Model No. TH-85VX200W TH-103VX200W Operating Instructions High Definition Plasma Display Contents ● ● ● ● ● ● ● ● ● ● ● Important Safety Instructions .................................. 3 Important Safety Notice .......................................... 4 Safety Precautions.................................................. 5 Accessories .......................................................... 10 Connections ...........................................................11 Power On / Off ..................
Dear Panasonic Customer Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new Plasma Display. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt also, and note down the model number and serial number of your set in the space provided on the rear cover of these instructions. Visit our Panasonic Web Site http://panasonic.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. No user-serviceable parts inside. Refer servicing to qualified service personnel. The lightning flash with arrow-head within a triangle is intended to tell the user that parts inside the product are a risk of electric shock to persons.
Important Safety Notice WARNING 1) To prevent damage which may result in fire or shock hazard, do not expose this appliance to dripping or splashing. Do not place containers with water (flower vase, cups, cosmetics, etc.) above the set. (including on shelves above, etc.) No naked flame sources, such as lighted candles, should be placed on / above the set. 2) To prevent electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personnel.
Safety Precautions WARNING Setup This Plasma Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury. (All of the following accessories are manufactured by Panasonic Corporation.) • Pedestal ......................................................................... TY-ST85P12 (for TH-85VX200W) TY-ST103PF9 (for TH-103VX200W) • Floor stand ..............................................
Safety Precautions When using the Plasma Display The Plasma Display is designed to operate on 200 - 240 V AC, 50/60 Hz. Do not cover the ventilation holes. • Doing so may cause the Plasma Display to overheat, which can cause fire or damage to the Plasma Display. Do not stick any foreign objects into the Plasma Display. • Do not insert any metal or flammable objects into the ventilations holes or drop them onto the Plasma Display, as doing so can cause fire or electric shock.
Safety Precautions CAUTION When using the Plasma Display Do not bring your hands, face or objects close to the ventilation holes of the Plasma Display. • Heated air comes out from the ventilation holes at the top of Plasma Display will be hot. Do not bring your hands or face, or objects which cannot withstand heat, close to this port, otherwise burns or deformation could result. Be sure to disconnect all cables before moving the Plasma Display.
Safety Precautions 3D Safety Precautions WARNING Small Parts 3D Eyewear contains small parts (battery and specialised band, etc.) and must be kept out of reach of small children to avoid accidental ingestion. Disassembly Do not disassemble or modify the 3D Eyewear. Lithium Battery Batteries must not be exposed to excessive heat such as sunshine, fire or the like. CAUTION To enjoy 3D images safely and comfortably, please read these instructions fully.
Safety Precautions Viewing 3D Content Content for 3D viewing includes commercially available Blu-ray discs, 3D broadcasts, etc. When preparing your own 3D content, ensure that it is properly produced. Do not use the 3D Eyewear if you have a history of over-sensitivity to light, heart problems, or have any other existing medical conditions. Please stop using the 3D Eyewear immediately, if you feel tired, are not feeling well or experience any other uncomfortable sensation.
Accessories Accessories Supply Check that you have the accessories and items shown Remote Control Transmitter N2QAYB000562 Batteries for the Remote Control Transmitter (R6 (UM3) Size × 2) Fixing band × 2 TMME203 Power supply cord TH-85VX200W Clamper × 1 TMM15412-2 Use the clamper when connecting a LAN cable. 3D Eyewear set Screwdriver These accessories will be used by professional installers when they install the unit.
Connections AC cord connection and fixing, cable fixing TH-85VX200W – AC cord fixing Unplug the AC cord Close Push until the hook clicks. 1 Plug the AC cord into Open the display unit. Plug the AC cord until it clicks. 2 Fix the AC cord with the clamper. Note: Make sure that the AC cord is locked on both the left and right sides. 2. Pull off. 1. Keep the knob pressed. – Cable fixing bands Unplug the AC cord pressing the two knobs.
Connections TH-103VX200W – AC cord fixing Unplug the AC cord Close Push until the hook clicks. 1 Plug the AC cord into Open the display unit. Plug the AC cord until it clicks. 2 Fix the AC cord with the clamper. Note: Make sure that the AC cord is locked on both the left and right sides. – Cable fixing bands 2. Pull off. 1. Keep the knob pressed. Unplug the AC cord pressing the two knobs.
