User manual

16
RQT7994
ConnectionsSettingsBasic OperationsOperations Before useReference
Control guide
DIGITAL EX and EX are displayed only when “1 SPKR is selected in “Surround back speaker settings”. (ápage 12)
PL
is displayed when using Dolby Pro Logic with stereo (2-channel) sources and “
SB
” is set to “
_
” in “Speakers combination settings”. (
á
page 12)
Main unit
[8, POWER]
Press to switch the unit from on to standby mode
or vice versa. In standby mode, the unit is still
consuming a small amount of power.
Standby indicator [^]
When the unit is connected to the AC mains
supply, this indicator lights up in standby mode
and goes out when the unit is turned on.
[SPEAKERS, A, B]
For selecting speakers A or B.
Turning the speakers off
automatically engages the
STEREO/2CH MIX mode (when
listening through headphones, for
example).
[MULTI CONTROL, CANCEL]
Press to enter Multi control or cancel.
[ENTER]
Enters setting in Multi control.
[INPUT SELECTOR]
For selecting input.
Selects each setting in Multi control.
[VOLUME]
Volume
control.
Remote
control signal
sensor
[VCR 2]
For a game player,
etc.
[DUAL AMP]
Lights when the
DUAL AMP function
is activated.
[BI-AMP]
Lights when the BI-
AMP function is
activated.
[BAND]
For switching between FM and AM.
[PRESET]
Press to allow preset station selection with [2 TUNE 1].
[2 TUNE 1]
For tuning the radio and selecting preset stations.
Press and hold until the frequency starts scrolling to start
automatic tuning. Tuning stops when a station is found.
[PHONES]
Headphone jack.
Plug type: 6.3 mm (1/4") stereo
Avoid listening for prolonged
periods of time to prevent hearing
damage.
Turn the speakers off when using
the headphones.
Display indicators
[RE-MASTER]
Lights when the multi-source
re-master function is on.
[MULTI CONTROL]
When you press the [MULTI
CONTROL, CANCEL] button
and enter the settings the
indicator lights.
[SLEEP]
Sleep timer indicator.
[TUNED]
A station is tuned.
[ST]
A stereo FM broadcast is tuned.
[MONO]
Lights when using the monaural
mode.
[]
Flashes during automatic
presetting.
[DIGITAL INPUT]
The channels contained in the digital input signal light.
No sound is output from a channel if the speaker is set to “
_
” (not connected) in
“Speakers combination settings” (
á
page 12) even if the channel indicator lights.
L: Front left channel C: Center channel
R: Front right channel LS: Surround left channel
SB: Surround back channel RS: Surround right channel
S: If the surround channel is monaural
LFE (Low Frequency Effects): Deep-bass effect
[PCM]
Lights when the PCM FIX mode is set.
[– SPEAKERS – , , ]
Speaker indicators.
General
display
Shows the input
mode, radio
frequency, and
other general
information.
[2CH MIX]
Lights when playing a
multi-channel source in
2CH MIX mode.
[kHz, MHz]
Frequency unit indicators.
kHz:
AM, or PCM sampling
frequency
MHz:FM
[SOUND MODE]
The following light to
indicate the source’s
input signal (multi-
channel digital signal)
and the decoding
format used.
(
á
below)
A: Sound is output from speakers connected to the
front A, surround, and center terminals.
B: Sound is output only from speakers connected to
the front B terminals.
A, B: Sound is output from speakers connected to the
front A, B, surround, and center terminals.
A, B, BI-WIRE:
Sound is output from speakers connected by Bi-wiring.
SOUND MODE
DIGITAL:
DIGITAL EX:
EX:
DTS-ES:
DTS:
DTS 96/24:
STEREO:
Dolby Digital decoder is being used.
Dolby Digital Surround EX decoder (Dolby Pro Logic decoder) is being used when
the input signal is Dolby Digital 5.1-channel or Dolby Digital Surround EX.
Dolby Digital Surround EX decoder (Dolby Pro Logic decoder) is being used when the input signal is DTS.
DTS-ES discrete or matrix decoder is being used.
DTS decoder is being used.
DTS 96/24 decoder is being used.
2-channel stereo decoder is being used.
PL :
PL :
NEO:6:
SFC:
Dolby Pro Logic
decoder is being used.
Dolby Pro Logic
decoder is being used.
DTS NEO:6 matrix
decoder is being used.
SFC matrix function is
being used.