Hybrid IP-PBX Installation Manual Model KX-TDA100 KX-TDA200 Thank you for purchasing a Panasonic Hybrid IP-PBX. Please read this manual carefully before using this product and save this manual for future use. KX-TDA100/KX-TDA200: PMPR Software File Version 3.0000 or later SD Logo is a trademark.
System Components System Components Table Category Shelves Model No.
System Components Table Category Model No. Description Optional SD Memory Card KX-TDA0920 SD Memory Card for Software Upgrade to Enhanced Version Power Supply Units (PSUs) KX-TDA0103 L-Type Power Supply Unit (PSU-L) KX-TDA0104 M-Type Power Supply Unit (PSU-M) KX-TDA0108 S-Type Power Supply Unit (PSU-S) Cell Stations (CSs) KX-TDA0142 3-Channel Cell Station Unit Using CSIF Card for 2.4 GHz Portable Station KX-T0141 2-Channel Cell Station Unit Using DHLC/DLC Card (PT-interface CS) for 2.
Important Notice Prior to connection of this product, please verify that the intended operating environment is supported.
Important Safety Instructions SAFETY REQUIREMENTS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug the product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Clean with a damp cloth. 4.
SAVE THESE INSTRUCTIONS 6 Installation Manual
Precaution WARNING DO NOT REMOVE SD MEMORY CARD WHILE POWER IS SUPPLIED TO THE HYBRID.IP-PBX Doing so may cause the Hybrid IP-PBX to fail to start when you try to restart the system.
• • • Keep the unit away from heating appliances and devices that generate electrical noise such as fluorescent lamps, motors and televisions. These noise sources can interfere with the performance of the Hybrid IP-PBX. This unit should be kept free of dust, moisture, high temperature (more than 40 °C [104 °F]) and vibration, and should not be exposed to direct sunlight. If you are having problems making calls to outside destinations, follow this procedure to test the CO lines: 1.
Password Security Warning to the Administrator or Installer regarding the system password 1. Please provide all system passwords to the customer. 2. To avoid unauthorized access and possible abuse of the PBX, keep the passwords secret, and inform the customer of the importance of the passwords, and the possible dangers if they become known to others. 3. The PBX has default passwords preset. For security, change these passwords the first time that you program the PBX. 4. Change the passwords periodically.
When you ship the product Carefully pack and send it prepaid, adequately insured and preferably in the original carton. Attach a postage-paid letter, detailing the symptom, to the outside of the carton. DO NOT send the product to the Executive or Regional Sales offices. They are NOT equipped to make repairs. Product Service Panasonic Factory Servicenters for this product are listed in the servicenter directory. Consult your certified Panasonic dealer for detailed instructions.
Introduction This Installation Manual is designed to serve as an overall technical reference for the Panasonic Hybrid IPPBX, KX-TDA100/KX-TDA200. It provides instructions for installing the hardware, and programming the Hybrid IP-PBX using the KX-TDA Maintenance Console. The Structure of this Manual This manual contains the following sections: Section 1 System Outline Provides general information on the Hybrid IP-PBX, including the system capacity and specifications.
F.C.C. REQUIREMENTS AND RELEVANT INFORMATION 1. Notification to the Telephone Company This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the side of this equipment is a label that contains, among other information, a product identifier in the format US: ACJMF03AKX-TDA100. If requested, this number must be provided to the telephone company. Installation must be performed by a qualified professional installer.
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
For Cell Station CAUTION Any changes or modifications not expressly approved by the party responsible for compliance could void user's authority to operate this device. Note This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Table of Contents 1 System Outline ..................................................................................... 19 1.1 1.1.1 1.2 1.2.1 1.2.2 1.3 1.3.1 1.4 1.4.1 1.4.2 1.4.3 2 System Highlights .......................................................................................................... 20 System Highlights ............................................................................................................. 20 Basic System Construction .......................................
2.5.5 2.5.6 2.5.7 2.5.8 2.6 2.6.1 2.6.2 2.6.3 2.6.4 2.6.5 2.6.6 2.7 2.7.1 2.7.2 2.7.3 2.7.4 2.8 2.8.1 2.8.2 2.8.3 2.8.4 2.8.5 2.8.6 2.8.7 2.8.8 2.9 2.9.1 2.10 2.10.1 2.11 2.11.1 2.12 2.12.1 3 Guide for the KX-TDA Maintenance Console ................................... 157 3.1 3.1.1 3.2 3.2.1 3.3 3.3.1 4 16 Overview ........................................................................................................................158 Overview ........................................................
5.1 5.1.1 5.1.2 5.1.3 Revision History............................................................................................................ 186 PMPR Software File Version 1.1xxx ............................................................................... 186 PMPR Software File Version 2.0xxx ............................................................................... 187 PMPR Software File Version 3.0xxx ...............................................................................
Installation Manual
Section 1 System Outline This section provides general information on the Hybrid IPPBX, including the system capacity and specifications.
1.1 System Highlights 1.1 System Highlights 1.1.1 System Highlights Networking Features The Hybrid IP-PBX supports the following private networking features: TIE Line Service PBXs can be connected via privately leased telephone lines forming a private network. These "TIE lines" provide a cost-effective way to route calls and communications, and are often used to connect corporate offices located in different cities.
1.1 System Highlights Third-Party CTI Applications The Hybrid IP-PBX supports industry standard protocols, allowing third-party CTI applications to be integrated with the PBX and its extensions. Voice Mail Features A Voice Processing System (VPS) can be connected to the Hybrid IP-PBX to provide Voice Mail (VM) and Automated Attendant (AA) services. A Panasonic VPS which supports DPT (Digital) Integration can be connected to the Hybrid IP-PBX effortlessly and with minimal setup required.
1.2 Basic System Construction 1.2 Basic System Construction 1.2.1 Basic Shelf The basic shelf contains an MPR card for controlling the Hybrid IP-PBX. To use the system, install a power supply unit (PSU) in the PSU Slot and optional service cards in the basic shelf.
1.2 Basic System Construction 1.2.
1.
1.3 Optional Equipment 1.3 Optional Equipment 1.3.1 Optional Equipment Model No. Model Name Description KX-TDA0103 L-Type Power Supply Unit (PSU-L) Power Supply Unit for KX-TDA200. Total power output of 279 W. Safety Class 1 compliant. KX-TDA0104 M-Type Power Supply Unit (PSU-M) Power Supply Unit for KX-TDA100 and KX-TDA200. Total power output of 140.4 W. Safety Class 1 compliant.
1.3 Optional Equipment Model No. Model Name Description KX-TDA0181 16-Port Analog Trunk Card (LCOT16) 16-port analog CO line card with 4 power failure transfer (PFT) ports. KX-TDA0187 T-1 Trunk Card (T1) 1-port T1 CO line card. EIA/TIA standard compliant. KX-TDA0190 Optional 3-Slot Base Card (OPB3) Optional 3-slot base card for mounting a maximum of 3 optional service cards from the following: MSG4, DPH4, or ECHO16 card. KX-TDA0191 4-Channel Message Card (MSG4) 4-channel message card.
1.4 Specifications 1.4 Specifications 1.4.1 General Description Control Bus Original bus (16-bit, 8 MHz, 10 megabytes per second) Communication Bus H.100 bus conformity (1024 time slots) Switching Non-blocking Power Input PSU-S 100 V AC to 130 V AC, 1.4 A/200 V AC to 240 V AC, 0.8 A, 50 Hz/60 Hz PSU-M 100 V AC to 130 V AC, 2.5 A/200 V AC to 240 V AC, 1.4 A, 50 Hz/60 Hz PSU-L 100 V AC to 130 V AC, 5.1 A/200 V AC to 240 V AC, 2.
