Cut Sheet

Panduit Bill of Material
IAEBH6
Category 6, RJ45, 8-position, 8-wire black
industrial bulkhead connector with cover.
Part Number
Description
CPM122S-C
Control Panel Switch Cable Tie Mount
FL12X12LG-A
ARC.68-A-C
Adjustable and Releasable Clamp
Slotted sidewall, open finger flexible wiring duct.
ABDCM30-A-C
Dynamic Cable Manager for Panel Strain Relief
PW38F-TL
3/8" Pan-Wrap Split Harness Wrap
Cable Protection and Management
Electrical Noise Reduction and Space Savings
G2X2LG6EMI
2" x 2" PanelMax Shielded Wiring Duct; 6-foot.
SD2EMI
EMI noise shield kit for 2" height Panduit
wiring duct; two 3-foot sections, four bonding
clips, and anti-oxidizing paste.
DRD22LG6
2" height PanelMax DIN Rail Wiring Duct with dual
wiring channels. Base, covers, and DIN rail
fasteners included (DIN sold separately)
CWD2LG6
One-piece corner wiring duct base for use with 2"
height wiring duct.
Grounding/Bonding & Power
UGB2/0-414-12
Universal ground bar accepts #14 – #4 AWG wire
in 12 wire ports and up to a 2/0 AWG main
equipment grounding conductor with a
compression or mechanical connector
BS100445
Braided Bonding Strap, one-hole, insulated, 4.00"
length x 1.06" width
Identification & Safety
C120X150APT-22
Raised Panel Label, Keyhole, 1.2"W x 1.5"H
R050X075V1T
Thermal Transfer, Vinyl, 0.50" W x 0.75" H,
Networking
IAPNG5EWH
IndustrialNet GFCI Data Access Port, Cat 5e
Panduit Bill of Material (cont.)
Part Number
Description
FI2D204
OM2 4-fiber PCF multimode low smoke zero
halogen riser rated indoor breakout cable
UTP28SP1
Cat 6, 28 AWG (small dia) UTP patch cord
with TX6 Modular Plugs
CDPP8RG &
FDME8RG
8-port DIN rail mount copper or fiber patch panel.
Mounting latches securely attach unit to DIN rail
UPS003024024015
Uninterruptible Power Supply (UPS), 35 Watts
for 5 minutes, 24 VDC in/out, DIN rail mount
FSPD504 OM2 4-fiber dielectric conduited, LSZH-Riser rated,
multimode indoor distribution cable for backbones
PSM7004BU-KD
Cat 7, LSZH, 4-pair, stranded, S/FTP shielded
marine copper cable, oil- and fuel-resistant
F91-40-L
Ferrule, non-insulated, 4/0 AWG wire range
About this Configuration
Control panels are being packed with more gear causing challenges with
over crowding, susceptibility to noise, and challenging moves/adds/
changes. This drawing lays out options to address these concerns.
Grounding & Bonding
Grounding and bonding is critical for reliable network communication,
especially dissipating high frequency noise . Utilizing ground bars and
bonding straps is a best practice for grounding.
Cable Protection and Management
Minimizing chaffing, cuts and strains is paramount to achieve high
reliability and designed performance. The key is securing, covering, and
separating cables from hazards.
Electrical Noise Reduction and Space Savings
Mitigating electrical noise and utilizing 3D panel space facilitates higher
density device designs to fit into tight panel layouts or lead to smaller
panel footprint.
Identification & Safety
Moves, adds, and changes need to be done correctly, efficiently and
safely. Identification is critical to guide personnel to make the right
connections and prevent erroneous disconnects. Protect personnel by
preventing contact with hazards while providing same capability
Networking
Ethernet enabled controls, drives, sensing hardware is proliferating.
Panels need to manage network cabling and devices minimizing
environmental impacts like heat, elec noise, vibration ,etc.
For More Information
For more information, contact your local distributor or Panduit Sales rep.
www.panduit.com/ia
[e-mail]