Operating Instructions

ManualsBrandsPanasonic ManualsCommunication ProductsVLMV10EX2

Installation Guide

R Main monitor station is described as "main monitor" in this guide.

R In this guide, the suffix of each model number (e.g., the "EX1" in "VL-MV10EX1") is

omitted unless necessary.

Note to the installer

R Before attempting to connect or operate this product, please read the label on the rear of

the main monitor.

R Please read this guide carefully, and install the product safely and correctly by following

the instructions. Carefully read the information found in the section titled "Important

safety information" in particular.

R Only use attachments/accessories specified by the manufacturer.

R The installation shall be carried out in accordance with all applicable installation rules.

R To the maximum extent permitted by law, Panasonic assumes no responsibility for

injuries or property damage resulting from failures arising out of improper installation or

operation inconsistent with this document.

Model Name Main Monitor Station

Model No. VL-MV10

Summary of content (8 pages)

PAGE 1
Installation Guide Model Name Main Monitor Station Model No. VL-MV10 R Main monitor station is described as "main monitor" in this guide. R In this guide, the suffix of each model number (e.g., the "EX1" in "VL-MV10EX1") is omitted unless necessary. Note to the installer R Before attempting to connect or operate this product, please read the label on the rear of the main monitor. R Please read this guide carefully, and install the product safely and correctly by following the instructions.
PAGE 2
Important safety information To prevent severe injury or loss of life or property, and to ensure proper and safe operation of your product, read this section carefully before using the product. WARNING Preventing fire, electric shock and short circuits R Leave installation work to the dealer. Installation work requires technical knowledge and experience. Electrical connection work should be performed by certified personnel only.
PAGE 3
Supplied accessories for installation For the main monitor Screw ´ 2 (4 mm ´ 16 mm) Mounting bracket ´ 1 Important: R You will need the following additional items to install and configure the main monitor. [Locally procured] – Wires: Prepare wires of the appropriate specification. (a"Wire type and length") Note: R The illustrations in the supplied manual(s) may vary slightly from the actual product.
PAGE 4
Precautions for installation R This product is a bus-powered main monitor for use with Panasonic Video Intercom Systems. Power is supplied from a lobby station or distributor. R Do not install the product in the following locations. There may be a risk of malfunction or communication disturbances. – Places where vibration, impact, or echoing occurs. – Places near a high concentration of dust, hydrogen sulphide, ammonia, sulphur, or noxious fumes.
PAGE 5
Wire type and length Wire type*1 Wiring run Diameter Max. length ø 0.65 mm (22 AWG) approx. 100 m ø 1.2 mm (17 AWG) approx. 200 m Door bell*2 ø 0.5 mm - ø 1.2 mm (24 AWG - 17 AWG) According to specification of connected device. Connection device for option output (A contact)*3 ø 0.5 mm - ø 1.2 mm (24 AWG - 17 AWG) According to specification of connected device.
PAGE 6
Main monitor installation position Installing the main monitor 1 About the installation position of the main monitor and mounting bracket R Place the main monitor in a location that your eyes are the same height as the centre of the display.
PAGE 7
Important: R Do not connect the power cable. (Damage may occur.) 3 Mount the main monitor to the mounting bracket. 3-1 Line up the tab on the bottom of the bracket with the groove on the main monitor. 3-2 Line up the tab on the top of the bracket with the groove on the main monitor, and push the main monitor down until it is secure.
PAGE 8
1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8501, Japan http://www.panasonic.