1.4 Specifications Extension Connection Cable Dimension Weight (when fully mounted) *1 28 SLT 1-pair wire (T, R) DPT 1-pair wire (D1, D2) or 2-pair wire (T, R, D1, D2) APT 2-pair wire (T, R, D1, D2) PT-interface CS 1-pair wire (D1, D2) DSS Console and Add-on Key Module 1-pair wire (D1, D2) KX-TDA100 334 mm (W) × 390 mm (H) × 270 mm (D) (13-1/3 in × 15-3/5 in × 10-4/5 in) KX-TDA200 430 mm (W) × 415 mm (H) × 270 mm (D) (17-1/5 in × 16-3/5 in × 10-4/5 in) KX-TDA100 Under 12 kg (26.
1.4 Specifications 1.4.
1.4 Specifications 1.4.3 System Capacity Maximum Optional Service Cards There are 2 types of optional service cards for installation: • Cards installed in the slots of the Hybrid IP-PBX • Cards mounted on other optional service cards Notes • • Any card that exceeds the capacity of the Hybrid IP-PBX will be ignored. When the Hybrid IP-PBX starts up with an invalid configuration, some cards will be ignored. Cards Installed in the Slots of the Hybrid IP-PBX KX-TDA100 KX-TDA200 A B A.
1.4 Specifications The following number of optional service cards can be installed in the various slots of the Hybrid IP-PBX.
1.4 Specifications Cards Mounted on Other Optional Service Cards The following number of optional service cards can be mounted on the specified other optional service cards. Maximum Number Card Type Mounted on KX-TDA100 KX-TDA200 MEC 1 1 RMT 1 1 CID8 12 16 LCOT8 Card/LCOT16 Card EXT-CID 6 8 SLC8 Card DPH4 4 4 2*1 2*1 MSG4 4 4 EIO4 4 4 MPR Card ECHO16 *1 OPB3 Card Only 1 ECHO16 card can be mounted on each OPB3 card.
1.4 Specifications MEC Card Calculation Calculate the MEC figure from the type and total number of items of equipment to be connected. If the MEC figure exceeds 64 (for KX-TDA100) or 128 (for KX-TDA200), you need to install an MEC card.
1.4 Specifications Power Supply Unit Selection Hybrid IP-PBX needs a power supply unit (PSU) suitable for its configuration. Calculate the load figure from the type and number of items of equipment to be connected, and determine the type of PSU that will be required.
1.4 Specifications Calculation Example (KX-TDA200) Equipment Type Load Figure KX-T7600 series DPT 48 units 48 Other DPT 2 units 8 SLC16 1 card 16 MSLC16 1 card 16 VPS 8 ports 8 Total 96 The total load figure is 96. As this is between 64 and 128, you should install the PSU-M. However, if you expect expansion in the future, it may be better to install the PSU-L. There is no harm in installing a PSU that is larger than is required for the current configuration.
1.
Section 2 Installation This section describes the procedures to install the Hybrid IPPBX. Detailed instructions for planning the installation site, installing the shelves and optional service cards, and cabling of peripheral equipment are provided. Further information on system expansion and peripheral equipment installation is included.
2.1 Before Installation 2.1 Before Installation 2.1.1 Before Installation Please read the following notes concerning installation and connection before installing the Hybrid IP-PBX and terminal equipment. Be sure to comply with all applicable laws, regulations, and guidelines. Safety Installation Instructions When installing telephone wiring, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1.
2.1 Before Installation 3. Avoid using the same AC outlet for computers, telexes, and other office equipment, as noise generated by such equipment may hamper system performance or interrupt the system. 4. Use 2-pair telephone cables when connecting PTs. Use 1-pair telephone cables when connecting SLTs, data terminals, answering machines, computers, Voice Processing Systems, etc. 5. Unplug the system from its power source when wiring, and plug the system back in only after all wiring is completed. 6.
2.2 Installation of the Hybrid IP-PBX 2.2 Installation of the Hybrid IP-PBX 2.2.
2.2 Installation of the Hybrid IP-PBX 2.2.2 Names and Locations Inside View KX-TDA100 KX-TDA200 D D C C B A E F A. B. C. D. E. F. G. H. I.
2.2 Installation of the Hybrid IP-PBX 2.2.3 Opening/Closing the Front Cover Opening the Front Cover 1. Insert a flathead screwdriver into the opening (on the left of the screw cover) and unlatch the screw cover. Screw Cover 2. Turn the screw counterclockwise to loosen. 3. Slide the front cover to the right until it stops, then lift the front cover.
2.2 Installation of the Hybrid IP-PBX Closing the Front Cover 1. Hook the front cover onto the shelf (line up the protrusions on the cover with the receptacles on the shelf). Then slide the front cover to the left until it locks. 2. Turn the screw clockwise to tighten. 3. Secure the screw cover. 2 1 Notes • • For safety reasons, close the front cover and tighten the screw before operating the Hybrid IP-PBX. Do not forget to tighten the screw before securing the screw cover.
2.2 Installation of the Hybrid IP-PBX 2.2.4 Installing/Replacing the Power Supply Unit Function PSU Type Lower/Upper Input Voltage Range Current PSU-S (for KX-TDA100) Lower: 100 V AC to 130 V AC 1.4 A Upper: 200 V AC to 240 V AC 0.8 A PSU-M (for KX-TDA100/200) Lower: 100 V AC to 130 V AC 2.5 A Upper: 200 V AC to 240 V AC 1.4 A PSU-L (for KX-TDA200) Lower: 100 V AC to 130 V AC 5.1 A Upper: 200 V AC to 240 V AC 2.
2.2 Installation of the Hybrid IP-PBX 4. To protect the back board from static electricity, do not touch parts on the back board in the main unit and PSU. To discharge static electricity, touch ground or wear a grounding strap. The following procedures are for installing or replacing a PSU only. Do not replace or remove the PSU for any other purpose. Installing the Power Supply Unit 1. Insert the PSU along the guide rails. CAUTION For safety reasons, do not touch parts in the PSU. Guide Rail 2.
2.2 Installation of the Hybrid IP-PBX 3. Turn the 4 screws clockwise, in the order indicated by the numbers 1 to 4, to fix the PSU. 3 2 Screws 4 1 Replacing the Power Supply Unit 1. Unplug the AC power cord. 2. Turn the 4 screws counterclockwise to loosen them.
2.2 Installation of the Hybrid IP-PBX 3. Pull the release lever in the direction of the arrow to disconnect the PSU from the back board. Back Board Release Lever 4. Replace the PSU. New PSU Current PSU 5. Follow the steps in "Installing the Power Supply Unit".
2.2 Installation of the Hybrid IP-PBX 2.2.5 Frame Ground Connection IMPORTANT Connect the frame of the Hybrid IP-PBX to ground. 1. Loosen the screw. 2. Insert a grounding wire (user- Screw supplied)*. 3. Tighten the screw. 4. Connect the grounding wire to ground. Grounding wire To Ground * For grounding wire, green-and-yellow insulation is required, and the cross-sectional area of the conductor must be more than 0.75 mm2 or 18 AWG. • • • Be sure to comply with applicable local regulations (e.g.
2.2 Installation of the Hybrid IP-PBX 2.2.6 Installing/Removing the Optional Service Cards CAUTION To protect the back board from static electricity, do not touch parts on the back board in the main unit and on the optional service cards. To discharge static electricity, touch ground or wear a grounding strap. Note The optional service cards can be installed or removed while the DC power is supplied. However, when installing or removing the MPR card, the DC power supply must be turned off.
2.2 Installation of the Hybrid IP-PBX 2. Holding the card as shown below, push the release lever in the direction of the arrow so that the card engages securely with the connector on the back board. Back Board Release Lever 3. Turn the 2 screws clockwise to fix the card in place. Screws Note Make sure the screws are tightened to ground the card securely.
