Operation Manual

RQT9478
24
Error messages
Troubleshooting and
other information
Display Check point/Cause/Countermeasure Page
CANCEL MUTE FUNCTION
(Scrolling)
• The test signal is not output while muting is on.
Cancel muting for operation.
20
MUTE (Blinking) • This is always displayed while muting is on. 20
NOT POSSIBLE FOR
THIS INPUT SOURCE
(Scrolling)
• You cannot use Dolby Virtual Speaker, SFC and Dolby Pro Logic for dual
sounds.
—
NOT POSSIBLE FOR
THIS PCM SOURCE
(Scrolling)
• You cannot use Dolby Virtual Speaker, SFC and Dolby Pro Logic effect with
PCM signals with sampling frequency of over 48 kHz.
• SFC is not available for multi-channel LPCM signal.
17
17
REMOTE 2
REMOTE 1
• Set the same remote control code for this system and remote control.
When “REMOTE 2 ” is displayed, set the code to “2 ” on the remote control
in step 4 of procedure “When other equipment (mini component system,
AV amp, etc.) manufactured by Panasonic operates with the remote control
operations of this system”. When “REMOTE 1 ” is displayed, set the code to
“1 ” on the remote control in step 4 in the same way.
23
SWITCH OFF POWER
(Scrolling)
• While “F70

” is displayed, all operations but turning ON/OFF operation
are not available.
Turn off the system, unplug the AC mains lead, and consult your dealer.
—
TURN OFF DTS FIX MODE
(Scrolling)
• When each input is fi xed to DTS (DTS FIX), the sound fi eld effects cannot be
cancelled even if you press [–SETUP, OFF]. Cancel DTS FIX.
23
U701
• The equipment connected by the HDMI cable is not compatible with this
system’s copyright protection technology.
—
U703
• A problem has occurred with the HDMI connection. Try the following to correct
the problem. Consult your dealer if the error code remains on the display.
–
Turn the connected equipment off and on again.
–
Disconnect the HDMI cable then reconnect it.
–
Do not connect more than 2 sets of equipment to this system’s output.
—
U704
• The system received incompatible video signals through HDMI connection.
Check the settings of the connected equipment.
—
Digital signals that can be played on this system
• With HDMI connection, this system can play back multi-channel LPCM signals
with sampling frequencies of over 48 kHz and PCM signals of over 96 kHz in
addition to multi-channel LPCM of up to 48 kHz and PCM of up to 96 kHz. (If
frequency exceeds these fi gures, playback equipment performs down-sampling
and plays back as 48 kHz signals. However, playback may be impossible
depending on the discs. See operating instructions of playback equipment for
more information.)
• With the digital connection, this system can play multi-channel LPCM signals
with sampling frequencies of up to 48 kHz and PCM signals of up to
96 kHz.
• See “Glossary” (
➜
page 25) for more detailed information on each signal.
 Dolby Digital
Blu-ray disc, DVD etc.
 DTS
Blu-ray disc, DVD etc.
 PCM (2-channel)
CD, DVD audio etc.
 Multi-channel LPCM (Linear PCM)
Blu-ray disc, DVD audio etc.
Error messages/Digital signals that can be played on this system/Maintenance
Note
Maintenance
Unplug the AC mains lead from the household mains socket and wipe the system using a soft and dry cloth.
• When the system is very dirty, wring the cloth soaked in water thoroughly, wipe the dirt and wipe moisture off with a
dry cloth.
• Do not use solvents such as benzine, thinner, alcohol, etc. because they may cause casing to deform and coating to
go off.
• Before using chemically treated cloth, read the instructions that come with the cloth carefully.