Installation Guide Network Camera WV-SW316L/WV-SW316 WV-SW314 WV-SW316LE/WV-SW316E Model No. (This illustration represents WV-SW316.) Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual.
For Europe WARNING: • To prevent injury, this apparatus must be securely attached to the floor/wall/ceiling in accordance with the installation instructions. • The installation shall be carried out in accordance with all applicable installation rules. • The connections should comply with local electrical code.
Contents Important safety instructions.......................................................................................................... 4 Limitation of liability........................................................................................................................ 5 Disclaimer of warranty.................................................................................................................... 5 Preface.......................................................................
Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 6) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 7) Only use attachments/accessories specified by the manufacturer.
Limitation of liability THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THE THIRD PARTY'S RIGHT. THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).
About notations The following notations are used when describing the functions limited for specified models. The functions without the notations are supported by all models. SW316L : The functions with this notation are available when using the model WV-SW316L. SW316 : The functions with this notation are available when using the model WV-SW316. SW314 : The functions with this notation are available when using the model WV-SW314.
About the user manuals There are 2 sets of operating instructions for the WV-SW316L, WV-SW316, WV-SW314 (P model), WV-SW316LE, WV-SW316E (E model) as follows. • Installation Guide: Explains how to install and connect devices. • Operating Instructions (included in the CD-ROM): Explains how to perform the settings and how to operate this camera. Adobe® Reader® is required to read these operating instructions on the provided CD-ROM.
IMPORTANT: • When using a PC that does not meet the above requirements, displaying of images may become slower or the web browser may become inoperable. • Microsoft Windows 7 Starter, Microsoft Windows Vista Starter and Microsoft Windows XP Professional 64-bit Edition are not supported. • When using IPv6 for communication, use Microsoft Windows 7 or Microsoft Windows Vista.
Network security As you will use this unit connected to a network, your attention is called to the following security risks. q Leakage or theft of information through this unit w Use of this unit for illegal operations by persons with malicious intent e Interference with or stoppage of this unit by persons with malicious intent It is your responsibility to take precautions such as those described below to protect yourself against the above network security risks.
Precautions Refer installation work to the dealer. Installation work requires technique and experiences. Failure to observe this may cause fire, electric shock, injury, or damage to this product. Be sure to consult the dealer. Stop the operation immediately when something is wrong with this product.
Do not touch this product, the power cord or the connected cables during thunder. (even in the process of work) Failure to observe this may cause electric shock. Keep SDHC/SD memory cards (option) away from infants and children. SW316L To keep on using with stable performance Do not use this product in hot and humid conditions for a long time. Failure to observe this causes component degradation resulting in life shortening of this product. Do not expose the product to direct heat sources such as a heater.
Transmission interval Image transmission interval may become slow depending on the network environment, PC performance, shooting subject, access number, etc. About SDHC/SD memory card SW316L SW316 • Before inserting the SDHC/SD memory card, turn off the power of this product first. Otherwise, it may cause malfunction or damage data recorded on the SDHC/ SD memory card. Refer to page 28 for descriptions of how to insert/remove an SDHC/SD memory card.
AVC Patent Portfolio License THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD ("AVC VIDEO") AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE.
Precautions for installation Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation. Installing place Contact your dealer for assistance if you are unsure of an appropriate place in your particular environment. • Make sure that the installation area is strong enough to hold this product, such as a concrete ceiling.
Radio disturbance When this product is used near TV/radio antenna, strong electric field or magnetic field (near a motor, a transformer or a power line), images may be distorted and noise sound may be produced. Time & date setting It is necessary to set the time & date before putting this product into operation. Refer to the Operating Instructions on the provided CD-ROM for descriptions of how to perform the settings. Take notice of humidity. Install this product when the humidity is low.
Major operating controls Rear part of sunshield Sunshield Front cover Rear cover Focus ring Tilting table Zoom lock knob Safety wire TO P Zoom ring Tilting lock screw (x2) M A TR AL R EX C M TO T F/ PTI O NI U O O AL A O ZO I IT ET IN S Azimuth adjustment ring Tilting lock screw Panning lock screw SD CHEATE A R / AFRD (This illustration represents WV-SW316.
