON (on) To show a demonstration of the display Hold down [L/–DEMO] until “DEMO ON” is displayed.
Using the timers SLEEP – AUTO OFF 5 4 1 • 22 • 32 21 • 31 To cancel the timer Press [rPLAY/REC] to clear the timer indicator from the display. (The timer comes on at the set time everyday if the timer is on.) To change the settings (when the unit is on) To change the play/record times Do steps 1, 2, 3 and 5. To change the source or volume 1. Press [rPLAY/REC] to clear the timer indicator from the display. 2. Make changes to the source or volume. 3. Do steps 4 to 5.
Troubleshooting guide Before requesting service, make the below checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem: In the U.S.A., contact the Panasonic Customer Call Center at 1-800-211-7262, or e-mail consumerproducts@panasonic.com, or web site (http://www.panasonic.com). In Canada, contact Panasonic Canada Inc. Customer Care Centre at 905-624-5505, web site (www.panasonic.ca), or an authorized Servicentre closest to you.
Product Service 1. Damage requiring service —The unit should be serviced by qualified service personnel if: (a)The AC power supply cord or AC adaptor has been damaged; or (b)Objects or liquids have gotten into the unit; or (c)The unit has been exposed to rain; or (d)The unit does not operate normally or exhibits a marked change in performance; or (e)The unit has been dropped or the cabinet damaged. 2. Servicing —Do not attempt to service the unit beyond that described in these operating instructions.
Specifications AMPLIFIER SECTION CASSETTE DECK SECTION SPEAKER SECTION Power output 10% Total harmonic distortion 60 Hz–16 kHz, both channels driven 40 W per channel (6 Ω) Power output 10% Total harmonic distortion 1 kHz, both channels driven 50 W per channel (6 Ω) Input sensitivity AUX 250 mV Input Impedance AUX 13.