Operating Instructions Color CCTV Camera Model No. WV-CP600/G Series WV-CF614E Series 00 P6 C V- W WV-CP600/G WV-CF614E (Lens is optional for WV-CP600/G Series.) This manual covers the models: WV-CP600/G Series (WV-CP620/G, WV-CP624E, WV-CP600/G, WV-CP604E) and WV-CF614E Series (WV-CF634E, WV-CF614E). Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. The model number is abbreviated in some descriptions in this manual.
Preface About the user manuals The operating instructions of the camera consist of 2 sets: these operating instructions (PDF) and Installation Guide. This document explains how to configue the settings of the camera. Refer to the installation guide for further information about how to install the camera. Adobe® Reader® is required to read PDF. When the Adobe® Reader® is not installed on the PC, download the latest Adobe® Reader® from the Adobe web site and install it.
Contents Preface................................................................................... 2 About the user manuals..................................................... 2 Trademarks and registered trademarks............................. 2 About notations.................................................................. 2 Contents................................................................................. 3 About the setup menus .........................................................
About the setup menus Performing each setting item in the setup menu should be completed in advance to use this unit. Perform the settings for each item in accordance with the conditions of the camera shooting area. List of setup menu Setup item CAMERA ID CAMERA SCENE 1/ SCENE 2 ALC/ELC SHUTTER AGC SENS UP WHITE BAL DNR D&N (IR/ELE) VMD SYSTEM SYNC ALARM IN/OUT CP620 CP600 PRIVACY ZONE STABILIZER EL-ZOOM UPSIDE-DOWN LDC BACK FOCUS CF634 Hides undesired portions in the camera shooting area.
Basic operation The operations in the setup menu are performed with the operation buttons after calling up the setup menu on the connected video monitor. The description below explains how to operate the setup menu basically. Screenshots of WV-CP620/G are shown as an example. Screenshot 1 Hold down the [SET] button for about 2 seconds to call up the top screen of the setup menu.
Screen transition diagram CP620 Top screen “CAMERA ID” screen MODEL WV-CP620 SERIES CAMERA ID OFF CAMERA SYSTEM SPECIAL LANGUAGE **CAMERA ID** 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;&#!?= +-*/%$ SPACE POSI RET TOP END RESET END SETUP DISABLE ................
Screen transition diagram CP600 Top screen “CAMERA ID” screen MODEL WV-CP600 SERIES CAMERA ID OFF CAMERA SYSTEM SPECIAL LANGUAGE **CAMERA ID** 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;&#!?= +-*/%$ SPACE POSI RET TOP END RESET END SETUP DISABLE ................
Screen transition diagram Top screen MODEL WV-CF634 CAMERA ID OFF CAMERA SYSTEM BACK-FOCUS SPECIAL LANGUAGE END SETUP DISABLE CF634 “CAMERA ID” screen **CAMERA ID** 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;&#!?= +-*/%$ SPACE POSI RET TOP END RESET ................
Screen transition diagram Top screen MODEL WV-CF614 CAMERA ID OFF CAMERA SYSTEM BACK-FOCUS SPECIAL LANGUAGE END SETUP DISABLE CF614 “CAMERA ID” screen **CAMERA ID** 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().,'":;&#!?= +-*/%$ SPACE POSI RET TOP END RESET ................
Camera title setting [CAMERA ID] This item specified the camera title. The camera title that indicates the camera location and other information about the camera is created with alphanumerics and symbols, and is displayed on the screen. The camera title is named with up to 16 characters. Follow the procedure below to specify the camera title. Top screen MODEL WV-CP620 SERIES CAMERA ID ON CAMERA SYSTEM SPECIAL LANGUAGE “CAMERA ID” screen **CAMERA ID** 0123456789 ABCDEFGHIJKLM NOPQRSTUVWXYZ ().
Camera operation setting [CAMERA SETUP] The following describes the camera operation settings. The following settings can be configured on the “CAMERA SETUP” screen displayed from the top screen. Refer to page 5 for how to call up the screen. CP600 The settings configured on the “CAMERA SETUP” screen will be saved as a scene file. 1. Register a scene file [SCENE1/SCENE2] It is possible to register 2 patterns of scene file.