Mount bracket cover x2 (accessories) (This illustration represents WV-SW316.) SD memory card error indicator/ Auto focus indicator (blinks when adjusting auto focus) Access indicator (lit when accessing) Link indicator (lit when linking) SDHC/SD memory card slot Auto focus (AF) button TELE button Initial set button WIDE button ＜WV-SW316L/WV-SW316＞ Access indicator (lit when accessing) Link indicator (lit when linking) Focus assist (F.A.
WV-SW316L WV-SW316 IR LED Lens Lens cover Packing Monitor output jack ＜WV-SW314＞ Lens Focus lock knob Desiccant attachment position Monitor output jack 18 Zoom lock knob Packing Lens cover
Preparations Caution: • FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY. • The camera mount bracket can be directly mounted on the wall using a junction box (locally procured) embedded in the wall, or a wall with a cable access hole. • The screws that secure the camera mount bracket on a wall are not supplied. Prepare the screws according to the material, structure, strength and other factors of the mounting area and the total weight of objects to be mounted.
Installations / Connections Secure the camera to the camera mount bracket The tilt angle is locked downward at shipment. z Loosen the tilting lock screw approx. 1 rotation and adjust the tilt angle of the camera to the horizontal position. x Tighten the tilting lock screw again after tilt angle adjustment. Note: • Use a hexagonal wrench with width across flats of 4 mm (locally procured) to loosen or tighten the tilting lock screw. Tilting lock screw Horizontal Camera main body Approx.
v Remove the screws from the mounting boss of the safety wire and the mounting boss of the cable clamp. b Secure the safety wire with the screw from the mounting boss. Then, bundle the wire and the cable using the cable clamp and secure them with each screw from the mounting boss as illustrated. IMPORTANT: • Ensure that the safety wire is firmly secured. Recommended tightening torque: 0.59 N·m {0.44 lbf·ft} Connection Caution: • FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY.
c Connect the alarm input/output cable.
Waterproof treatment for the cable joint sections Adequate waterproof treatment is required for the cables when installing the camera with cables exposed or installing it under the eaves. The camera body is waterproof, but the cable ends are not waterproof. Be sure to use the supplied waterproof tape at the points where the cables are connected to apply waterproof treatment in the following procedure.
Connection example when connecting to a network using a PoE hub Powered speaker (option) Monitor for adjustment (for adjustment use only) PoE device (hub) LAN cable (category 5 or better, straight, STP*) Microphone (option) LAN cable (category 5 or better, straight, STP*) PC Powered speaker (option) LAN cable (category 5 or better, straight, STP*) Microphone (option) Monitor for adjustment (for adjustment use only) LAN cable (category 5 or better, straight, STP*) * E model only IMPOR
Secure the camera mount bracket when the camera is directly installed on a wall 6 mm (W) x 10 mm (L) {1/4" (W) x 3/8" (L)} (long hole) Use 4 screws (locally procured) to secure the camera mount bracket to a wall or a junction box (locally procured). 46 mm {1-13/16"} 83.5 mm {3-1/4"} 20 mm {13/16"} Cable access hole Mounting screw x4 (locally procured) Camera mount bracket • If a junction box is used, putting the boxes side by side is recommended as illustrated.
• If a junction box is used, putting the boxes side by side is recommended as shown in the illustration at right. (Use unused junction boxes to pass cables through for easy cabling.) View from above (internal) TOP 83.5 mm {3-1/4"} 46 mm {1-13/16"} Unused junction boxes 6 mm (W) x 10 mm (L) {1/4" (W) x 3/8" (L)} (long hole) Junction boxes Mounting screw x4 (locally procured) x Attach the camera mount bracket to the left or right hinges of adapter box.
c Secure the mount bracket cover x2 (accessories) to the camera mount bracket with the 2 mount bracket cover screws (accessories). Mount bracket cover x2 (accessories) IMPORTANT: • Ensure that the mount bracket cover screws (accessory) are firmly secured. Recommended tightening torque: 0.59 N·m {0.