2.2 Installation of the Hybrid IP-PBX Covering the Blank Slots Be sure to cover each slot in which no optional service card is installed by using a Blank Slot Cover. CAUTION Failure to install the Blank Slot Cover may cause electromagnetic interference.
2.2 Installation of the Hybrid IP-PBX Handling of the Cables When cables are connected to the Hybrid IP-PBX, run the cables to either the right or the left and then towards the back of the shelf as shown below. 1 2 4 3 Note For safety reasons, do not stretch, bend, or pinch the AC power cord.
2.2 Installation of the Hybrid IP-PBX Removing the Optional Service Cards 1. Turn the 2 screws counterclockwise to loosen them. Screws 2. Pull the release lever in the direction of the arrow to disconnect the card from the back board. Pull the card from the shelf to remove it.
2.2 Installation of the Hybrid IP-PBX 2.2.
2.
2.2 Installation of the Hybrid IP-PBX 2.2.8 Attaching a Ferrite Core A ferrite core must be attached when: • connecting IP-GW16 and IP-EXT16 cards using an RJ45 connector, or • connecting extension cards using an Amphenol connector. The ferrite core is included with the card. When connecting an IP-GW16/IP-EXT16 card Wrap the cable once around the ferrite core, then close the case of the ferrite core. Attach the ferrite core 5 cm (1-15/16 in) away from the connector.
2.2 Installation of the Hybrid IP-PBX If you need to open the ferrite core, use a flathead screwdriver to unlatch the case of the ferrite core.
2.2 Installation of the Hybrid IP-PBX 2.2.9 Fastening Amphenol Connector An Amphenol 57JE-type connector is used on some of the optional service cards. To connect an Amphenol connector, use the spring latch or screw to fix the upper part and use Velcro® tape to fix the lower part of the connector. Type A (Spring Latch + Velcro Tape) Type B (Screw + Velcro Tape) Velcro Tape Velcro Tape 1 Spring Latch Remove the screw on the optional service card.
2.2 Installation of the Hybrid IP-PBX Amphenol Connector Pin Assignment Chart Below is an Amphenol connector pin assignment chart for all optional service cards that use the Amphenol connector. For more details, refer to the appropriate section in "2.4 Information about the CO Line Cards" and "2.5 Information about the Extension Cards". Pin No.
2.2 Installation of the Hybrid IP-PBX 2.2.10 Wall Mounting (KX-TDA200) CAUTION • • Notes • • • • Make sure that the wall the shelf will be attached to is capable of supporting at least 4 times the weight of the shelf. Drive mounting screws into the wall. Be careful to avoid touching any metal laths, wire laths or metal plates in the wall. Do not block the openings of the shelf. Allow space of at least 20 cm (8 in) above and 10 cm (4 in) at the sides of the shelf.
2.2 Installation of the Hybrid IP-PBX 2. Hook the shelf onto the metal bracket, making sure that the shelf slides down and onto the hooked parts of the metal bracket. Use 2 screws (B) to fix both sides of the shelf.
2.2 Installation of the Hybrid IP-PBX 2.2.11 Wall Mounting (KX-TDA100) CAUTION • • Notes • • • • Make sure that the wall the shelf will be attached to is capable of supporting at least 4 times the weight of the shelf. Drive mounting screws into the wall. Be careful to avoid touching any metal laths, wire laths or metal plates in the wall. Do not block the openings of the shelf. Allow space of at least 20 cm (8 in) above and 10 cm (4 in) at the sides of the shelf.
2.2 Installation of the Hybrid IP-PBX 2. Hook the shelf onto the metal bracket, making sure that the shelf slides down and onto the hooked parts of the metal bracket. Use 2 screws (B) to fix both sides of the shelf.
2.2 Installation of the Hybrid IP-PBX 2.2.12 Floor Standing (KX-TDA200 Only) Notes • • • • Do not block the openings of the shelf. Allow space of at least 20 cm (8 in) above and 10 cm (4 in) at the sides of the shelf. Make sure that the surface behind the shelf is flat and free of obstacles, so that the openings on the back of the shelf will not be blocked. Make sure that the surface behind the shelf is not made of wood. Be careful not to drop the shelf. 1.
2.2 Installation of the Hybrid IP-PBX 3. Lift the shelf, attach it to the metal bracket, slide it backwards until it locks, and retain it with 2 screws (B). 2 1 TOP FRONT Screws (B) Metal Bracket 4. Fix the front cover on the shelf (refer to "2.2.3 Opening/Closing the Front Cover").
2.2 Installation of the Hybrid IP-PBX 2.2.13 Surge Protector Installation Overview A massive electrical surge can be caused if lightning strikes a telephone cable 10 m (33 ft) above ground, or if a telephone line comes into contact with a power line. A surge protector is a device that is connected to a CO line to prevent potentially dangerous electrical surges from entering the building via the CO line and damaging the Hybrid IP-PBX and connected equipment.
2.2 Installation of the Hybrid IP-PBX Outside Installation (Main Building) Surge Protector CO Line (Another Building) CO Line Extn. Terminal Board Extn. Surge Protector CS Extn. Extn. SLT Hybrid IP-PBX SLT PT PT CS Ground Extn.: Extension Line If you install an extension outside of the building, the following precautions are recommended: a. Install the extension wire underground. b. Use a conduit to protect the wire.
2.2 Installation of the Hybrid IP-PBX 1. Connect the grounding rod to the surge protector using a grounding wire with a cross-sectional area of at least 1.3 mm2. 2. Bury the grounding rod near the protector. The grounding wire should be as short as possible. 3. The grounding wire should run straight to the grounding rod. Do not run the wire around other objects. 4. Bury the grounding rod at least 50 cm (20 in) underground. Notes • • 68 The above figures are recommendations only.
2.3 Information about the Main Processing Card 2.3 Information about the Main Processing Card 2.3.1 MPR Card Function Contains the main processor for all processes, basic shelf main protocol, time switch (TSW) control, detection of system clock alarm, basic shelf power down alarm, and watchdog timer overflow. An MEC card and an RMT card can be mounted on the MPR card (refer to "2.3.2 MEC Card (KX-TDA0105)" and "2.3.3 RMT Card (KX-TDA0196)").
2.3 Information about the Main Processing Card • A LITHIUM BATTERY IS USED IN THE MPR CARD. THERE IS A RISK OF EXPLOSION IF THE BATTERY IS REPLACED WITH THE INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
2.3 Information about the Main Processing Card 2.3.2 MEC Card (KX-TDA0105) Function Memory expansion card to increase system data storage space and double the number of DPTs, using Digital XDP connection. To be mounted on the MPR card.
2.3 Information about the Main Processing Card 2.3.3 RMT Card (KX-TDA0196) Function Analog modem card for remote communication with the Hybrid IP-PBX. ITU-T V.90 support. To be mounted on the MPR card.
2.4 Information about the CO Line Cards 2.4 Information about the CO Line Cards 2.4.1 LCOT8 Card (KX-TDA0180) and LCOT16 Card (KXTDA0181) Function LCOT8: 8-port analog CO line card with 2 power failure transfer (PFT) ports. One CID8 card can be mounted on the LCOT8 card (refer to "2.4.2 CID8 Card (KX-TDA0193)"). LCOT16: 16-port analog CO line card with 4 power failure transfer (PFT) ports. A maximum of 2 CID8 cards can be mounted on the LCOT16 card (refer to "2.4.2 CID8 Card (KX-TDA0193)").
2.4 Information about the CO Line Cards Pin Assignments Amphenol Connector 50 26 25 1 No. Signal Name Function No.
2.4 Information about the CO Line Cards 2.4.2 CID8 Card (KX-TDA0193) Function 8-port Caller ID signal type FSK/FSK (with Call Waiting Caller ID [Visual Caller ID])/DTMF. To be mounted on the LCOT8/LCOT16 cards. inside CID8 Card Screw Accessories and User-supplied Items Accessories (included): Screws × 2 User-supplied (not included): none Note Only 1 CID8 card can be mounted on the LCOT8 card.
