Installation Guide Video Intercom System — Power Supply Unit Model No. VL-PS240 Thank you for purchasing a Panasonic product. Please follow all instructions in this document and save it for future reference. Carefully read the information found in the section titled "1.1 Important safety information" in particular. This product is a separately sold power supply unit for use with Panasonic Video Intercom Systems.
Table of Contents 1. Important Information 1.1 1.2 1.3 1.4 1.5 1.6 1.7 Important safety information ..........................3 Important safety instructions .........................4 Disclaimer .....................................................4 Other important information ..........................4 General information .......................................4 For India only ................................................5 For Europe ....................................................5 2.
1. . Important Information 1. Important Information 1.1 Important safety information To prevent severe injury or loss of life or property, and to ensure proper and safe operation of your product, read this section carefully before using the product. WARNING Preventing fire, electric shock and short circuits R Leave installation work to the dealer. Installation work requires technical knowledge and experience. Electrical connection work should be performed by certified personnel only.
1. Important Information 1.2 Important safety instructions When using this product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, or personal injury. 1. Do not use this product near water. For example, near a bathtub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. 2. Use only the power supply unit indicated in this document.
1. Important Information Disposal of Old Equipment (Only for European Union and countries with recycling systems) Disposal information A This symbol (A) on the products, packaging, and/or accompanying documents means that used electrical and electronic products must not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points in accordance with your national legislation.
2. . Preparation 2. Preparation 2.1 Included items 2.3 Device diagrams The following items are included in addition to the power supply unit. Example: power supply unit with the cable cover removed Item Quantity Screw (4 mm ´ 40 mm) Used to secure the power supply unit to the wall. 2 A C B Cable binder Used to secure the AC and DC wires. 2 A Hook for tying cables to with a cable binder B AC IN connection terminals C DC OUT connection terminals 2.
3. . Installation 3. Installation 3.1 Installation cautions Refer to the information found in 1 Important Information (Page 3) before installing the product. CAUTION R Always connect power cables to the appropriate connection terminals. Incorrectly connecting the power cables may damage the power supply unit. R To prevent the power cables from disconnecting and to prevent electric shock, secure the power cables using the included cable binders and attach the cable covers.
3. Installation wire should be connected to, and insert the DC wires as shown. 3.2.1 Connecting the AC wires and DC wires 1 Strip the ends of the wires that connect to the power supply unit as shown below. CAUTION AC wires DC wires 45 mm 25 mm 7 mm 4 7 mm 2 Remove the cable cover screws and then remove the cable covers. R Insert the power cables firmly all the way into the terminals. If the cables are not inserted all the way, heat may be generated.
3. Installation 3.2.2 Mounting on a DIN rail Attach the power supply unit to the DIN rail so that the bottom hook is positioned at the bottom of the power supply unit. 1 Hang the top hooks (A) of the power supply unit on the top of the DIN rail. R At this point the power supply unit will be hanging from the DIN rail but will not be secure. 2 Pull the lever (B) down, make sure the bottom of the power supply unit is flat against the DIN rail, and then release to lever.
3. Installation 3.3 Cleaning Wipe the product with a soft, dry cloth. For excessive dirt, wipe the product with a slightly damp cloth. Important: R Do not use any cleaning products that contain alcohol, polish powder, powder soap, benzine, thinner, wax, petroleum, or boiling water. Also do not spray the product with insecticide, glass cleaner, or hair spray. This may cause a change in colour or quality of the product. 3.4 Terms and illustrations in this document R Model number suffixes (e.g.
Notes 11
1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8501, Japan http://www.panasonic.