About Super Dynamic 6 Functions Subject in the dark area is hard to notice. If there is high contrast between the bright and dark areas in a shooting zone, the dark area becomes less visible because the camera adjusts the iris in accordance with the bright area. Conversely, adjusting the lens brightness for the darker areas causes the brighter areas to become washed out.
Step 4 Press the [up], [down], [right], and [left] buttons to move the flashing cursor to the area to be masked and press the [SET] button. When the selected area is masked, the masked area will start blinking (between stripes and white). When the flashing cursor is moved to other areas, the masked area will be displayed in white. Repeat the above procedure to mask other areas as necessary. Note: • To cancel the masking, select the masked area to be canceled, and then press the [SET] button.
Note: • When “ALC/ELC” is set to “ELC” or “ALC+”, only the AUTO mode is enabled. • When “SHUTTER” is set to options other than “OFF”, the electronic sensitivity enhancement setting cannot be performed and “---” appears. • When the magnification of “SENS UP” is increased, the screen becomes coarser, more whitish, or more flawed. However, this phenomenon is normal. 6. White balance setting [WHITE BAL] The white balance adjustment is selectable from the following.
Manual fine adjustment of white balance The white balance is manually fine adjusted after white balance automatically adjustment in the automatic color temperature tracking mode (ATW1, ATW2) or automatic white balance control mode (AWC). Follow the procedures below. “CAMERA SETUP” screen **CAMERA SETUP** SCENE1 ALC/ELC ALC SHUTTER OFF AGC ON(HIGH) SENS UP OFF WHITE BAL ATW1 DNR HIGH D&N(IR) AUTO1 VMD OFF RET TOP END Area setting screen Fine adjustment screen **ATW1**(1) **ATW1 AREA**(1) R ...I...
“CAMERA SETUP” screen **CAMERA SETUP** SCENE1 ALC/ELC ALC SHUTTER OFF AGC ON(HIGH) SENS UP OFF WHITE BAL ATW1 DNR HIGH D&N(IR) AUTO1 VMD OFF RET TOP END “D&N (IR)” screen **D&N(IR) **(1) AUTO1 LEVEL HIGH .I.. DURATION TIME S L BURST(BW) ON RET TOP END Step 1 Move the cursor to “D&N (IR)” and select the mode from the following. CP620 AUTO1 (default): Automatically switches between color and black-and-white images in accordance with the illuminance.
Step 5 CP620 CF634 Move the cursor to “BURST (BW)”, and decide whether or not to provide a burst signal output in the black-and-white mode. ON (default): Provides a burst signal output. OFF: Does not provide any burst signal output. Note: • Images may not be displayed appropriately without burst signals when camera images are displayed in the black-and-white mode depending on a monitor or VTR model to be used. In such a case, set the burst signal output to “ON”. 9.
Step 2 Move the cursor to “MASK SET” and press the [SET] button. → The mask setting screen appears. “MOTION DET” screen Mask setting screen **MOTION DET**(1) LEVEL ....I.. 20 DWELL TIME DISPLAY MODE ALARM OFF 2S + MASK SET RET TOP END In the masked area, no alarm will be issued even if a moving object is detected. The masked area is set in the same way as the masked area setting in “Light quantity control method selection”.
Setting of scene change detection This function detects a change in the subject state that occurs by covering the camera with a cloth, a cap, or others, or by changing the camera direction largely. Follow the procedure below. “CAMERA SETUP” screen **CAMERA SETUP** SCENE1 ALC/ELC ALC SHUTTER OFF AGC ON(HIGH) SENS UP OFF WHITE BAL ATW1 DNR HIGH D&N(IR) AUTO1 VMD SCENE CHANGE RET TOP END Step 1 Move the cursor to “VMD” and press the [right] or [left] button to select “SCENE CHANGE”.
Camera system setting [SYSTEM SETUP] Performs the settings relating to the camera system such as synchronization, alarm input/output terminal and privacy zone. The following settings can be configured on the “SYSTEM SETUP” screen displayed from the top screen. Refer to page 5 for how to call up the screen. “SYSTEM SETUP” screen **SYSTEM SETUP** SYNC INT ALARM IN/OUT PRIVACY ZONE OFF STABILIZER OFF EL-ZOOM OFF UPSIDE-DOWN OFF LDC I...... + 0 RET TOP END 10.