Insert/remove an SDHC/SD memory card (WV-SW316L/WV-SW316 Only) IMPORTANT: • Before inserting an SDHC/SD memory card, turn off the power of the camera first. • When inserting an SDHC/SD memory card, make sure the direction. • Before removing the SDHC/SD memory card, select "Not use" for "SD memory card" on the [SD memory card] tab of the setup menu first. Turn off the power after "Not use" selection, and then unload the SDHC/SD memory card.
Adjustment z Be sure to view the monitor for adjustment when the camera angle is adjusted. Supply power to this unit, connect the monitor for adjustment (e.g. a small LCD) to the monitor output jack, and adjust the camera angle (turn off the power after view angle adjustment for safety). q Loosen the 4 fixing screws of the front cover to remove the front cover. w Connect the monitor output jack and the monitor for adjustment with the RCA pin cable (locally procured).
x Adjust the angular field of view and the focus. Adjust the angular field of view in accordance with the distance between the camera lens and a photographic subject. These adjustments shall be performed together with the camera angle adjustment.
Note: • When shooting in the following place or the following subjects, focus may not be adjusted automatically. In this case, adjust the focus manually from the setup menu. Refer to the Operating Instructions (included in the CD-ROM) for how to perform the manual focus adjustment from the setup menu. • Subj. with large illuminance change • Subj. moving frequently • Subj. with reflection or extra brightness • Subj. with low illuminance • Place where the front cover easily becomes dirty • Subj.
w To adjust the angular field of view with a higher zooming effect even after adjusting the angular field of view almost fully in the "T" direction, hold down the focus assist button (F.A.)/extra optical zoom button for 5 seconds or more. 2x extra optical zoom will be applied. When the image capture size under "VGA" is applied, the zoom factor can be adjusted up to 2x without deterioration of image quality. When holding down the focus assist button (F.A.
Mounting the front cover (1) (3) Mount the front cover. (4) (2) Fixing screw x4 Attach the desiccant (accessory) to the inner bottom side of the front cover along the guide rib, and mount the front cover. (1) (3) Guide rib (4) (2) Desiccant (accessory) Fixing screw x4 IMPORTANT: • Be sure to attach the desiccant (accessory). Refer to the instructions for the desiccant for how to attach it.
Attaching the mounting surface on the top surface of the camera body When the mounting surface is changed to the top surface of the camera body z Remove the 4 sunshield fixing screws from the camera body and remove the sunshield. x Remove the 4 tripod head fixing screws from the camera body and remove the tripod head. Tripod head fixing screw x4 Tripod head c Loosen the fixing screw x1 and remove the rear cover, and remove the cap.
b Mount the tripod head on the top of the camera body with the 4 tripod head mounting screws that were removed in the step 2. IMPORTANT: • Caution shall be taken to prevent each cable from being caught between the camera body and tripod head. • Be sure to use the screws that were removed from the tripod head. Recommended tightening torque: 0.59 N·m {0.44 lbf·ft} n Secure the camera to the camera mount bracket with the camera fixing screws x3 (accessory).
m Remove the sunshield backside. As illustrated, opening up the sunshield in both directions makes it easier to remove the rear part of the sunshield. • When installing the camera to a ceiling, the rear part of the sunshield and the fixing screws are not used. Fixing screw x2 Rear part of sunshield , Mount the sunshield on the camera body with the 4 sunshield mounting screws after removing the sunshield backside.
Using the CD-ROM About the CD launcher Insert the provided CD-ROM into the CD-ROM drive of your PC to start up the CD launcher. Then the License Agreement will be displayed. • Read the Agreement and choose "I accept the term in the license agreement", and click [OK]. Then the launcher window will be displayed. • If the launcher window is not displayed, double click the "CDLauncher.exe" file on the CD-ROM. q w e r t Using the supplied CD-ROM, the following actions can be performed.
Installing Panasonic IP setting software On the CD launcher window, click the [Install] button next to [IP Setting Software] to display the Panasonic IP setting software installation window. Confirm the following settings before starting the installation. q w e r q w e r Select the Panasonic IP setting software to install. Select where to create the Panasonic IP setting shortcut icon when the Panasonic IP setting software is installed.
Installing the manuals On the CD launcher window, click the [Install] button next to [Manual] to display the Manual installation window. Confirm the following settings before starting the installation. w q e r t q Select which manuals to install. The camera models that the manuals support are displayed in w "Model List". w The camera models that are supported by the manuals selected in q are displayed here. e Select where to create the manuals shortcut icon when the manuals are installed.
