Installation Guide Color CCTV Camera Model No. WV-CS580/G WV-CS584E Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual.
We declare under our sole responsibility that the product to which this declaration relates is in conformity with the standards or other normative documents following the provisions of Directives 2006/95/EC and 2004/108/EC. Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft, voldoet aan de volgende normen of andere normatieve documenten, overeenkomstig de bepalingen van Richtlijnen 2006/95/EC en 2004/108/EC.
Contents Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Limitation of liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Disclaimer of warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Limitation of liability THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THE THIRD PARTY'S RIGHT. THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).
Features Super Dynamic 6 (SUPER-D6) Privacy zone function SUPER-D6 can capture clear images of subjects whose illumination is extremely different. The privacy zone function can mask specific areas of the scene from view. New DSP for high sensitivity Patrol function A new noise reduction system lowers minimum illuminance to 0.5 lx in the color mode and 0.04 lx in the black-and-white mode. The patrol function can store manual camera movement routines for automatic playback.
Precautions The following points as well as the contents of "Warning" and "Caution" shall be observed. Refer installation work to the dealer. Installation work requires technique and experiences. Otherwise injury, or damage to this product may result. Be sure to consult the dealer. Do not insert any foreign objects. This could permanetly damage this product. Turn the power off immediately and contact qualified service personnel for service. Do not damage the power cable.
About the self-diagnosis function [Precautions for use] This product has no power switch. When turning off the power, turn off a circuit breaker. To keep on using with stable performance Parts of this product may deteriorate and it may shorten the lifetime of this product when using in locations subject to high temperatures and high humidity. Do not expose this product to direct heat sources such as a heater. When this product malfunctions due to exogenous noise, etc.
Precautions for installation The following points as well as the contents of "Warning" and "Caution" shall be observed. Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation. Installation work shall be performed in accordance with the technology standard of the electric installation.
Screw tightening The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area. Do not use an impact driver. Failure to observe this may cause overtightening and consequently damage to the screws. When a screw is tightened, make the screw at a right angle to the surface. After tightening the screws or bolts, perform visual check to ensure tightening is enough and there is no backlash.
Major operating controls Alarm Input Connector Alarm Output Connector Camera Mounting Base Video Output Connector Data Port (RS485) IMPORTANT Power Cable WARNING Safety Wire Decorative Cover Camera Dome Fix Ring Lens The lens cannot be replaced. Dome Cover The dome cover is easily damaged, And should be handled with care.
DIP switch settings Important: • Before setting up the camera for a configuration where the camera's RS485 data port is used for camera control (pan, tilt, etc.) by the system controller, the camera's DIP switches must be configured to specify the unit number and communication parameters. If DIP switch setting is not performed, the system controller control will not be possible and camera setup will have to be performed again. Be sure to check the DIP switch settings before setting up the camera.
Unit Number (DIP Switch 1) The factory default settings of these DIP switches are all OFF.
Unit Number DIP Switch 1 ON 1 ON 2 3 4 5 6 7 69 8 1 ON 1 2 3 4 5 6 7 70 8 1 1 2 3 4 5 6 7 71 8 1 2 3 4 5 6 7 72 8 1 2 3 4 5 6 7 73 8 1 2 3 4 5 6 7 74 8 1 2 3 4 5 6 7 75 8 78 8 1 2 3 4 5 6 7 76 8 1 2 3 4 5 6 7 79 8 3 4 5 6 7 77 8 1 2 3 4 5 6 7 8 87 1 2 3 4 5 6 7 8 88 2 3 4 5 6 7 8 89 2 3 4 5 6 7 8 90 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7 8 2 3 4 5 6 7
Important: • When using Pelco protocol, make sure that the system works properly before use. Some functions using Pelco protocol may be restricted when this camera and the apparatuses (commercially available) compatible with Pelco protocol operate together. Note: • When using the Unit Number 1 to 96 of Panasonic Protocol and using the Unit Number 32 to 96 of Pelco-D protocol, the unit number setting needs to be configured using the RS485 SET UP menu.
Camera Installation When installing the camera on a wall or a ceiling, please read the important notice below. Important: • Procure 4 screws (M4) to secure the camera to a wall or a ceiling according to the material of the installation area. In this case, wood screws and nails should not be used. For mounting a camera on a concrete wall, use an anchor bolt (for M4) or an AY plug bolt (M4) for securing. (Recommended tightening torque: 1.