Configure the alarm output terminal setting Select the operation of the alarm output terminal. Follow the procedure below. “SYSTEM SETUP” screen **SYSTEM SETUP** SYNC INT ALARM IN/OUT PRIVACY ZONE OFF STABILIZER OFF EL-ZOOM OFF UPSIDE-DOWN OFF LDC I...... 0 + “ALARM IN/OUT” screen **ALARM IN/OUT** ALARM IN OFF ALARM OUT OFF RET TOP END RET TOP END Step 1 Move the cursor to "ALARM IN/OUT" and press the [SET] button. → The "ALARM IN/OUT" screen appears.
Step 3 Move the cursor to “POSITION” and press the [SET] button. Step 4 Press the [up], [down], [right], and [left] buttons to determine the left upper position of the zone to be set and press the [SET] button. Step 5 Press the [up], [down], [right], and [left] buttons to determine the lower right position of the zone to be set and press the [SET] button. → An asterisk “*” will be displayed after the number and the zone setting will be saved.
Step 1 Move the cursor to “EL-ZOOM” and select “ON” and press the [SET] button. → The “EL-ZOOM” screen appears. Step 2 Move the cursor to “→ PUSH SET” of “ZOOM” and press the [SET] button. → The zoom setting screen appears. Step 3 Adjust the angular field of view by changing the electronic zoom factor (up to 2x) using the [up] or [down] button, and press the [SET] button. Note: • When the zoom factor is incremented, resolution will be deteriorated.
Back focus setting [BACK-FOCUS SETUP] CF634 CF614 Selects the back focus setting type and performs fine adjustment. The following setting can be configured on the "BACK-FOCUS SETUP" screen displayed from the top screen. Refer to page 5 for how to call up the screen. The lens adjustment shall be performed before the back focus adjustment. "BACK-FOCUS SETUP" screen **BACK-FOCUS SETUP** ABF PUSH SET MANUAL-ADJ C/L B/W AUTO RET TOP END 17.
Special menu setting [SPECIAL SETUP] The special menu setup is performed including the setting of the camera image quality and the communication configuration when a receiver is used. The following settings are to be configured on the "SPECIAL SETUP" screen displayed from the top screen. Refer to page 5 for how to call up the screen. "SPECIAL SETUP" screen **SPECIAL SETUP** ....I..160 CHROMA GAIN ..I.... 20 AP GAIN .I..... 15 PEDESTAL + DISPLAY ALARM PIX OFF COMMUNICATION COAX CAMERA RESET PUSH SET SER.NO.
"SPECIAL SETUP" screen **SPECIAL SETUP** ....I..160 CHROMA GAIN ..I.... 20 AP GAIN .I..... 15 PEDESTAL + DISPLAY ALARM PIX OFF COMMUNICATION COAX CAMERA RESET PUSH SET SER.NO. XXXXXXXX RET TOP END “PIX OFF” screen Pixel compensation positioning screen **PIX OFF** 1 5 9 13 2 6 10 14 000 000 DEL RET TOP END 3 7 11 15 4 8 12 16 1 Step 1 Move the cursor to “PIX OFF” and press the [SET] button. → The “PIX OFF” screen appears.
Camera language selection [LANGUAGE SETUP] A language for the setup menu is selected from the following: The language selection can be made on the “LANGUAGE SETUP” screen displayed from the top screen. Refer to page 5 for how to call up the screen. “LANGUAGE SETUP” screen **LANGUAGE SETUP** LANGUAGE ENGLISH SET RET TOP END Move the cursor to “LANGUAGE” and press the [right] or [left] button to select the target language, then move the cursor to “SET”, and press the [SET] button.
Shortcut operation Use of a system controller with the “Camera function” button allows users to perform the shortcut settings with use of the numeric keypad and camera function button. The available shortcut operations with this unit are shown as follows.
http://panasonic.net http://panasonic.net Importer's name and address to follow rules: Importer's name and address to EU follow EU rules: http://panasonic.net http://panasonic.net Panasonic TestingTesting CentreCentre Panasonic Importer's name and address to follow EU rules: Panasonic Marketing EuropeEurope GmbH GmbH Panasonic Marketing Winsbergring 15, 22525 Hamburg F.R.Germany Winsbergring 15, 22525 Panasonic Testing Centre Importer's name and addressHamburg to followF.R.