Connections Video equipment connection SERIAL Control the Plasma Display by connecting to PC LAN Connect to a network to control the unit. COMPONENT/RGB IN Component/RGB Video Input Terminal 3D SHUTTER OUT Connect the 3D IR TRANSMITTER (optional accessory). PC IN PC Input Terminal Connect to video terminal of PC or equipment with Y, PB(CB) and PR(CR) output. AUDIO OUT Connect to sound equipment.
Power On / Off Connecting the AC cord plug to the Plasma Display. Fix the AC cord plug securely to the Plasma Display with the clamper. (see page 11, 12) Connecting the plug to the Wall Outlet Notes: • Main plug types vary between countries. The power plug shown at right may, therefore, not be the type fitted to your set. • When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet first. Press the Power switch on the Plasma Display to turn the set on: Power-On.
Power On / Off When first switching on the unit Following screen will be displayed when the unit is turned on for the first time. Select the items with the remote control. Unit buttons are invalid. OSD Language OSD Language 1 English (UK) Select the language. Deutsch Français 2 Set. Italiano Español ENGLISH (US) Notes: • Once the language is set, this screen won’t be displayed when switching on the unit next time. • After the setting, language selection can be done from the Setup menu.
Selecting the input signal Press to select the input signal to be played back from the equipment which has been connected to the Plasma Display. INPUT HDMI1 HDMI2 HDMI3 HDMI input terminals in HDMI 1 to HDMI 4. HDMI4 COMPONENT PC Component or RGB input terminal in COMPONENT/RGB IN.* PC input terminal in PC IN. * “COMPONENT” may be displayed as “RGB” depending on the setting of “Component/RGB-in select”.
Basic Controls Main Unit Right side surface ENTER/ Enter / Aspect button (see page 19) Up / Down button When the menu screen is displayed: “▲” : press to move the cursor up “▼” : press to move the cursor down (see page 19) MENU Infrared transmitter for 3D Eyewear Note: Do not place any objects between the transmitter and 3D Eyewear. Remote control sensor INPUT MENU Screen ON / OFF Each time the MENU button is pressed, the menu screen will switch. (see page 19) Normal Viewing Picture Sound Pos.
Basic Controls Remote Control Transmitter Standby (ON / OFF) button The Plasma Display must first be plugged into the wall outlet and turned on at the power switch (see page 14). Press this button to turn the Plasma Display On, from Standby mode. Press it again to turn the Plasma Display Off to Standby mode. PC button Press to select PC input. (see page 16) COMPO. button Press to select Component or RGB input. (see page 16) LIGHT button The remote control’s buttons illuminate.
On-Screen Menu Displays Remote Control 1 Display the menu screen. MENU Press 2 Select the menu. Picture 2 Access 1 Select Normalise Setup Picture Mode Pos./Size Contrast Sound Brightness 0 Sharpness 0 Press several times. Each time the MENU button is pressed, the menu screen will switch. Normal Viewing Picture Setup Sound Pos. /Size Monitor White balance Options Unit Warm Advanced settings Memory save Memory load The menu can be displayed directly by pressing these buttons.
Specifications TH-85VX200W Power Source Power Consumption Power on Stand-by condition Power off condition Plasma Display panel Screen size (No.of pixels) Operating condition Temperature Humidity Applicable signals Colour System Scanning format PC signals Connection terminals LAN COMPONENT/RGB IN Y/G PB/CB/B PR/CR/R AUDIO L-R PC IN TH-103VX200W 200 - 240 V AC, 50/60 Hz 1,200 W 1,450 W 0.5 W 0.5 W 0.3 W 0.
Declaration of Conformity with the requirements of Technical Regulation on the Restriction Of the use of certain Hazardous Substances in Electrical and Electronic Equipment (adopted by Order No.1057 of Cabinet of Ministers of Ukraine) The Product is in conformity with the requirements of Technical Regulation on the Restriction Of the use of certain Hazardous Substances in electrical and electronic equipment (TR on RoHS).
Memo 23
Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.