2.4 Information about the CO Line Cards 2.4.3 T1 Card (KX-TDA0187) Function 1-port T1 CO line card. EIA/TIA standard compliant. A LEDs B RJ45 To NT1 Accessories and User-supplied Items Accessories (included): none User-supplied (not included): RJ45 connector Notes • • • Connect this optional service card to the CO line through NT1; do not connect to the CO line directly. T1 Card must be installed behind an FCC registered and UL or CSA-NRTL listed CSU.
2.4 Information about the CO Line Cards Pin Assignments RJ45 Connector 8 1 No.
2.4 Information about the CO Line Cards 2.4.4 PRI23 Card (KX-TDA0290) Function 1-port ISDN Primary Rate Interface card (23B channels). NI (North American standard ISDN protocol) compliant. A LEDs B RJ45 NT1 Accessories and User-supplied Items Accessories (included): none User-supplied (not included): RJ45 connector Notes • • Connect this optional service card to the CO line through an NT1; do not connect to the U interface of the CO line directly.
2.4 Information about the CO Line Cards Pin Assignments RJ45 Connector 8 1 No.
2.4 Information about the CO Line Cards 2.4.5 IP-GW4 Card (KX-TDA0480) Function 4-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, and G.723.1 CODEC methods. G3 fax support.
2.
2.4 Information about the CO Line Cards 2.4.6 IP-GW4E Card (KX-TDA0484) Function 4-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, G.723.1, and G.711 CODEC methods.
2.
2.4 Information about the CO Line Cards 2.4.7 IP-GW16 Card (KX-TDA0490) Function 16-channel VoIP gateway card. Compliant with VoIP H.323 V.2 protocol, and ITU-T G.729a, G.723.1, and G.711 CODEC methods.
2.
2.5 Information about the Extension Cards 2.5 Information about the Extension Cards 2.5.1 CSIF4 Card (KX-TDA0143) and CSIF8 Card (KX-TDA0144) Function CSIF4: 4-port CS interface card for 4 CSs. CSIF8: 8-port CS interface card for 8 CSs. LED RJ45 (LINE 1 to LINE 8) To CS Accessories and User-supplied Items Accessories (included): none User-supplied (not included): RJ45 connector Notes • • • 86 LINE 5 to LINE 8 are for CSIF8 card only.
2.5 Information about the Extension Cards Editing the CS Name using the KX-TDA Maintenance Console While programming the Hybrid IP-PBX, we strongly recommend that you input a unique recognizable CS name (maximum 20 characters) for each CS port in use, and "(Reserved)" or "(Not for CSIF4)" for unused ports or unavailable ports respectively for the following reasons: a. you will be able to easily distinguish installed CSs. b. you will be able to know which CSIF card has been installed; CSIF4 or CSIF8.
2.
2.5 Information about the Extension Cards 2.5.2 DHLC8 Card (KX-TDA0170) Function 8-port digital hybrid extension card for DPTs, APTs, SLTs, DSS consoles, and PT-interface CSs, with 2 power failure transfer (PFT) ports. LED Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws × 2, Ferrite core × 1 User-supplied (not included): Amphenol connector Notes • • • Attach the included ferrite core to the cable. Refer to "2.2.8 Attaching a Ferrite Core".
2.5 Information about the Extension Cards Pin Assignments Amphenol Connector 50 26 25 1 No. Signal Name Function No.
2.
2.5 Information about the Extension Cards 2.5.3 DLC8 Card (KX-TDA0171) Function 8-port digital extension card for DPTs, DSS consoles, and PT-interface CSs. LED Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws × 2, Ferrite core × 1 User-supplied (not included): Amphenol connector Notes • • 92 Attach the included ferrite core to the cable. Refer to "2.2.8 Attaching a Ferrite Core". To connect the Amphenol connector, refer to "2.2.
2.5 Information about the Extension Cards Pin Assignments Amphenol Connector 50 26 25 1 No. Signal Name Function No.
2.5 Information about the Extension Cards 2.5.4 DLC16 Card (KX-TDA0172) Function 16-port digital extension card for DPTs, DSS consoles, and PT-interface CSs. LED Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws × 2, Ferrite core × 1 User-supplied (not included): Amphenol connector Notes • • 94 Attach the included ferrite core to the cable. Refer to "2.2.8 Attaching a Ferrite Core". To connect the Amphenol connector, refer to "2.2.
2.5 Information about the Extension Cards Pin Assignments Amphenol Connector 50 26 25 1 No. Signal Name Function No.
2.5 Information about the Extension Cards 2.5.5 SLC8 Card (KX-TDA0173) Function 8-port extension card for SLTs with 2 power failure transfer (PFT) ports. LED Amphenol To extensions Accessories and User-supplied Items Accessories (included): Screws × 2, Ferrite core × 1 User-supplied (not included): Amphenol connector Notes • • • 96 Attach the included ferrite core to the cable. Refer to "2.2.8 Attaching a Ferrite Core". To connect the Amphenol connector, refer to "2.2.
2.5 Information about the Extension Cards Pin Assignments Amphenol Connector 50 26 25 1 No. Signal Name Function No.
2.5 Information about the Extension Cards 2.5.6 EXT-CID Card (KX-TDA0168) Function Sends Caller ID signals to extension ports. To be mounted on the SLC8 card only.
2.5 Information about the Extension Cards 2.5.7 SLC16 Card (KX-TDA0174) and MSLC16 Card (KXTDA0175) Function SLC16: 16-port extension card for SLTs with 4 power failure transfer (PFT) ports. MSLC16: 16-port extension card for SLTs with Message Waiting Lamp control and 4 power failure transfer (PFT) ports. Maximum output of 145 V/85 V for Message Waiting Lamp control.
2.5 Information about the Extension Cards Pin Assignments Amphenol Connector 50 26 25 1 No. Signal Name Function No.
2.5 Information about the Extension Cards 2.5.8 IP-EXT16 Card (KX-TDA0470) Function 16-channel VoIP extension card. Compliant with Panasonic proprietary protocol, and ITU-T G.729a and G.711 CODEC methods. LEDs RJ45 (10BASE-T/100BASE-TX Full Duplex) To private IP network Accessories and User-supplied Items Accessories (included): Ferrite core × 1 User-supplied (not included): RJ45 connector Notes • • The maximum length of the cable to be connected to this optional service card is 100 m (328 ft).
2.
2.6 Information about the Other Cards 2.6 Information about the Other Cards 2.6.1 OPB3 Card (KX-TDA0190) Function Optional 3-slot base card for mounting a maximum of 3 optional service cards from the following: • DPH4 card • EIO4 card • ECHO16 card • MSG4 card LED Accessories and User-supplied Items Accessories (included): none User-supplied (not included): none CAUTION A LITHIUM BATTERY IS USED IN OPB3 CARD. THERE IS A RISK OF EXPLOSION IF THE BATTERY IS REPLACED WITH THE INCORRECT TYPE.
2.6 Information about the Other Cards 2.6.2 DPH4 Card (KX-TDA0161) Function 4-port doorphone card for 4 doorphones and 4 door openers. To be mounted on the OPB3 card. Fully insert the connectors through the panel openings.
2.6 Information about the Other Cards Pin Assignments 8-pin Terminal Block 1 8 No. Signal Name Function 1 DP4 Doorphone 4 transmit 2 com4 Doorphone 4 receive 3 DP3 Doorphone 3 transmit 4 com3 Doorphone 3 receive 5 DP2 Doorphone 2 transmit 6 com2 Doorphone 2 receive 7 DP1 Doorphone 1 transmit 8 com1 Doorphone 1 receive No.
