Operating Instructions Color CCTV Camera Model No. WV-CW324LE WV-CW324LE Series WV-CF314LE Series WV-CF314LE This manual covers the models: WV-CW324LE Series (WV-CW324LE, WV-CW314LE, WV-CW304LE) and WV-CF314LE Series (WV-CF314LE, WV-CF304LE). Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual.
Preface About the user manuals The operating instructions of the camera consist of 2 sets: these operating instructions (PDF) and Installation Guide. This document explains how to configue the settings of the camera. Refer to the installation guide for further information about how to install the camera. Adobe® Reader® is required to read PDF. When the Adobe® Reader® is not installed on the PC, download the latest Adobe® Reader® from the Adobe web site and install it.
Contents Preface................................................................................... 2 About the user manuals..................................................... 2 Trademarks and registered trademarks............................. 2 About notations.................................................................. 2 Contents................................................................................. 3 About the setup menus .........................................................
About the setup menus Performing each setting item in the setup menu should be completed in advance to use this unit. Perform the settings for each item in accordance with the conditions of the camera shooting area.
Basic operation The operations in the setup menu are performed with the operation buttons after calling up the setup menu on the connected video monitor. The description below explains how to operate the setup menu basically. Screenshots of WV-CF314LE are shown as an example. Screenshot 1 Hold down the [SET] button for about 2 seconds to call up the top screen of the setup menu.
Screen transition diagram CW324L CW314L CW304L CF314L Top screenCF304L MODEL WV-CW324L CAMERA ID OFF CAMERA SYSTEM BACK-FOCUS SPECIAL LANGUAGE END SETUP DISABLE “CAMERA ID” screen **CAMERA ID** 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;!?= +-*/%$ SPACE POSI RET TOP END RESET ................
Screen transition diagram CW324L CW314L CW304L CF314L Top screen MODEL WV-CW314L CAMERA ID OFF CAMERA SYSTEM BACK-FOCUS SPECIAL LANGUAGE END SETUP DISABLE CF304L “CAMERA ID” screen **CAMERA ID** 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;!?= +-*/%$ SPACE POSI RET TOP END RESET ................
CW324L Screen transition diagram CW314L CW304L CF314L CF304L Top screen MODEL WV-CW304L CAMERA ID OFF CAMERA SYSTEM SPECIAL LANGUAGE END SETUP DISABLE “CAMERA ID” screen **CAMERA ID** 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;!?= +-*/%$ SPACE POSI RET TOP END RESET ................
CW324L CW314L Screen transition diagram CW304L CF314L CF304L Top screen MODEL WV-CF314L CAMERA ID OFF CAMERA SYSTEM BACK-FOCUS SPECIAL LANGUAGE END SETUP DISABLE “CAMERA ID” screen **CAMERA ID** 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;!?= +-*/%$ SPACE POSI RET TOP END RESET ................
CW324L CW314L CW304L Screen transition diagram CF314L CF304L Top screen MODEL WV-CF304L CAMERA ID OFF CAMERA SYSTEM SPECIAL LANGUAGE END SETUP DISABLE “CAMERA ID” screen **CAMERA ID** 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;!?= +-*/%$ SPACE POSI RET TOP END RESET ................
Camera title setting [CAMERA ID] This item specified the camera title. The camera title that indicates the camera location and other information about the camera is created with alphanumerics and symbols, and is displayed on the screen. The camera title is named with up to 16 characters. Follow the procedure below to specify the camera title.
Camera operation setting [CAMERA SETUP] The following describes the camera operation settings. The following settings can be configured on the “CAMERA SETUP” screen displayed from the top screen. Refer to page 5 for how to call up the screen. The settings configured on the “CAMERA SETUP” screen will be saved as a scene file. 1. Register a scene file [SCENE1/SCENE2] It is possible to register 2 patterns of scene file.
