Cut Sheet

www.panduit.com
specifications
LDS non metallic surface raceway will be a one piece, solid
raceway used to route, protect, and conceal data network, voice
or power cabling. The raceway shall be listed as suitable for use
in applications having up to 600 volts between conductors by
Underwriters Laboratories, Inc. per standard 5A when screw
secured with mounting straps and per installation instructions.
The raceway shall be manufactured from impact resistant
material with flammability rating of UL94V-0. A full complement
of power, 1" bend radius control, and standard snap on fittings
must be available. All fittings and boxes shall be tamper resistant
to prevent unauthorized access to cables. LDS raceway finish
shall be pure color and will resist scratches and dents and will
not peel or corrode.
Pan-Way
®
LDS Surface Raceway System
SPECIFICATION SHEET
applications
Pan-Way
®
LDS Profile Raceway is a single
channel non-hinged raceway which provides
solutions for routing of power or low voltage
data and fiber optic cabling along perimeter
walls. LDS Raceway is the only non-metallic
raceway that is bendable in low voltage
applications to route around and over
obstructions, has a tamper resistant design
and is available with standard, bend radius
control and power rated fittings.
technical information
Material:
Rigid PVC
Flammability:
UL94V-0; FT4
Voltage rating:
UL 600V / CSA 600V
Colors:
International White (IW), Electric Ivory (EI),
International Gray (IG), or White (WH)
CSI spec form:
LP-CSISPEC-LDS-1
key features and benefits
Tamper resistant design
Solid one-piece design provides increased tamper
resistance over hinged raceway
Available 1" bend radius
control fittings
Cables in the raceway will satisfy the minimum 1" bend
radius requirement, preventing the potential degradation
of cable performance of high performance cabling systems;
meets TIA/EIA standards and many warranty requirements;
contact customer service for specific part numbers
Only non-metallic
bendable raceway
Can route around and over obstructions in low
voltage applications
Standard and power
rated fittings
Most economical fittings for low voltage or power
applications; rated to 600V and tamper resistant; contact
customer service for specific low-voltage fitting part numbers
Non-metallic construction
Lightweight reducing installer fatigue and labor required to
install the raceway; solid color throughout will not chip, peel,
rust or corrode; easy to cut with standard saws and saw
blades reducing the need for special cutting devices
Adhesive backing
Installations are easier and faster reducing the total
installed cost
Available in four
standard colors
Matches a wide variety of colors for various applications
LDS Raceway
3 series: LDS3IW10-A
5 series: LDS5IW10-A
Mounting Straps for
Power Applications
3 series: LMD3IW-Q
5 series: LMD5IW-Q
LDS Raceway
Power-Rated Fittings
Coupler fitting: CFX*IW-X
Right angle
fitting: RAFX*IW-X
Inside corner
fitting: ICFX*IW-X
Outside corner
fitting: OCFC*IW-X
Tee fitting: TFX*IW-X
Four way cross
fitting (LDS5 only): CRFX5IW-X
End cap fitting: ECFX*IW-X
Drop
ceiling/entrance
end fitting: DCEFXIW-X
Right
angle/entrance
end fitting: RAEFXIW-X
Reducer fitting
from size 5 to 3: RFX53IW-X
Reducer fitting
from size 10 to 3: RFX103IW-X
Reducer fitting
from size 10 to 5: RFX105IW-X
For standard colors other than
IW (International White), replace
IW in part number with EI (Electric Ivory),
IG (International Gray), or WH (White).
For LDS3 fittings, replace * with 3.
For LDS5 fittings, replace * with 5.