2.6 Information about the Other Cards 2.6.3 EIO4 Card (KX-TDA0164) Function 4-port external input/output card. To be mounted on the OPB3 card. Fully insert the connectors through the panel openings.
2.6 Information about the Other Cards Pin Assignments 8-pin Terminal Block 1 8 No. Signal Name Function 1 C4b Control 4 2 C4a Control 4 com 3 C3b Control 3 4 C3a Control 3 com 5 C2b Control 2 6 C2a Control 2 com 7 C1b Control 1 8 C1a Control 1 com No.
2.6 Information about the Other Cards External Sensor Power to the external sensor is provided from the EIO4 card and must be grounded through the EIO4 card as indicated in the diagram below. A pair of "sensor" and "common" lines are connected to the EIO4 card for each external sensor. The Hybrid IP-PBX detects input from the sensor when the signal is under 100 Ω. Connection Diagram Hybrid IP-PBX OPB3 EIO4 +5V 33 10K I/O 4.7K External Sensor +5V sensor 33 common 4.
2.6 Information about the Other Cards 2.6.4 ECHO16 Card (KX-TDA0166) Function 16-channel card for echo cancellation during conferences. To be mounted on the OPB3 card. OPB3 Card inside ECHO16 Card Screw Accessories and User-supplied Items Accessories (included): Screws × 3 User-supplied (not included): none Note To establish a conference call involving 6 to 8 parties, install an ECHO16 card and enable echo cancellation for conferences using the KX-TDA Maintenance Console.
2.6 Information about the Other Cards 2.6.5 MSG4 Card (KX-TDA0191) Function 4-channel message card. To be mounted on the OPB3 card.
2.6 Information about the Other Cards 2.6.6 CTI-LINK Card (KX-TDA0410) Function Ethernet card for CTI communication via 10BASE-T port. CSTA Phase 3 protocol compatible. LEDs RJ45 (10BASE-T) To LAN/ Server PC Accessories and User-supplied Items Accessories (included): none User-supplied (not included): RJ45 connector Notes • • The maximum length of the cable to be connected to this optional service card is 100 m (328 ft).
2.
2.7 Connection of Extensions 2.7 Connection of Extensions 2.7.
2.7 Connection of Extensions PT-interface CS DPT APT DHLC8 Card MSLC16, SLC16, SLC8 Cards DLC16, DLC8 Cards " 114 " indicates that the extension card supports the terminal.
2.7 Connection of Extensions 2.7.2 Parallel Connection of the Extensions Any SLT can be connected in parallel with an APT or a DPT as follows. Note In addition to an SLT, an answering machine, a fax machine or a modem (PC) can be connected in parallel with an APT or a DPT. With APT For parallel connection, eXtra Device Port (XDP) mode must be disabled for that port through system programming. Refer to "1.10.9 Paralleled Telephone" and "2.1.
2.7 Connection of Extensions Using an EXtra Device Port With KX-T7600 Series DPT To DHLC8 card 2-conductor wiring cord Connect pins "T" and "R". 4-conductor wiring cord Connect pins "T", "R", "D1" and "D2". DPT SLT TO MAIN UNIT / PABX TO TEL To DHLC8 card To SLT With Other DPT To DHLC8 card 2-conductor wiring cord Connect pins "T" and "R". 4-conductor wiring cord Connect pins "T", "R", "D1" and "D2".
2.7 Connection of Extensions 2.7.3 Digital EXtra Device Port (Digital XDP) Connection A DPT can be connected to another DPT on the Digital XDP connection. In addition, if the DPT is connected to a DHLC8 card, it can also have an SLT connected in Parallel mode or XDP mode. Notes • • • Both DPTs must be KX-T7600 series DPTs (excluding KX-T7640). Parallel mode or XDP mode can be selected through system programming. If XDP mode is enabled through system programming, parallel connection is not possible.
2.7 Connection of Extensions Using an EXtra Device Port To DLC8/DLC16 card To DHLC8 card (for connection of SLT) 4-conductor wiring cord Connect pins "T", "R", "D1" and "D2". 4-conductor wiring cord Connect pins "T", "R", 2-conductor wiring cord "D1" and "D2". Connect pins "T" and "R".
2.7 Connection of Extensions 2.7.4 First Party Call Control CTI Connection CTI connection between a PC and a KX-T7633/T7636 DPT provides first party call control. The CTI connection is made via a USB interface (version 2.0), and uses the TAPI 2.1 protocol. A USB Module (KX-T7601) must be connected to the KX-T7633/T7636 DPT. Note The operating system of the PC required for first party call control depends on your CTI application software. For details, refer to the manual for your CTI application software.
2.8 Connection of 2.4 GHz Portable Stations 2.8 Connection of 2.4 GHz Portable Stations 2.8.1 Overview The following equipment is required to connect the wireless system: CS: Cell Station (KX-TDA0142/KX-T0141) KX-TDA0142 Using a CSIF Card This unit determines the area covered by the wireless system. Up to 3 calls can be made at the same time through each CS. • CSIF4 (KX-TDA0143) One CSIF4 card supports up to 4 Cell Stations. • CSIF8 (KX-TDA0144) One CSIF8 card supports up to 8 Cell Stations.
2.8 Connection of 2.4 GHz Portable Stations Please take into consideration the distance between the CSs when site planning. Please consult a certified dealer for details. However, the required distance between CSs may vary depending on the environment of the installation site and conditions in which the wireless system is used. Conduct the site survey to determine the appropriate distance.
2.8 Connection of 2.4 GHz Portable Stations 2.8.2 Procedure Overview When connecting the wireless system, use extreme care in conducting the site survey. An incorrectly performed site survey can result in poor service area, frequent noise, and disconnection of calls. 1. Investigate the installation site Refer to "2.8.3 Site Planning". a. Obtain a map of the CS installation site. b. Identify the service area required by the user on the map. c.
2.8 Connection of 2.4 GHz Portable Stations 4. Finish the site survey Refer to "2.8.6 After Site Survey". a. Return all DIP switches of each CS to the OFF position, and stop supplying power. b. Turn off the PS. 5. Connect the CS and PS to the Hybrid IP-PBX and test the operation Refer to "2.8.7 Connecting a Cell Station to the Hybrid IP-PBX". a. Connect the CSs to the Hybrid IP-PBX. b. Register the PSs to the Hybrid IP-PBX. c.
2.8 Connection of 2.4 GHz Portable Stations 2.8.3 Site Planning Choosing the best site for the CS requires careful planning and testing of essential areas. The best location may not always be convenient for installation. Read the following information before installing the unit. Understanding Radio Waves Characteristics of Radio Waves The transmission of radio waves and the CS coverage area depend on the structure and materials of the building.
2.8 Connection of 2.4 GHz Portable Stations Object Material Transmission Tendency Wall Concrete The thicker they are, the less radio waves penetrate them. Ferroconcrete Radio waves can penetrate them, but the more iron there is, the more radio waves are reflected. Glass Radio waves usually penetrate them. Glass with wire net Radio waves can penetrate them, but tend to be reflected. Glass covered with heat-resistant film Radio waves are weakened considerably when they penetrate windows.
2.8 Connection of 2.4 GHz Portable Stations CS Coverage Area The example below shows the size of the coverage area of 1 CS if it is installed in an area with no obstacles. Note Radio signal strength levels are measured during the site survey (refer to "2.8.5 Site Survey"). A A Coverage Area Radio signal strength level is greater than "3". (About 50 m to 60 m [164 ft to 197 ft]) B B Gray Zone: Conversation will be intermittent C Good Coverage Area Radio signal strength level is greater than "8".
