Installation Guide Included Installation Instructions Network Camera WV-SW458/WV-SW458M WV-SW458E/WV-SW458ME Model No. (This illustration represents WV-SW458.) Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual.
For U.S.A WARNING: • To prevent injury, this apparatus must be securely attached to the floor/wall/ceiling in accordance with the installation instructions. • The installation shall be carried out in accordance with all applicable installation rules. • The connections should comply with local electrical code. CAUTION: • Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Contents Important safety instructions.......................................................................................................... 4 Limitation of liability........................................................................................................................ 5 Disclaimer of warranty.................................................................................................................... 5 Preface.......................................................................
Important safety instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 6) Only use attachments/accessories specified by the manufacturer. 7) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
Limitation of liability THIS PUBLICATION IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THE THIRD PARTY'S RIGHT. THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICAL ERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THE IMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).
Preface The network camera WV-SW458/WV-SW458M is designed to operate using a PC on a network (10BASE-T/100BASE-TX), and can be installed under eaves (sheltered outdoor). By connecting to a network (LAN) or the Internet, images and audio from the camera can be monitored on a PC via a network. Note: • It is necessary to configure the network settings of the PC and its network environment to monitor images from the camera on the PC. It is also necessary to install a web browser on the PC.
About the user manuals There are 2 sets of operating instructions for the WV-SW458, WV-SW458M (P model), WV-SW458E, WV-SW458ME (E model) as follows. • Installation Guide: Explains how to install and connect devices. • Operating Instructions (included in the CD-ROM): Explains how to perform the settings and how to operate this camera. Adobe® Reader® is required to read these operating instructions on the provided CD-ROM.
Note: • For further information about PC system requirements and precautions for when using Microsoft Windows 7, Microsoft Windows Vista, or Windows Internet Explorer, click “Manual” “Open” from the supplied CD-ROM and refer to “Notes on Windows® / Internet Explorer® versions”. • If using Microsoft Windows XP, screen tearing* may occur when the shooting scene drastically changes (for example, while shooting fast-moving subjects) due to the GDI restrictions of the OS.
Network security As you will use this unit connected to a network, your attention is called to the following security risks. q Leakage or theft of information through this unit w Use of this unit for illegal operations by persons with malicious intent e Interference with or stoppage of this unit by persons with malicious intent It is your responsibility to take precautions such as those described below to protect yourself against the above network security risks.
Precautions Refer installation work to the dealer. Installation work requires technique and experiences. Failure to observe this may cause fire, electric shock, injury, or damage to this product. Be sure to consult the dealer. Stop the operation immediately when something is wrong with this product.
Do not rub the edges of metal parts with your hand. Failure to observe this may cause injury. Do not touch this product, the power cord or the connected cables during thunder (even in the process of work). Failure to observe this may cause electric shock. Keep SDXC/SDHC/SD memory cards (option) away from infants and children. Otherwise, they may swallow the cards by mistake. In this case, consult a doctor immediately. Do not damage the power cable.
Code label The code labels (accessory) are required at inquiry for trouble. Use caution not to lose these labels. It is recommended to paste one of the labels onto the CD-ROM case. Discoloration on the color filter of the MOS image sensor • When continuously shooting a bright light source such as a spotlight, the color filter of the MOS image sensor may have deteriorated and it may cause discoloration.
Precautions for installation Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of improper installation or operation inconsistent with this documentation. This product is designed to be installed under eaves. Install the product under eaves to avoid direct sunlight. Do not install this product in a humid or dust-laden environment. Otherwise, lifetime of the internal parts may be shortened.
Procure fixing screws separately. The screws that secure this product are not supplied. Prepare them according to the material and strength of the area where the product is to be installed. Do not remove or loosen the screws on the rear of this product. If the screws (7 pcs.) are loosened, water exposure may cause damage or malfunction of the product, or dropping may result in injury.
Major operating controls Dome cover * Do not touch the dome cover with your bare hands.
SD memory card slot cover SD memory card slot INITIAL SET button Link indicator (lit when linking) SD memory card error indicator Access indicator (blinks when accessing) About the [INITIAL SET] button After turning off the power of the camera, turn on the power of the camera while holding down this button, and wait for about 5 seconds or more without releasing the button. Wait about 2 minutes after releasing the button.
Preparations When installing the camera on a ceiling or a wall, there are 3 methods as specified below. • Using a two-gang junction box (☞ pages 18 and 19) • Installing the camera directly on the ceiling or wall SW458M (☞ page 19) • Using the supplied mount bracket SW458 (☞ pages 20 to 23) IMPORTANT: • Procure 4 screws (M4) to secure the camera attachment (accessory) or the mount bracket (accessory) SW458 to a ceiling or a wall according to the material of the installation area.