Configure the network settings Configure the network settings of the camera using the Panasonic IP setting software It is possible to perform the network settings of the camera using the IP setup software on the provided CD-ROM. When using multiple cameras, it is necessary to configure the network settings of each camera independently. If the Panasonic IP setting software does not work, configure the network settings of the camera and the PC individually on the "Network" page of the setup menu.
c Complete each network setup item and click the [Save] button. Note: • By unchecking the "Wait for camera restarting." checkbox, multiple cameras can be continuously configured. IMPORTANT: • It may take for around 2 minutes to complete to upload the settings to the camera after clicking the [Save] button. The settings may be invalidated when the LAN cable is disconnected before completing the upload. In this case, perform the settings again.
Troubleshooting Before asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below. Symptom Cause/solution Reference pages SW316 When using DC power supply SW316L • Is 12 V DC power supply connected to the 2P power supply cable? → Check whether the connection is appropriately established.
Specifications • Basic Power source: SW316L SW316 12 V DC, PoE (IEEE802.3af compliant) SW314 Power consumption: PoE (IEEE802.3af compliant) SW316L SW316 12 V DC*: 850 mA, PoE 48 V: 200 mA (Class 0 device) SW314 Ambient operating temperature: PoE 48 V: 70 mA (Class 0 device) * FOR UL LISTED MODEL(S), ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY.
• Camera Image sensor: Effective pixels: Scanning area: Scanning system: Minimum illumination: 1/3-type MOS image sensor Approx. 1.3 megapixels 4.80 mm (H) × 3.60 mm(V) {3/16 inches (H) x 5/32 inches (V)} Progressive SW316L Color: 0.3 lx {0.03 footcandle} (F1.3, Auto slow shutter: Off (1/30 s), Gain: On(High)) 0.019 lx {0.0019 footcandle} (F1.3, Auto slow shutter: max. 16/30 s, Gain: On(High))* BW: 0 lx {0.000 footcandle} (F1.
Video analytics Face detection: Privacy zone: VIQS: Camera title on screen: Video motion detection (VMD alarm): • Lens Zoom ratio: On/Off (with the XML notification setting) On/Off (up to 2 zones available) On/Off Up to 20 characters (alphanumeric characters, marks) On/Off On/Off, 4 areas available SW316L SW316 3.2x Extra zoom: 6.4x (at VGA) SW314 3.6x Extra zoom: 7.2x (at VGA) Focal length: SW316L SW316 3.1 mm - 10 mm SW314 Maximum aperture ratio: 2.8 mm - 10 mm SW316L SW316 1:1.3 (WIDE) - 1:3.
• Network Network: Resolution: Image compression method*1 *2: Transmission interval: Audio compression method: Bandwidth control: Protocol: OS*3 *4: Browser: Maximum concurrent access number: FTP client: 46 10BASE-T/100BASE-TX, RJ45 connector Aspect ratio: 4:3 H.264 1280×960/ VGA (640×480)/ QVGA (320×240), max. 30 fps MPEG-4 VGA (640×480)/ QVGA (320×240), max. 30 fps JPEG (MJPEG) 1280×960/ VGA (640×480)/ QVGA (320×240), max. 30 fps Aspect ratio: 16:9 H.264 1280×720/ 640×360/ 320×180, max.
Multi-screen: Compatible SDHC/ SD memory card (option): Cellular phone compatibility: Mobile terminal compatibility*5: Up to 16 camera images can be displayed simultaneously on a multi-screen. (Including the camera itself ) Manufactured by Panasonic SDHC memory card: 4 GB, 8 GB, 16 GB, 32 GB SD memory card: 256 MB, 512 MB, 1 GB, 2 GB (except miniSD card and microSD card) JPEG image, AUX control (by access level) iPad, iPhone, iPod touch (iOS 4.2.
Standard accessories Installation Guide (this document) ......................................................1 pc. Warranty card (P model only) .............................................................1 pc. CD-ROM*1 ........................................................................................1 pc. Code label*2 ......................................................................................1 pc. The following parts are used during installation procedures. 4P alarm cable SW316L .........
Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.