2.8 Connection of 2.4 GHz Portable Stations one CS becomes weak. However, if a PS moves away from a CS and there are no CSs available for handover, the PS may go out of range and the call could be lost. If the signal from the CS fades, due to the structure of the building, there may be some handover delay. The user will hear a range warning before handover in this case. This also applies in the case of interference from 2.4 GHz apparatus.
2.8 Connection of 2.4 GHz Portable Stations 2.8.4 Before Site Survey Setting and Installing the CS Temporarily for Site Survey 1. Switch the Radio Signal Test switch from OFF to ON. 2. Set the CS number switches as desired. DIP Switch OFF ON 1 2 CS Number Switch 3 4 5 6 CS no. 1 CS no. 2 CS no. 3 CS no. 4 Radio Signal Test Switch CS no. 5 CS no. 6 CS no. 7 CS no. 8 CS no.
2.8 Connection of 2.4 GHz Portable Stations 3. After setting the DIP switch, connect an AC adaptor or battery box to the CS using a power supply adaptor. Note The AC adaptor should be connected to a vertically oriented or floor-mounted AC outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of the adaptor may cause it to become disconnected. Telephone Cord Modular Power Supply Adaptor (PSZZ1TDA0142) To AC Adaptor (KX-A11/KX-TCA1)/ Battery Box (PSZZTD142CE) 4.
2.8 Connection of 2.4 GHz Portable Stations 2.8.5 Site Survey The PS has a Radio Signal Test mode that monitors the state of the radio link to the CS. After installing the CSs temporarily, set the PS to Radio Signal Test mode and measure each CS coverage area. Then, record the results on the map of the installation site. Testing the Radio Signal Strength Note Display prompts for the site survey are only available in English. 1. Enter Radio Signal Test mode.
2.8 Connection of 2.4 GHz Portable Stations 2. Measure the radio signal strength by moving towards and away from the CS. a. Move to the CS until the radio signal strength level becomes "12". b. Move away from the CS and identify the CS coverage area within which the radio signal strength level is greater than "8". Draw the area on the map. c. Move away from the CS and identify the CS coverage area within which the radio signal strength level is greater than "3". Draw the area on the map. PS CS NO.
2.8 Connection of 2.4 GHz Portable Stations b. Overlap the CS coverage areas of at least 2 CSs at any location in the installation site. CS no. 1 CS no. 2 CS no. 3 CS no. 4 c. Make sure that the radio signal strength level is greater than "3" at any location in the service area required by the user. Referring to the Stored Scan Data Using the KX-TD7680 1 9 1 Scan Data No. 0 to 9 Press 1, 9, and POWER for more than 2 seconds. Display example: When there is scan data NO.1 CS No.
2.8 Connection of 2.4 GHz Portable Stations Deleting the Stored Scan Data Using the KX-TD7680 1 9 2 Scan Data No. 0 to 9, or # for all data Press 1, 9, and POWER for more than 2 seconds. To the Desired Scan Data No. Using the KX-TD7690 1 9 Press 1, 9, and POWER for more than 2 seconds. 2 Scan Data No. 0 to 9, or # for all data To the Desired Scan Data No.
2.8 Connection of 2.4 GHz Portable Stations 2.8.6 After Site Survey After obtaining the proper measurement results, exit Radio Signal Test mode before connecting the CS to the Hybrid IP-PBX. 1. Keep pressing the POWER button on the PS until the PS is turned OFF. 2. Disconnect the AC adaptor or battery box from the CS and stop supplying electricity. 3. Switch all DIP switches on the CS from ON to OFF.
2.8 Connection of 2.4 GHz Portable Stations 2.8.7 Connecting a Cell Station to the Hybrid IP-PBX Using a CSIF Card Refer to the following example to connect a CS to the Hybrid IP-PBX. CSIF8 Card Port 1 Cable 26 AWG: 24 AWG: 22 AWG: CAT 5: Maximum Distance 444 m (1457 ft) 694 m (2277 ft) 1000 m (3281 ft) 694 m (2277 ft) CSIF card (RJ45) CS (RJ11) Signal Name D1 POWH POWL D2 Pin No. 1 2 3 4 Pin No.
2.8 Connection of 2.4 GHz Portable Stations Using a DHLC/DLC Card Refer to the following example to connect a CS to the Hybrid IP-PBX. DHLC8 Card Cable 26 AWG: 24 AWG: 22 AWG: CAT 5: Maximum Distance 222 m (728 ft) 347 m (1138 ft) 500 m (1640 ft) 347 m (1138 ft) CS (RJ11) Signal Name D1 D2 Pin No.
2.8 Connection of 2.4 GHz Portable Stations Connecting the CS 1. Connect the cable from the CSIF/DHLC/DLC card to the CS. Modular To CSIF/DHLC/DLC card 2. Pass the cable through the groove of the CS (in any direction depending on your preference).
2.8 Connection of 2.4 GHz Portable Stations Registering the PS The PS must be registered to the Hybrid IP-PBX before it can be used. Programming of both the PS and Hybrid IP-PBX is required. A PT with multiline display (e.g., KX-T7636 6-line display) is required to perform the Hybrid IP-PBX system programming. Note For details about system programming using a PT, refer to "2.3.2 PT Programming" and "3.3 PT Programming" in the Feature Guide.
2.8 Connection of 2.4 GHz Portable Stations PS Registration [690] ENTER PS No. Extn. No. 001 to 128 1 to 4 digits ENTER To the PS operation below END When the PS has not been registered yet When registering the PS for the first time, it is possible to select the desired language for the display. (You do not need to enter the PS system programming mode when registering for the first time.) Using the KX-TD7680 [ F2 ] [ F3 ] Press S2 repeatedly to select the desired language.
2.8 Connection of 2.4 GHz Portable Stations Setting the System Lock When a system lock has been set, the system lock password will be required for PS system setting. Using the KX-TD7680 Choose "Enable/Disable". Select "SYSTEM LOCK". System Lock Password System Lock Password 4 digits 4 digits ENABLE DISABLE C.Tone Using the KX-TD7690 Select "SYSTEM LOCK". SEL SEL CHNG S1 S1 Choose "Enable/Disable". System Lock Password ENTR System Lock Password ENABLE S1 DISABLE ENTR C.
2.8 Connection of 2.4 GHz Portable Stations Setting the Personal Identification Number (PIN) for PS Registration To prevent registering the PS to a wrong Hybrid IP-PBX, a PIN for PS registration can be set to the Hybrid IP-PBX. Before registering the PS to the Hybrid IP-PBX, enter the PIN set to the Hybrid IP-PBX into the PS. By doing so, the PS will only be registered to the Hybrid IP-PBX with the matching PIN. Notes • By default, the PIN for PS registration is "1234" for both the Hybrid IP-PBX and PS.
2.8 Connection of 2.4 GHz Portable Stations PS Termination Confirm the following before canceling the PS registration: • The PS is turned on. • The PS is within range. [691] PS No. 001 to 128 ENTER ENTER If "Rejected" or "Time out" is displayed CLEAR Press "CLEAR". YES To the PS operation below END Press "YES". If the registration information is still stored in the PS Using the KX-TD7680 Select "YES". Select the desired item. Select "DELETE SYSTEM". C.
2.8 Connection of 2.4 GHz Portable Stations 2.8.8 Wall Mounting 1. Place the reference for wall mounting (on the following page) on the wall to mark the 2 screw positions. 2. Install the 2 screws and washers (included) into the wall. Notes • • Make sure that the screw heads are at the same distance from the wall. Install the screws perpendicular to the wall. 3. Hook the CS on the screw heads.
2.8 Connection of 2.4 GHz Portable Stations Reference for Wall Mounting Please copy this page and use as a reference for wall mounting. Install a screw here. 71 mm (2-13/16 in) Install a screw here. Note Make sure to set the print size to correspond with the size of this page. If the dimension of the paper output still deviates slightly from the measurement indicated here, use the measurement indicated here.