Using the side cable access hole SW458M When installing the camera directly on the ceiling or wall with cables exposed, cut out a portion of the enclosure to open a cable access hole. Side cable access hole IMPORTANT: • To prevent injury and protect cables, smooth opened cable access holes of the enclosure with a file or other tool.
Note: • The direction of “gTOP” on the camera attachment (accessory) determines the upwards direction of the image on the PC monitor. • For ceiling mounting: Determine the direction that you want images to be displayed upwards on the PC monitor, and then mount the camera attachment with “gTOP” facing this direction. • For wall mounting: The camera attachment (accessory) shall be mounted with “gTOP” facing upward.
Using the mount bracket (accessory) SW458 Note: • When the camera is mounted on the ceiling or wall with a hole for cable running, or the camera is mounted using open wiring, the mount bracket (accessory) is used. IMPORTANT: • If open wiring is conducted, be sure to use conduits and run the cables inside the tubes to protect the cables from direct sunlight.
x Determine the direction of the mount bracket according to the installation environment (how the cables are wired, etc.) before mounting it to a ceiling or a wall by fixing 4 screws (locally procured). The direction of the camera in relation to the mount bracket is the 4 directions as shown in the illustration. Cable hole IMPORTANT: • For mounting a camera on a concrete surface, use an anchor bolt (M4) or an AY plug bolt (M4) for installing. (Recommended tightening torque M4: 1.6 N·m {1.
Align the direction of the conduit to the direction of the female thread for the conduit on the mount bracket, and mount the mount bracket to hole A or hole B on the ceiling or wall. [For use of the hole A] Conduit Mount bracket (accessory) Female thread for the conduit Fixing screws (4 pcs., locally procured) Note: • Only the same type of holes, A or B, shall be used for mounting.
c In the direction determined in x, fix the camera attachment (accessory) on the mount bracket using the fixing screws (accessory). (Recommended tightening torque: 0.78 N·m {0.58 lbf·ft}) P TO Camera attachment (accessory) Fixing screws (accessory) Note: • The direction of “gTOP” on the camera attachment (accessory) determines the upwards direction of the image on the PC monitor.
Insert/remove an SD memory card IMPORTANT: • When inserting an SD memory card, make sure the direction. • Before removing the SD memory card, select “Not use” for “SD memory card” on the [SD memory card] tab of the “Basic” page first. Turn off the power after “Not use” selection, and then unload the SD memory card. When the SD memory card is inserted or removed with the power on, data in the SD memory card may be damaged.
Connection Caution: • ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY or LIMITED POWER SOURCE. Turn off a circuit breaker before making a connection. Before starting the connection, prepare the required devices and cables. Note: • When using the mount bracket (accessory), it is possible to connect the cables after mounting the camera onto the mount bracket. SW458 • Refer to page 20 when connecting the conduit.
z Connect the microphone/line input cable and the microphone (for use of the audio reception function). Input impedance: 2 kΩ±10 % Recommended cable length: Less than 1 m {3.3 feet} (for microphone input) Less than 10 m {33 feet} (for line input) Recommended microphone: Plug-in power type microphone (option) Connect a monaural mini plug (ø3.5 mm). • Supply voltage: 2.5 V ±0.
IMPORTANT: • Input and output of the External I/O terminal 2 and 3 can be switched by configuring the setting. “Off” is selected by default. It is possible to determine whether or not to receive input from External I/O terminal 2 and 3 (ALARM IN2, 3) by selecting “Off”, “Alarm input”, “Alarm output” or “AUX output” for “Terminal 2” or “Terminal 3” on the [Alarm] tab of the “Alarm” page. Refer to the Operating Instructions on the provided CD-ROM for further information.
Waterproof treatment for the cable joint sections Adequate waterproof treatment is required for the cables when installing the camera with cables exposed or installing it under the eaves. The camera body is waterproof, but the cable ends are not waterproof. Be sure to use the supplied waterproof tape at the points where the cables are connected to apply waterproof treatment in the following procedure.
Connection example when connecting to a network using a PoE hub Powered speaker (option) Microphone (option) PoE device (hub) LAN cable (category 5 or better, straight, STP*) LAN cable (category 5 or better, straight, STP*) PC Powered speaker (option) LAN cable (category 5 or better, straight, STP*) Microphone (option) LAN cable (category 5 or better, straight, STP*) * E model only IMPORTANT: • Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
Installation Camera mounting Installation shall be conducted after turning off each device. z Attach the camera attachment (accessory) on the ceiling or wall. Secure the camera attachment (accessory) to the two-gang junction box (locally procured). (☞ Pages 18 and 19) SW458M Attach the camera attachment (accessory) using the installation template label (accessory). (☞ Page 19) x Connect each cable.
