Installation Guide

Parts and functions Step3 Mount (Fix in accordance with the installation method)
■Indicators
Note:
󱾀
Lighting/blinking LED can be turned off with the software settings at any time. (The initial state is lighting or
blinking.) Refer to the Operating instructions, and set the LED to be solid off if necessary.
LINK indicator
When the camera is able to communicate with the connected device
Lights orange
ACT indicator
When data is being sent via the network camera Blinks green (accessing)
■Buttons
•INITIAL SET button (Initializing)
Follow the steps below to initialize the network camera. Retry if the camera does not start up normally.
*

Do not turn off the power of the camera during the process of initialization. Otherwise, it may fail to initialize and
may cause malfunction.
•TELE button
Click the TELE button to adjust the zoom ratio to the “Tele” side.
•WIDE button
Click the WIDE button to adjust the zoom ratio to the “Wide” side.
Turn on the power of the
camera while pressing
the INITIAL SET button
⇨
Turn off the
power of
the camera
Make sure
to release
the button
15 seconds
The camera will start up and the
settings including the network
settings will be initialized
around
2 minutes
⇨⇨
Note:
󱾀 Back end of the microSD memory card does not protrude
over the surface of the microSD slot (the same surface as
the microSD symbol).
■
Insert a microSD memory card
Back end of
the microSD
memory card
microSD memory card
(the side with printing
facing up)
Symbol of
the microSD
microSD slot
■ Remove a microSD memory card
When removing a microSD memory card, reverse the procedure.
① Open the slide cover by placing your finger on the projection of the slide cover and sliding it.
②

Remove the microSD memory card by pushing it down until a click sound is heard while holding the card
with a fi nger to prevent it from popping out.
③
Close the slide cover.
Note:
󱾀
When using a microSD memory card, format it using this product. Refer to the Operating Instructions
for how to format a microSD memory card.
󱾀
Use the compatible microSD memory cards. Refer to our support website <Control No.: C0107> for
latest information about the compatible microSD memory cards.
IMPORTANT:
󱾀
When removing a microSD memory card, make sure to set "SD memory card" to "Not use" on the
[SD memory card] tab of the setup menu before removing the microSD memory card. After removing
the memory card, set back the "SD memory card" to "Use". For information about the setup menu,
refer to the Operating Instructions.
Insert / remove a microSD memory card
① Open the slide cover by placing your finger on the projection of
the slide cover and sliding it.
②

Insert the microSD memory card into the end of the microSD slot
and confi rm that a clicking sound is made.
③
Close the slide cover.
(The right illustration shows an example of WV-U1142.)
Lens
<Top>
Wire engaging hole
<Side>
<Bottom>
<Rear>
Slide cover
1/4-20UNC
fi xing screw hole
(depth 5.5 mm
{7/32 inches})
microSD slot
INITIAL SET button
WIDE button
TELE button
ACT indicator
LINK indicator
RJ45 Network connector
【１】
Mark the position of holes to be made for the ceiling mount bracket
(locally procured) on the attachment position of the ceiling, and make
those holes for attachment.
【1】Attach the safety wire (accessory)
Ceiling
⇨
Wall
Common
󱾀
Determine the mounting height of the camera so that the lowest part of the camera or
the camera mounting bracket after the installation is 2 m 80 cm {110 inches} or higher
from the floor.
②Pass the ring part of the
safety wire through the
wire engaging hole.
①Bend the ring part
of the safety wire.
③Pass the other end of the
safety wire through the ring
part of the safety wire.
Engage the safety wire (accessory) with the wire engaging hole.
Safety wire
(accessory)
【１】
Mark the position of holes to be made for the wall mount bracket (locally
procured) on the attachment position of the wall, and make those holes for
attachment.
【2】

Secure the wall mount bracket (locally
procured) using separately procured fixing
screws or anchors.
Step1 Preparations
Step2 Processing the installation surface (Process in accordance with the installation method)
【2】 Secure the ceiling mount bracket
(locally procured) using separately
procured fixing screws or anchors.
Ceiling mount bracket
(example)
Fixing screws
(locally procured)
Wall mount bracket
(example)
Fixing screws
(locally procured)
Ceiling
Wall
【１】
Loosen the camera mount bracket fi xing
mechanism to freely move the camera mount
bracket.
【2】