2.9 Connection of Doorphones, Door Openers, External Sensors, and External Relays 2.9 Connection of Doorphones, Door Openers, External Sensors, and External Relays 2.9.1 Connection of Doorphones, Door Openers, External Sensors, and External Relays The Hybrid IP-PBX supports a maximum of 16 doorphones, 16 door openers, 16 external sensors, and 16 external relays. Note Doorphones, door openers, external sensors, and external relays are user-supplied.
2.9 Connection of Doorphones, Door Openers, External Sensors, and External Relays 2. Pass the wires through the hole in the base cover, and attach the base cover to a wall using 2 screws. Screw To 8-pin terminal block Note Two kinds of screws are included with a KX-T30865. Please choose the appropriate kind for your wall type. : when a doorphone plate has been fixed to the wall : when you wish to install the doorphone directly onto the wall 3. Connect the wires to the screws located in the front cover.
2.9 Connection of Doorphones, Door Openers, External Sensors, and External Relays 2. Attach the terminal blocks to the connectors of the DPH4/EIO4 card on the Hybrid IP-PBX.
2.10 Connection of Peripherals 2.10 Connection of Peripherals 2.10.1 Connection of Peripherals Maximum Distance 5 m (16 ft) PC CTI Server Cable Maximum Distance 26 AWG to 22 AWG: 10 m (32 ft) CAT 5: 10 m (32 ft) USB BGM/ Music on Hold Cable Maximum Distance 26 AWG to 22 AWG: 10 m (32 ft) CAT 5: 10 m (32 ft) Pager: Amplifier/Speaker Maximum Distance 2 m (6 ft) PC RS-232C Printer BGM/MOH The Hybrid IP-PBX provides Background Music and Music on Hold. Up to 2 external music sources (e.g.
2.10 Connection of Peripherals Pager Up to 2 paging devices (user-supplied) can be connected to the Hybrid IP-PBX. CAUTION External Paging Jacks are SELV ports and should only be connected to approved SELV devices. PC/Printer (via RS-232C) The Hybrid IP-PBX is equipped with an RS-232C interface. This interface provides communication between the Hybrid IP-PBX and the user-supplied devices such as PC or line printers.
2.10 Connection of Peripherals For connecting a printer/PC with a 25-pin RS-232C connector Hybrid IP-PBX (9-pin) Printer/PC (25-pin) Circuit Type (EIA) Signal Name Pin No. Pin No.
2.10 Connection of Peripherals PC/CTI Server (via USB version 2.0) The Hybrid IP-PBX is equipped with a USB interface. This interface provides communication between the Hybrid IP-PBX and a PC or a CTI server. The PC is used for system programming, diagnostics and external system database storage (save/load) functions. The CTI server is used for connecting PCs on a LAN to provide third party call control CTI. The CTI connection uses the CSTA Phase 3 or TAPI 2.1 protocol.
2.11 Power Failure Connections 2.11 Power Failure Connections 2.11.1 Power Failure Connections When the power supply to the Hybrid IP-PBX fails, power failure transfer (PFT) will switch from the current connection to the Power Failure Connection. Refer to "2.4.1 Power Failure Transfer" in the Feature Guide for further information. Connection Power Failure Connection connects a specific SLT and a CO line in the event of power failure.
2.11 Power Failure Connections RJ11 Connector Pin Assignments for CO line Card PFT Ports 1 and 2 1 4 No. Signal Name Function 1 R2 Ring port 2 2 R1 Ring port 1 3 T1 Tip port 1 4 T2 Tip port 2 PFT Ports 3 and 4 (for LCOT16 card only) 1 4 No. Signal Name Function 1 R4 Ring port 4 2 R3 Ring port 3 3 T3 Tip port 3 4 T4 Tip port 4 RJ11 Connector Pin Assignments for Extension Card PFT Ports 1 and 2 1 4 No.
2.12 Starting the Hybrid IP-PBX 2.12 Starting the Hybrid IP-PBX 2.12.1 Starting the Hybrid IP-PBX CAUTION • • • • • SD Memory Card must be inserted in the SD Memory Card slot of the MPR card before startup. Before touching the System Initialize Switch, discharge static electricity by touching ground or wearing a grounding strap. Once you have started the Hybrid IP-PBX and if you unplug the Hybrid IP-PBX, do not perform the following procedures to start the Hybrid IP-PBX again.
2.12 Starting the Hybrid IP-PBX 2. Plug the AC power cord into the Hybrid IP-PBX and an AC outlet, and turn on the Hybrid IP-PBX. The RUN indicator will flash. Note For safety reasons, do not stretch, bend, or pinch the AC power cord. To AC Outlet 3. While the RUN indicator is flashing, slide the System Initialize Switch back to the "NORMAL" position. Depending on the configuration, initialization takes about 1 min to 3 min. If successfully executed, the RUN indicator will stop flashing and stay lit.
2.12 Starting the Hybrid IP-PBX Confirming the CO Line Connection After initialization, program the Hybrid IP-PBX and connect CO lines to the Hybrid IP-PBX. To confirm that the CO lines are successfully connected, dial [ ] [3] [7] + CO line number (3 digits) on a PT, or press the PT's S-CO button. You will hear a dial tone if the CO line is available and connected.
Section 3 Guide for the KX-TDA Maintenance Console Explains the installation procedure, structure, and basic information of the KX-TDA Maintenance Console.
3.1 Overview 3.1 Overview 3.1.1 Overview KX-TDA Maintenance Console is designed to serve as an overall system programming reference for the Hybrid IP-PBX. To program and administer the Hybrid IP-PBX by PC, you need to install the KX-TDA Maintenance Console onto the PC. This manual describes overview and installation of the KX-TDA Maintenance Console only. KX-TDA Maintenance Console*1 Menu Bar Program Menu *1 The contents and design of the software are subject to change without notice.
3.2 Connection 3.2 Connection 3.2.1 Connection Serial Interface Connection USB Port To USB Port PC To COM Port PC RS-232C Port Note For pin assignments and maximum cabling distance, refer to "2.10.1 Connection of Peripherals". LAN Connection via CTI-LINK Card RJ45 Switching Hub To network port PC Note For pin assignments and maximum cabling distance, refer to "2.6.6 CTI-LINK Card (KX-TDA0410)".
3.2 Connection External Modem Connection Modem To RS-232C port (25-pin) To CO line/Hybrid IP-PBX extension port assigned as the CO line destination External Modem (25-pin) RS-232C Port (9-pin) Hybrid IP-PBX (9-pin) Signal Name Pin No. Pin No.
3.3 Installation of the KX-TDA Maintenance Console 3.3 Installation of the KX-TDA Maintenance Console 3.3.
3.3 Installation of the KX-TDA Maintenance Console Starting the KX-TDA Maintenance Console and Assigning the Basic Items (Quick Setup) When you start the KX-TDA Maintenance Console with the Installer Level Programmer Code and connect to the Hybrid IP-PBX for the first time after initialization (with the factory default setting), Quick Setup will launch automatically. During Quick Setup, you will set up the basic items. For details about the basic items, refer to "2.3.3 Quick Setup" in the Feature Guide. 1.
3.3 Installation of the KX-TDA Maintenance Console 7. Follow the instructions of the wizard and assign the basic items (Quick Setup). The program menu appears. You may now begin programming the Hybrid IP-PBX.
3.3 Installation of the KX-TDA Maintenance Console Notes • • • During a long programming session, it is highly recommended that you periodically save the system data to the SD Memory Card. If the Hybrid IP-PBX undergoes a sudden power failure or if the system is reset for some reason, all the system data in RAM will be lost. However, if system data has been saved to the SD Memory Card, it can be easily restored.
Section 4 Troubleshooting This section provides information on the Hybrid IP-PBX and telephone troubleshooting.
4.1 Troubleshooting 4.1 Troubleshooting 4.1.1 Installation PROBLEM Extension does not operate. PROBABLE CAUSE SOLUTION Bad extension card. • Exchange the card for a known working one. Bad connection between the Hybrid IP-PBX and telephone. • Take the telephone and plug it into the same extension port using a short telephone cord. If the telephone works, then the connection between the Hybrid IP-PBX and the telephone must be repaired. A telephone with an A-A1 relay is connected.
4.1 Troubleshooting PROBLEM The ALARM indicator on the front of the shelf turns on red. PROBABLE CAUSE A major system error occurs in the Hybrid IP-PBX. SOLUTION • See the error log using the KX-TDA Maintenance Console (refer to "4.1.5 Troubleshooting by Error Log").
4.1 Troubleshooting 4.1.2 Connection Connection between the Hybrid IP-PBX and a PT: Can you dial an extension? CAUSE No SOLUTION The T/R is connected to the D1/D2. D1 T R D2 D1 T R D2 Hybrid IP-PBX Use the correct cord (the inner 2 wires are for T/R and the outer 2 wires are for D1/D2). Extension Connection between the Hybrid IP-PBX and an SLT: CAUSE SOLUTION The T/R is connected to the D1/D2.
4.1 Troubleshooting Connection between the central office and the Hybrid IP-PBX: (Continued from the previous page.) Can you dial out on a CO line? CAUSE CO line is connected to the T2/T1. T2 R1 T1 R2 No CO line SOLUTION Reconnect the CO line to the T1/R1 or T2/R2 of the telephone jack using 2-conductor wiring. Hybrid IP-PBX CO line is connected to the T2/R1.
4.1 Troubleshooting 4.1.3 Operation PROBLEM PROBABLE CAUSE • SOLUTION • When using the speakerphone on an APT, nothing is audible. • • When using the speakerphone/monitor mode with a DPT, nothing is audible. The "HEADSET" mode is selected by Personal Programming, "Handset/ Headset Selection". • When the headset is not used, select the "HANDSET" mode by Personal Programming. • The PT does not ring. • The ringer volume is off. • Turn on the ringer volume.
4.1 Troubleshooting PROBLEM • PS stays out of service when the CS status is changed from Out of Service to In Service. PROBABLE CAUSE • • It may take about 20 s for CS to start up after the status has been changed to In Service. SOLUTION Wait until the CS starts up.
4.1 Troubleshooting 4.1.4 Using the Reset Button If the Hybrid IP-PBX does not operate properly, use the Reset Button. Before using the Reset Button, try the system feature again to confirm whether there definitely is a problem or not. CAUTION In order to avoid possible corruption of data on the SD Memory Card, please ensure that the "SD ACCESS" LED is off before pressing the Reset Button.
4.1 Troubleshooting 4.1.5 Troubleshooting by Error Log When a major system error occurs in the Hybrid IP-PBX, the ALARM indicator on the front of the shelf turns on red, and the system logs the error information. Error Log Display Format Below is the display format of the error log. To see the error log using the KX-TDA Maintenance Console, refer to the on-line help of the KX-TDA Maintenance Console.
4.1 Troubleshooting Item 5 Sub Code Description Five-digit sub code (1XXYY) 1: Shelf number XX: Slot number KX-TDA100: 00 to 06 (00: MPR slot; 01 to 06: Free slot) KX-TDA200: 00 to 11 (00: MPR slot; 01 to 11: Free slot) YY: Physical port number (01 to 16) For OPB3 card, sub slot number + port number will be displayed. Sub slot 1: 11 to 14 Sub slot 2: 21 to 24 Sub slot 3: 31 to 34 Note When there is no parameter for slot and physical port number, XX and YY will be displayed as "00".
4.1 Troubleshooting List of Errors and Solutions The tables below list the errors and their solutions. When an error whose error code is indicated with "*" occurs in the Hybrid IP-PBX, the ALARM indicator on the front of the shelf turns on red, and the system logs the error information. When the error conditions indicated by the error codes "021", "091", "092", "230", and "510" are recovered, the ALARM indicator will turn off automatically, indicating successful troubleshooting.
4.
4.
4.
4.
4.
4.1 Troubleshooting Error Code 310* Error Message PROBABLE CAUSE Voice Processing System malfunction Ports defective on optional service card: DHLC, DLC • • IP-GW H.323 • Dummy Call Test Error Detection of IP-GW H.
4.
4.
4.
Section 5 Appendix Installation Manual 185
5.1 Revision History 5.1 Revision History 5.1.1 PMPR Software File Version 1.1xxx New Options • System Components Table • KX-TDA0105 Memory Expansion Card (MEC) • KX-TDA0484 4-Channel VoIP Gateway Card (IP-GW4E) • KX-TDA0143 4 Cell Station Interface Card (CSIF4) • KX-T0141 2-Channel Cell Station Unit Using DHLC/DLC Card (PT-interface CS) for 2.4 GHz Portable Station New Contents • 2.7.3 Digital EXtra Device Port (Digital XDP) Connection Changed Contents • 186 1.4.
5.1 Revision History 5.1.2 PMPR Software File Version 2.0xxx New Options • System Components Table • KX-TDA0490 16-Channel VoIP Gateway Card (IP-GW16) • KX-TDA0470 16-Channel VoIP Extension Card (IP-EXT16) • KX-TDA0164 4-Port External Input/Output Card (EIO4) • KX-TDA0168 Extension Caller ID Card (EXT-CID) • KX-TDA0920 SD Memory Card for Software Upgrade to Enhanced Version Changed Contents • • 1.4.3 System Capacity 2.9.
5.1 Revision History 5.1.3 PMPR Software File Version 3.0xxx Changed Contents • • 188 1.4.3 System Capacity 3.3.
Index Installation Manual 189
Index Numerics 16-Channel Echo Canceller Card (KX-TDA0166) 25, 109 26, 101 16-Channel VoIP Extension Card (KX-TDA0470) 26, 84 16-Channel VoIP Gateway Card (KX-TDA0490) 16-Port Analog Trunk Card (KX-TDA0181) 26, 73 25, 94 16-Port Digital Extension Card (KX-TDA0172) 25, 99 16-Port Single Line Telephone Extension Card (KX-TDA0174) 16-Port Single Line Telephone Extension with Message Lamp Card (KXTDA0175) 25, 99 120 2.4 GHz Portable Station 2.4 GHz Portable Station, After Site Survey 134 128 2.
Index K KX-TDA Maintenance Console, Connection 159 161 KX-TDA Maintenance Console, Installation 158 KX-TDA Maintenance Console, Overview KX-TDA Maintenance Console, Password Security 9 162 KX-TDA Maintenance Console, Quick Setup 161 KX-TDA Maintenance Console, System Requirements KX-TDA0103 (L-Type Power Supply Unit) 25, 44 25, 44 KX-TDA0104 (M-Type Power Supply Unit) 25, 71 KX-TDA0105 (Memory Expansion Card) KX-TDA0108 (S-Type Power Supply Unit) 25, 44 25, 86 KX-TDA0143 (4 Cell Station Interface Card) 25,
Index TDA0920) 26, 69 Site Planning, 2.4 GHz Portable Station 124 130 Site Survey, 2.
Index Installation Manual 193
Panasonic Consumer Electronics Company, Division of Panasonic Corporation of North America One Panasonic Way, Secaucus, New Jersey 07094 Panasonic Puerto Rico, Inc. San Gabriel Industrial Park, Ave. 65 de Infantería, Km. 9.5, Carolina, Puerto Rico 00985 http://www.panasonic.com/csd Copyright: This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use only.