Using the mount bracket SW458 z Attach the camera onto the camera attachment (accessory) while aligning the “OPEN” mark of the camera with the projection of the camera attachment (accessory). Projection IMPORTANT: • When mounting the camera body, cables shall be run between the camera attachment (accessory) and mount bracket as indicated by the arrows in the illustration. * Cable running as indicated by the arrows in the illustration is an example.
x Engage the camera attachment fixing screws of Projection the camera with the screw hole of the camera attachment (accessory) and rotate the camera in the direction of the arrow to secure the camera to the camera attachment (accessory). Rotate the camera until a click is heard so that the projection of the camera attachment (accessory) will be set to the “LOCK” position. c Secure the camera with the camera fixing screw. (Recommended tightening torque: 1.37 N·m {1.
b Accommodate the connected cables inside the cable guide of the camera mount bracket. IMPORTANT: • To prevent the cables from being caught when the base cover (accessory) is attached, keep the cables inside the cable guide. Cable guide Connected cable Cable guide n Attach the base cover (accessory) that was removed according the steps in page 20.
Configure the network settings Configuring the camera so that it can be accessed from a PC The following are descriptions for when the camera with default settings is configured. If you are using firewall software on your PC, the Setup Program may not be able to find any cameras on your network. Configure the setting of the camera after temporarily invalidating the firewall software.
c Select the camera you want to configure, and click [Access Camera]. Note: • When cameras are displayed in [IP Setting Software] screen, click the camera with same MAC address as the MAC address printed on the camera that you want to configure. v It is necessary to install the viewer software “Network Camera View 4S” to display images. Follow the instructions of the wizard to start the installation. • The “Live” page will be displayed.
Troubleshooting Before asking for repairs, check the symptoms with the following table. Contact your dealer if a problem cannot be solved even after checking and trying the solution in the table or a problem is not described below. Symptom Cause/solution Reference pages When using DC power supply • Is 12 V DC power supply connected to the 2P power supply cable? → Check whether the connection is appropriately established.
Specifications • Basic Power source: Power consumption: Ambient operating temperature: Ambient operating humidity: Waterproof: Shock resistance: External I/O terminal cable: Microphone/line input cable: For microphone input: For line input: Audio output cable: Mounting method: Dimensions: Mass: Finish: • Camera Image sensor: Effective pixels: Scanning area: 12 V DC, PoE (IEEE802.3af compliant) 12 V DC*: 540 mA/ 6.5 W PoE 48 V: 125 mA/ 6.
Scanning system: Minimum illumination: Super-Dynamic: Dynamic range: Gain (AGC): Adaptive black stretch: Light control mode setting: ELC (Maximum exposure time): Auto slow shutter: Day & Night (electrical): White balance: Digital noise reduction: Video analytics Face detection: Number of the preset positions: Auto mode: Self return: Privacy zone: VIQS: Camera title on screen: Video motion detection (VMD alarm): 38 Progressive Color: 1.5 lx {0.15 footcandle} (F2.
• Lens Focal length: Maximum aperture ratio: Angular field of view: • Network Network: 0.837 mm 1:2.4 (Fixed) Horizontal: 182° Vertical: 176° SW458 SW458M Resolution: Image compression method*1: 10BASE-T/100BASE-TX, RJ-45 connector (female) 10BASE-T/100BASE-TX, M12 connector (male) 2M Panorama [16:9]/ 2M Double Panorama [16:9]: 1920x1080/640x360/320x180 max.30 fps H.264(1) 640x360/320x180 max.30 fps H.264(2) 1920x1080/640x360/320x180 max.
Image compression method*1: Transmission interval: Audio compression method: Bandwidth control: Protocol: OS*2 *3: Browser: Maximum concurrent access number: FTP client: Multi-screen: Compatible SDXC/SDHC/ SD memory card (option): Cellular phone compatibility: Mobile terminal compatibility (As of September, 2012)*4: JPEG (MJPEG) Image quality: 0 SUPER FINE/ 1 FINE/ 2/ 3/ 4/ 5 NORMAL/ 6/ 7/ 8/ 9 LOW (10 steps: 0-9) Transmission type: PULL/PUSH 0.
Standard accessories Installation Guide (this document) ......................................................1 pc. Warranty card (P model only) .............................................................1 pc. CD-ROM*1 ........................................................................................1 pc. Code label*2 ......................................................................................1 pc. The following parts are used during installation procedures. Camera attachment .............
Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC.