Instruction Manual PAN 118 3in1 Pocket Autoranging DMM Auto Ranging DMM OFF V A AU FF TO PO W ER O DI Ernst KRYSTUFEK GmbH&CoKG AUSTRIA, 1230 Wien, Pfarrgasse 79 Tel +43/1/616 40 10 | Fax +43/1/616 40 10 -21 office@krystufek.at | www.krystufek.
Features • 3-1/2 digit (2000 count) LCD display • Built-in non-contact AC voltage detector plus flashlight • Double Molded housing • CATIII 1000V • 200mA/500V Resettable Fused current inputs and Overload protection on all ranges • Autoranging with auto power off Safety International Safety Symbols This symbol, adjacent to another symbol or terminal, indicates the user must refer to the manual for further information.
Safety Precautions 1. Improper use of this meter can cause damage, shock, injury or death. Read and understand this users manual before operating the meter. 2. Make sure any covers or battery doors are properly closed and secured. 3. Always disconnect the test leads from any voltage source before replacing the battery or fuses. 4. Do not exceed the maximum rated input limits.
Meter Description 1. Non-contact AC voltage detector probe tip 2. Non-contact AC voltage indicator light 3. 3 1/2 Digit (2000 count) 4. MODE button 5. Function switch 6. Flashlight 1 7. Flashlight button 2 8. Data Hold button 3 9. Battery Cover 4 10.
Specifications Electrical Specifications Function DC Voltage Range Accuracy ±(0.5% rdg + 3d) 200mV, 2.000V, 20.00V, 200.0V, ±(1.2% rdg + 3d) 600V AC Voltage 40-400Hz 2.000V, 20.00V ±(1.0% rdg + 8d) 200.0V, 600V ±(2.3% rdg + 10d) DC Current 200.0µA, 2000µA ±(2.0% rdg + 8d) 20.00mA, 200.0mA AC Current 200.0µA, 2000µA ±(2.5% rdg + 10d) 20.00mA, 200.0mA Resistance 200.0Ω ±(0.8% rdg + 5d) 2.000kΩ, 20.00kΩ, 200.0kΩ ±(1.2% rdg + 5d) 2.000MΩ ±(5.0% rdg + 5d) 20.00MΩ ±(10.
Max input voltage Diode Test Continuity Check Display Over range indication Polarity Low Battery Indication Input Impedance AC Response ACV Bandwidth Auto Power Off Fuse Batteries Operating Temperature Storage Temperature Weight Size Standard 600V AC/DC current 1mA max., open circuit voltage of 1.5V typical Audible signal if the resistance is <150Ω 2000 count 3 -1/2 digit LCD LCD displays “OL” Minus (-) sign for negative polarity. “BAT” symbol indicates low battery condition. >7.
Operation AC/DC VOLTAGE MEASUREMENTS CAUTION: Do not measure AC/ DC voltages if a motor On the circuit is being switched ON or OFF. Large voltage surges may occur that can damage the meter. 1. Set the function switch to the green V position. 2. Press the MODE button to indicate “DC” or “AC” on the display. 3. Touch the black test probe tip to the negative side of the circuit. Touch the red test probe tip to the positive side of the circuit. 4. Read the voltage in the display DC/AC CURRENT MEASUREMENTS 1.
RESISTANCE MEASUREMENT WARNING: To avoid electric shock, disconnect power to the unit under test and discharge all capacitors before taking any resistance measurements. Remove the batteries and unplug the line cords. 1. Set the function switch to the Ω position. 2. Press the MODE button to indicate Ω on the display. 3. Touch the test probe tips across the circuit or part under test.
Non-Contact AC Voltage Measurements WARNING: Risk of Electrocution. Before use, always test the Voltage Detector on a known live circuit to verify proper operation 1. Touch the probe tip to the hot conductor or insert into the hot side of the electrical outlet. 2. If AC voltage is present, the detector light will illuminate. NOTE: The conductors in electrical cord sets are often twisted.
REPLACING THE BATTERY 1. Remove the bottom cover and secure the screw. 2. Replace old battery with fresh Two 1.5V AAA type battery. 3. Replace the bottom cover and secure the screw.
