Instruction Manual
Table Of Contents
- Preface
- Contents
- About the setup menus
- Camera title setting [CAMERA ID]
- Camera operation setting [CAMERA SETUP]
- 1. Register a scene file [SCENE1/SCENE2]
- 2. Light quantity control method selection [ALC/ELC]
- 3. Electronic shutter setting [SHUTTER]
- 4. Gain control setting [AGC]
- 5. Electronic sensitivity enhancement setting [SENS UP]
- 6. White balance setting [WHITE BAL]
- 7. Digital noise reduction function setting [DNR]
- 8. Black-and-white mode setting [D&N (IR) ] CP620 CF634 [D&N (ELE) ] CP600 CF614
- 9. VMD setting [VMD]
- Camera system setting [SYSTEM SETUP]
- Back focus setting [BACK-FOCUS SETUP] CF634 CF614
- Special menu setting [SPECIAL SETUP]
- 20. Chroma level adjustment [CHROMA GAIN]
- 21. Aperture level adjustment [AP GAIN]
- 22. Pedestal level adjustment [PEDESTAL]
- 23. Display Settings [DISPLAY]
- 24. Pixel compensation [PIX OFF]
- 25. Communication setting [COMMUNICATION] CP620 CP600
- 26. Default resetting [CAMERA RESET]
- 27. Serial number viewing [SER.NO.]
- Camera language selection [LANGUAGE SETUP]
- Shortcut operation
17
Step 5
Move the cursor to “BURST (BW)”, and decide whether or not to provide a burst signal output in the black-and-white mode.
ON (default): Provides a burst signal output.
OFF: Does not provide any burst signal output.
Note:
• Imagesmaynotbedisplayedappropriatelywithoutburstsignalswhencameraimagesaredisplayedintheblack-and-white
mode depending on a monitor or VTR model to be used. In such a case, set the burst signal output to “ON”.
9. VMD setting [VMD]
The VMD function allows the camera to detect motion and scene change with the camera. Detection of motion or scene change with
the camera can be announced by issuing an alarm signal.
Important:
• Thefollowingcircumstancesmayresultindetectionfailureorfalsedetection.Usethecameraafteradjustingthedetectionarea
and sensitivity.
•Notenoughdifferenceinbrightnessbetweenthebackgroundandthemovingphotographicsubject,orsignificantchangesin
brightness
•Dirtorwaterdropsonthelens
•Insufficientbrightness,forexample,whenshootingatnight
•Thesubjectismovingstraightatthecamera
•Thesubjectismovingtoofastortooslow
•Thesubjectistoosmallortoolarge
•Therearetoomanymovingobjects
•Lightreflectedthroughawindoworfromaroadsurface
•Thecameraisshaking
•Entryofoutsidelight,suchassunlightortheheadlightsofacar
•Flickering fluorescent light
• Subjectchangedetectionmayfailinthefollowingcases.
•Thelensispartiallycoveredorcoveredwithatransparentitem
•Thephotographicsubjectsbeforeandafterchangingthecameradirectionaresimilar
• Falsedetectionmayoccurforapprox.1minuteafterturningonthepower,aftercompletingsettingsintheSETUPmenu,orafter
changing the camera view angle.
• Motiondetectionisthedetectionfunctionwithinthescreenrangeforelectroniczoomof1x.
“MOTION DET” screen
**
MOTION DET
**(1)
RET TOP END
LEVEL
2S
OFF
DWELL TIME
DISPLAY MODE
ALARM
MASK SET
....
I
..
20
-
+
“CAMERA SETUP” screen
MOTION DET
AUTO1
**CAMERA SETUP**
SCENE1
ALC/ELC ALC
SHUTTER OFF
AGC ON(HIGH)
SENS UP OFF
WHITE BAL ATW1
DNR HIGH
VMD
RET TOP END
D&N(IR)
Setting of motion detection
Move the cursor to “VMD”, press the [LEFT] or [RIGHT ] button to select “MOTION DET”.
Step 1
Move the cursor to “MOTION DET” and press the [SET] button.
→
The “MOTION DET” screen appears.
CP620
CF634