Preparing the Camera and Decorative Cover for Side Cable Exit The camera and decorative cover should be prepared as shown below when mounting the camera on a ceiling or wall with its cables (power, video output, RS485, alarm in, alarm out) exiting from the side. Perform this task when using Ceiling Mount Bracket WV-Q126, or Wall Mount Bracket WV-Q118. The camera mounting base needs to be removed in order to prepare the camera.
5. Connect the cables. Please refer to page 20 for the details of connections. 6. Attach the safety wire for securing the camera to the camera mounting base. Pull on the safety wire to make sure its ring is securely connected to the camera mounting base hook. If the dust protect sheet that comes with the camera is affixed to the camera mounting base, remove it before performing the above step. 10.Separate the two parts of the decorative cover (comes with camera).
Uninstalling the Camera Caution: • Make sure you perform the steps below carefully and exactly when uninstalling the camera and decorative cover. Failure to do so creates the risk of damage to the camera. 3. Remove the safety wire from the camera mounting base. Removing the Decorative Cover Note that you need to separate the two parts of the decorative cover in order to remove it. 1. Unhook the two parts of the decorative cover.
Connections Precautions • The following connections should be made by qualified service personnel or system installers in accordance with all local codes. • See the reverse side of the cover page for main lead connection. • Turn off the power at the fuse box before starting the installation work, or it so could result in fire, electric shock, personal injury, and material damage.
Alarm In/Out Ratings Alarm In : 5 V DC pull-up input. Drive capacity of at lease 0.2 mA required. OFF : 4 V to 5 V , or open ON : 1 V DC or less, or short Alarm Out : Open collector output. 16 V DC, maximum drive current: 100 mA OFF : Open ON : 100 mA or less Note: • Do not turn off camera power within 30 seconds after turning it on. Doing so can cause pan, tilt, zoom, or focus to go out of position.
Troubleshooting Before requesting service, check the following symptoms to see if you can solve the problem yourself. If the countermeasures described below do not correct the problem, or if the symptoms you are experiencing are not covered here, contact a quality service person or system installer. Problem Cause and Recommended Action • Is the camera connected correctly? Check the operating instructions that come with your system controller.
Problem Cause and Recommended Action Reference Pages • Check the white balance setting. Operating Instructions • Use the special setup menu to adjust picture quality. Operating Instructions • Is the dome cover or lens of the camera dirty? If so, clean them. 7 Poor picture color Image flicker • If Super Dynamic 6 is turned on, turn it off. Operating Instructions Afterimages in the picture • Check the DNR setting.
Problem Reference Pages Black line appears in the image • Whether or not the connected system controller is set as multiplex vertical driver (VD2)? Menu settings will not change. • Is the password lock function turned on? I forgot the password. • Contact a quality service person or system installer. — Picture does not switch to black-andwhite. • Switching is not performed when the ALARM IN 4 setting is BW. Check the setting.
Problem The camera movement modes (OFF, SEQ, SORT, AUTOPAN, PATROL, AUTOTRACK) setting changes. Cause and Recommended Action Reference Pages • Check the self return function. Operating Instructions Camera position is different from the preset position setting. • Perform REFRESH from the special setup menu. Operating Instructions Picture is different from the position setting. • Adjust the picture using the preset menu and a scene file.
Specifications General WV-CS580 Power Requirements Power Consumption Pick-up Device Effective Pixels Scanning Area Signal Synchronization Scanning Scanning Frequencies Video Output Resolution (Center) Minimum Illumination Dynamic Range S/N Ratio Ambient Operating Temperature Dimensions Mass Finish WV-CS584 220 V - 240 V AC, 50 Hz 24 V AC, 50 Hz 4.6 W 4.3 W 1/4-type interline transfer CCD 976 (H) × 582 (V) 3.66 mm (H) × 2.73 mm (V) PAL Internal (INT) 2:1 interlace Horizontal: 15.625 kHz, Vertical: 50.
Main Functions Controller Interface Coaxial Multiplex System, RS485 Control Functions AGC Title (ID) Zoom Speed Zoom Limit Password Lock Auto Focus Iris Shutter Electronic Sensitivity Enhancement Auto Mode Auto Pan Key Digital Flip SUPER-D6 VMD Alarm Input/Output Pan and tilt, zoom and focus, 256 preset positions, home position, patrol ON (LOW), ON (MID), ON (HIGH), OFF ON, OFF (Preset ID, camera ID, area title: 16 alphanumeric characters) around 6.
Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be accepted on a free of charge basis.
http://panasonic.net Importer's name and address to follow EU rules: Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15, 22525 Hamburg F.R.Germany © Panasonic System Networks Co., Ltd.