Operating Instructions

Operations
23
TQBM0479
Setup menu
1 Press [SETUP] repeatedly to select
the setup item and then press [OK].
≥ You can also press [4] or [3] repeatedly to select the
setup item.
2Press [4][3] repeatedly to select the
desired setting and then press [OK].
∫ DIMMER
Switch the brightness of the display.
≥ While “DISPLAY OFF” is set, the display lights for about
5 seconds if operations are performed on the main unit or
with the remote control.
≥ While “DISPLAY OFF” is set, a part of the display lights if
the display is off but the main unit is on.
∫ BEEP
A beep sounds when you touch the switch on the
main unit or when you turn the unit on/off.
≥ This works during muting as well.
∫ AUTO OFF
The main unit automatically is turned off if there is
no audio input and when you do not use it for
approx. 20 minutes.
≥ When this is set, the display shows “P.OFF 1MIN” to
indicate that the main unit will turn off in approximately 1
minute.
≥ If “STANDBY MODE” or “VIERA LINK” is set to “ON”, this
function will also be set to “ON”. To change the setting, set
“STANDBY MODE” and “VIERA LINK” to “OFF”. (> 23)
∫ VOL LIMITATION
When this function is set to “ON”, if the volume
exceeds 50 when the main unit is turned off, then
the volume is set to 50 when the main unit is
turned on.
∫ LINK MODE
Change the Bluetooth
®
transmission mode to
prioritise transmission quality or sound quality.
Make sure that the Bluetooth
®
device is not
connected (“BLUETOOTH READY” is indicated
on the display).
MODE 1: Emphasis on connectivity.
MODE 2: Emphasis on sound quality.
≥ The default setting is “MODE 2”.
∫ VIERA LINK
Turn on the VIERA Link function.
Select “OFF” when your HDAVI Control device
does not work correctly with this system.
≥ ARC will be disabled. Connect an optical digital audio
cable.
≥ Turn off all connected devices and then turn them on again
after changing the setting.
∫ STANDBY MODE
When this function is set to “ON”, then the main
unit automatically turns on in the following cases.
– When a Bluetooth
®
connection is established to the main
unit from a paired Bluetooth
®
device.
– When playback operations are performed on the main unit
from a device connected to the network.
≥ The default setting is “ON”.
≥ If this function is set to “ON”, the standby power
consumption will increase. (> 32)
∫ Wi-Fi
The wireless LAN function can be enabled or
disabled.
∫ Wi-Fi SIGNAL LEVEL
You can check the signal strength of the wireless
connection.
≥ The signal strength is displayed when you press [OK] while
“Wi-Fi SIGNAL LEVEL” is being displayed.
Press [OK] again to stop the display.
≥ It is recommended to have a signal strength of “LEVEL 3”.
Change the position or angle of your wireless network
router or this system if the indication is “LEVEL 2” or
“LEVEL 1” and see if the connection improves.
≥ If “LEVEL 0” is displayed, this system cannot establish a
link with the wireless network router.
≥ “WIRED LAN” is displayed when connected with a LAN
cable.
∫ NET INFO
You can confirm the IP address allocated to this
system, the MAC address of this system, and the
network name (SSID) of this system.
IP ADDRESS
SSID
MAC ADDRESS
≥ Characters that cannot be displayed are replaced with
“ ＊ ”.
∫ RESET
This restores the settings to the factory presets.
≥ For details, refer to “To return to the factory preset.” (> 26)
SC-HTB900-EGEBGN-TQBM0479_eng.book 23 ページ ２０１９年１０月１５日 火曜日 午後３時１２分