Operating instructions
FAQs, etc.
•
Technical Information
Signal name
Aspect modes
Aspect Control Signal
Widescreen signal (WSS)
Control signal through SCART
(pin 8) or HDMI terminal
Auto 16:9 14:9 Just
4:3
4:3
Full
Zoom1 Zoom2 Zoom3
TV
AV1 AV2 AV3
Component AV1 AV2
HDMI
1
HDMI
2
HDMI
3
TV/AV1/AV2/AV3
PAL
OOOOO
-
O O O OOOO
-
OO
---
PAL 525/60
OOOOO
-
OOO
---- -
OO
---
M.NTSC
OOOOO
-
OOO
---- -
OO
---
NTSC(AV input only)
OOOOO
-
OOO
---- -
OO
---
Component/HDMI
SD
525(480)/60i
OOOOO
-
OOO
---- - --
OOO
525(480)/60p
OOOOO
-
OOO
---- - --
OOO
625(576)/50i
OOOOO
-
OOO
----
O
--
OOO
625(576)/50p
OOOOO
-
OOO
----
O
--
OOO
HD
750(720)/50p
OOOOOO O O O
---- - --
OOO
750(720)/60p
OOOOOO O O O
---- - --
OOO
1125(1080)/50i
OOOOOO O O O
---- - --
OOO
1125(1080)/60i
OOOOOO O O O
---- - --
OOO
1125(1080)/50p
OOOOOO O O O
---- - --
OOO
1125(1080)/60p
OOOOOO O O O
---- - --
OOO
PC input
-
O
--
O
-------- - -----
36
37
Technical Information
Aspect Ratio
Note
•
The ratio varies depending on the programme, etc. If the ratio is greater than the standard “16:9”, black bands
may appear at the top and bottom of the screen.
•
If the screen size looks unusual when a widescreen-recorded programme is played back on a VCR, adjust the
tracking of the VCR. (See the VCR manual.)
•
Aspect mode can be memorized for SD (Standard defi nition) and HD (High defi nition) signals separately.
•
To select the ratio manually: (Only “16:9” or “4:3” in PC mode)
The optimum size and aspect can be chosen, and you can enjoy fi ner images. (p. 13)
■
Auto: Auto aspect determines the best aspect ratio to use to fi ll your screen. It does this using a four step process
to determine if the picture being viewed is a widescreen picture.
Just
14:916:9
Zoom3Zoom2Zoom1
Directly displays
the image at
“16:9” without
distortion
(anamorphic).
Displays a “16:9”
letterbox or “4:3”
image without
distortion.
Displays the image
at the standard
“14:9” without
enlargement.
Displays a
“16:9” letterbox
(anamorphic)
image full-screen
without distortion.
Displays a 4:3
image full-screen.
Stretching is only
noticeable at
the left and right
edges.
Displays a
“2.35:1” letterbox
(anamorphic)
image full-screen
without distortion.
At “16:9”, displays
the image at its
maximum (with
slight enlargement).
Auto
The best ratio is
chosen and the
picture expanded
to fi ll the screen.
If Auto aspect detects a widescreen signal it switches into the appropriate 16:9 or 14:9 widescreen mode. If Auto aspect
does not detect a widescreen signal then this advanced TV enhances the picture for optimum viewing pleasure.
The text shown on the screen indicates how Auto aspect determined which ratio to use:
“WIDE” appears in the top left of the screen if a widescreen identifi cation signal (WSS) is found or a signal found
through a SCART terminal. Auto aspect switches to the appropriate 16:9 or 14:9 widescreen ratio. This function
will also work in any aspect mode. “Auto” appears in the top left of the screen if black stripes above and below
the picture are detected. Auto aspect chooses the best ratio and expands the picture to fi ll the screen. This
process can take several minutes, depending on the darkness of the picture.
Multi Window
You can watch two images at once. (p. 13)
•
The same input mode cannot be displayed at once.
•
The sound is active for main screen only in multi window.
•
You cannot change the aspect ratio in multi window.
•
Multi window cannot be used with PC, SD card or HDMI (available for main screen only).
•
Some signals are reformatted for suitable viewing on your display.
•
The display timeout for the input mode or programme position can be adjusted by “Banner Display Timeout” in
Setup Menu (p. 21).
•
This function may not work normally depending on the equipment condition.
•
Image or sound may not be available for the fi rst few seconds when the playback starts.
•
Image or sound may not be available for the fi rst few seconds when Input mode is switched.
•
Volume function will be displayed when adjusting the volume of the equipment.
•
If you connect the equipment that has “HDAVI Control 2” function to the TV with HDMI cable, the sound from
DIGITAL AUDIO OUT terminal can be output as multi channel surround.
•
Easy playback is also available by using the remote control for Amplifi er or Player theatre. Read the manuals of
the equipment.
•
If you connect the same kind of equipment at once (for example: one DIGA to HDMI1 / another DIGA to HDMI2),
VIERA Link is available for the terminal with the smaller number.
•
“HDAVI Control 2” is the newest standard (current as of February, 2007) for Panasonic’s HDAVI Control
compatible equipment. This standard is compatible with Panasonic’s conventional HDAVI equipment.
HDMI connections to some Panasonic equipment allow you to interface them automatically. (p. 32)
VIERA Link “ Control
TM
”
4:3 Full
Displays a “4:3”
image enlarged
horizontally to fi t
the screen.
4:3
Displays the
image at the
standard “4:3”
without distortion.