Align the screw thread with the fi xing screw
hole of the camera, and rotate the camera
mount bracket to secure the camera.
【１】

Loosen the camera mount bracket fi xing
mechanism to freely move the camera mount
bracket.
【2】

Align the screw thread with the fi xing screw
hole of the camera, and rotate the camera
mount bracket to secure the camera.
1/4-20UNC
fi xing screw hole
(depth 5.5 mm
{7/32 inches})
Camera mount bracket
fi xing mechanism
Camera mount
bracket
Fixing screw hole
Camera mount bracket
fi xing mechanism
Camera mount
bracket
Fixing screw hole
【2】Download and launch the IP Setting Software and connect to the network by
following information described on our support website <Control No.: 0123>.
【1】Turn on the camera.
【3】Adjust the camera direction.
① Loosen the camera mount bracket fi xing mechanism on the camera mount bracket.
②Adjust the direction while watching the screen of the PC on the network.
③Be sure to tighten the lock lever securely after the adjustment.
【4】Adjust the zoom ratio of the
camera.
U1142
U1132
①Open the slide cover by placing your finger on
the projection of the slide cover and sliding it.
②Adjust the zoom ratio using the TELE button
and the WIDE button while watching the screen.
③Close the slide cover.
IMPORTANT:
󱾀
Devices to which power can be supplied to this product are PoE hub and PoE power supplying equipment.
󱾀
Turn off each system’s power supply before making a connection.
Less than 100 m {328 feet}
Ethernet cable (category 5e or better,
straight, 4 pairs (8 pins))
Step4 Making connections
Step5 Adjustment
90°
360°
360°
90°
Ceiling
Wall
Camera mount bracket
fi xing mechanism
Camera mount bracket
fi xing mechanism
Projection of the slide cover
Slide
cover
WIDE button
TELE button
【2】
If necessary, insert a microSD memory card by referring to “Insert /
remove a microSD memory card”.
Attach the safety wire (accessory) to the foundation
area of the architecture or where suffi cient strength
is assured.
【5】Fix the safety wire on the installation surface.
Ceiling
Wall
Washer
(accessory)
Spring
washer
(accessory)
Ceiling mount bracket (example)
Safety wire
(accessory)
Recommended screw M4
(locally procured)
Minimum pull-out strength
24.5 N {5.5 lbf}
Attach the safety wire (accessory) to the foundation
area of the architecture or where suffi cient strength
is assured.
Wall mount bracket
(example)
Safety wire
(accessory)
Washer
(accessory)
Spring
washer
(accessory)
Recommended screw M4
(locally procured)
Minimum pull-out strength
24.5 N {5.5 lbf}
Projection of the slide cover
Slide
cover
Note:
󱾀
After approx. 3 seconds from releasing the TELE button or the WIDE button, the auto focus function
will automatically be executed. Do not touch the camera during execution of the auto focus function.
󱾀
When the resolution is set to higher than 640×360, image quality may deteriorate depending on the
zoom ratio. Refer to our support website <Control No.: C0124> for further information.
Minimum pull-out strength:
Refer to the instruction guide of the wall mount bracket.
Minimum pull-out strength:
Refer to the instruction guide of the ceiling
mount bracket.
IMPORTANT:
󱾀
Be sure to rotate and secure the camera mount bracket.
Rotating the camera places a large burden on the camera
mount bracket, and may cause damage.
【3】
Tighten the camera mount bracket fi xing
mechanism and secure the camera mount
bracket.
IMPORTANT:
󱾀
Be sure to rotate and secure the camera mount bracket.
Rotating the camera places a large burden on the camera
mount bracket, and may cause damage.
【3】
Tighten the camera mount bracket fi xing
mechanism and secure the camera mount
bracket.
IMPORTANT:
󱾀
When adjusting the camera angle, make sure to loosen the camera mount bracket fixing mechanism on
the camera mount bracket before making adjustments. If the camera angle is changed when the camera
mount bracket fixing mechanism is tightened, excessive force is applied to the camera mount bracket
and camera, which may damage them.
U1142
U1132
U1142
U1132