Follow the procedure below. “CAMERA SETUP” screen “ALC CONT” screen Mask setting screen **ALC CONT**(1) BACK LIGHT COMP OFF BLC OFF ABS **CAMERA SETUP** SCENE1 ALC/ELC ALC SHUTTER OFF AGC ON(LOW) SENS UP OFF WHITE BAL ATW1 DNR HIGH D&N(IR) AUTO2 VMD OFF MASK SET LEVEL .I..... + 0 RET TOP END RET TOP END Step 1 Set “ALC/ELC” to “ALC”, and press the [SET] button. screen appears.
Step 5 Press the [up], [down], [right], and [left] buttons to move the flashing cursor to the area to be masked and press the [SET] button. When the selected area is masked, the masked area will start blinking (between stripes and white). When the flashing cursor is moved to other areas, the masked area will be displayed in white. Repeat the above procedure to mask other areas as necessary. Note: • To cancel the masking, select the masked area to be canceled, and then press the [SET] button.
CW324L CW314L CW324L Note: • • CW324L CW304L CW314L When “ALC/ELC” is set to “ELC” or “ALC+”, only the AUTO mode is enabled. When “SHUTTER” is set to options other than “OFF”, the electronic sensitivity enhancement setting cannot be CW304L CF314L CF304L CW304L CW314L performed and “---” appears. CF304L CF314L CW304L CF314L • When the magnification of “SENS UP” is increased, the screen becomes coarser, more whitish, or more flawed. However, this CF304L CF304L CF314L phenomenon is normal.
Manual fine adjustment of white balance The white balance is manually fine adjusted after white balance automatically adjustment in the automatic color temperature tracking mode (ATW1, ATW2) or automatic white balance control mode (AWC). Follow the procedures below. “CAMERA SETUP” screen **CAMERA SETUP** SCENE1 ALC/ELC ALC SHUTTER OFF AGC ON(LOW) SENS UP OFF WHITE BAL ATW1 DNR HIGH D&N(IR) AUTO2 VMD OFF RET TOP END Area setting screen Fine adjustment screen **ATW1**(1) **ATW1 AREA**(1) R ...I...
“CAMERA SETUP” screen **CAMERA SETUP** SCENE1 ALC/ELC ALC SHUTTER OFF AGC ON(LOW) SENS UP OFF WHITE BAL ATW1 DNR HIGH D&N(IR) AUTO2 VMD OFF RET TOP END “D&N (IR)” screen **D&N(IR) **(1) AUTO2 LEVEL HIGH .I.. DURATION TIME S L BURST(BW) ON FIX IR LED LIGHT RET TOP END Step 1 Move the cursor to “D&N (IR)” and select the mode from the following. AUTO1: Automatically switches between color and black-and-white images in accordance with the illuminance.
Step 5 Move the cursor to “BURST (BW)”, and decide whether or not to provide a burst signal output in the black-and-white mode. ON (default): Provides a burst signal output. OFF: Does not provide any burst signal output. Note: • Images may not be displayed appropriately without burst signals when camera images are displayed in the black-and-white mode depending on a monitor or VTR model to be used. In such a case, set the burst signal output to “ON”.
“CAMERA SETUP” screen **CAMERA SETUP** SCENE1 ALC/ELC ALC SHUTTER OFF AGC ON(LOW) SENS UP OFF WHITE BAL ATW1 DNR HIGH AUTO2 D&N(IR) MOTION DET VMD RET TOP END “MOTION DET” screen **MOTION DET**(1) LEVEL ....I.. 20 DWELL TIME DISPLAY MODE ALARM OFF 2S + MASK SET RET TOP END Setting of motion detection Move the cursor to “VMD”, press the [LEFT ] or [RIGHT ] button to select “MOTION DET”. Step 1 Move the cursor to “MOTION DET” and press the [SET] button. → The “MOTION DET” screen appears.
“MOTION DET” screen Display mode screen **MOTION DET**(1) LEVEL ....I.. 20 DWELL TIME DISPLAY MODE ALARM OFF 2S + MASK SET RET TOP END Step 6 Move the cursor to “Level” and press the [right] or [left] button to adjust the level. Repeat step 5 and 6 to adjust to optimal level. Step 7 Move the cursor to “DWELL TIME ” and select the dwell time from the following.
Camera system setting [SYSTEM SETUP] Performs the settings relating to the camera system such as synchronization, alarm input/output terminal and privacy zone. The following settings can be configured on the “SYSTEM SETUP” screen displayed from the top screen. Refer to page 5 for how to call up the screen. “SYSTEM SETUP” screen **SYSTEM SETUP** SYNC INT PRIVACY ZONE OFF STABILIZER OFF EL-ZOOM OFF UPSIDE-DOWN OFF LDC I...... + 0 RET TOP END 10.
Step 5 Press the [up], [down], [right], and [left] buttons to determine the lower right position of the zone to be set and press the [SET] button. → An asterisk “*” will be displayed after the number and the zone setting will be saved. Step 6 When “ON (2)” is selected for “PRIVACY ZONE”, the mosaic level may be adjusted. The mosaic level may be set through “ZONE LEVEL”. (Range: 1 to 4) Note: • To delete a zone, select the zone number and press the [SET] button after moving the cursor to “DEL”.
Step 2 Move the cursor to “→ PUSH SET” of “ZOOM” and press the [SET] button. → The zoom setting screen appears. Step 3 Adjust the angular field of view by changing the electronic zoom factor (up to 2x) using the [up] or [down] button, and press the [SET] button. Note: • When the zoom factor is incremented, resolution will be deteriorated. Step 4 Move the cursor to “→ PUSH SET” of “PAN/TILT” and press the [SET] button. → The pan/tilt setting screen appears.
CW314L Back focus setting [BACK-FOCUS SETUP] CW324L CW304L CW324L CW314L CF314L CW314L CW304L CF304L Selects the back focus setting type and performs fine adjustment. The following setting can beCW304L configuredCF314L on the “BACK-FOCUS SETUP” screen displayed from the top screen. Refer to page 5 for how to call up the screen. The lens adjustment shall be performed before the back focus adjustment.
Special menu setting [SPECIAL SETUP] The special menu setup is performed including the setting of the camera image quality and the communication configuration when a receiver is used. The following settings are to be configured on the “SPECIAL SETUP” screen displayed from the top screen. Refer to page 5 for how to call up the screen. “SPECIAL SETUP” screen **SPECIAL SETUP** ....I..160 CHROMA GAIN ..I.... 32 AP GAIN .I..... 16 PEDESTAL + PIX OFF CAMERA RESET PUSH SET SER.NO. XXXXXXXX RET TOP END 19.
Step 1 Move the cursor to “PIX OFF” and press the [SET] button. → The “PIX OFF” screen appears. Step 2 Select a number (1 to 16) with which a pixel compensation point is registered and press the [SET] button. → The pixel compensation positioning screen appears. Step 3 Press the [up], [down], [right], and [left] buttons to move the crosshair cursor to the center of the flaw to be corrected and press the [SET] button. → The flaw is corrected and the pixel compensation point is registered.
Camera language selection [LANGUAGE SETUP] A language for the setup menu is selected from the following: The language selection can be made on the “LANGUAGE SETUP” screen displayed from the top screen. Refer to page 5 for how to call up the screen. “LANGUAGE SETUP” screen **LANGUAGE SETUP** LANGUAGE ENGLISH SET RET TOP END Move the cursor to “LANGUAGE” and press the [right] or [left] button to select the target language, then move the cursor to “SET”, and press the [SET] button.
Shortcut operation Use of a system controller with the “Camera function” button allows users to perform the shortcut settings with use of the numeric keypad and camera function button. The available shortcut operations with this unit are shown as follows.
http://panasonic.net http://panasonic.net Importer's name and address to follow rules: Importer's name and address to EU follow EU rules: http://panasonic.net http://panasonic.net Panasonic TestingTesting CentreCentre Panasonic Importer's name and address to follow EU rules: Panasonic Marketing EuropeEurope GmbH GmbH Panasonic Marketing Winsbergring 15, 22525 Hamburg F.R.Germany Winsbergring 15, 22525 Panasonic Testing Centre Importer's name and addressHamburg to followF.R.