Cut Sheet

www.panduit.com
specifications
Thick Wall Polyolefin Heat Shrink with a 3:1 ratio shall
be used to insulate, seal and protect electrical splices
and terminations where maximum flame retardancy
and exceptional insulating and sealing characteristics
are required. The adhesive-lined inner wall shall seal
and protect against moisture. The heat shrink tube
shall be suitable for direct burial according to UL 486D;
and UL Recognized for sunlight (UV) resistance and
VW-1 flame rating for outdoor applications such as
solar and wind. The thick wall tube shall be CSA
certified and RoHS compliant.
applications
Approved by UL for outdoor, direct sunlight
applications as well as submersible and direct burial
installations, providing excellent cable protection
with an operating temperature up to 230°F (110°C)
with VW-1 flame rating. Ideal for outdoor alternative
energy applications, such as, wind and solar. A
broad soft flame torch or hot air gun can be used to
shrink the tube. Minimum recommended shrink
temperature is 248°F (120°C). Continually move the
heat source around the diameter of the tube, which
will cause the product to recover. The Panduit
heat gun is designed for indoor use only, and the
recovery rate will be slower than using a torch.
Do not scorch the tube.
Thick Wall Polyolefin Heat Shrink Tubing
3:1 Heat Shrink Tubing
Thick Wall Polyolefin
0.40" expanded dia.: HST0.4*
0.75" expanded dia.: HST0.8*
1.10" expanded dia.: HST1.1*
1.50" expanded dia.: HST1.5*
2.00" expanded dia.: HST2.0*
2.70" expanded dia.: HST2.7*
3.00" expanded dia.: HST3.0*
3.50" expanded dia.: HST3.5*
Related products
Adhesive-Lined
Heat Shrink End Caps
0.47" expanded dia.: HSEC0.5-X
0.79" expanded dia.: HSEC0.8-X
1.15" expanded dia.: HSEC1.0-X
1.58" expanded dia.: HSEC1.5-5
2.25" expanded dia.: HSEC2.0-5
3.92" expanded dia.: HSEC4.0-2
Flame Retardant Adhesive-Lined
Heat Shrink End Caps
0.51" expanded dia.: HSECFR0.5-XY
0.75" expanded dia.: HSECFR0.8-XY
1.10" expanded dia.: HSECFR1.0-XY
1.50" expanded dia.: HSECFR1.5-5Y
2.00" expanded dia.: HSECFR2.0-5Y
Heat Gun and Accessories
Heat Gun: HSG-115V-650
Shrink tube reflector
for tubing up to ¾": HSG-A1
Shrink tube reflector
for tubing up to 1½": HSG-A2
*Additional sizes or colors are available. See following
page for complete part number information.
S P ECIFICAT ION SHEET
technical information
Material:
Irradiated cross-linked polyolefin outer wall with an inner wall of hot melt adhesive
UL listed: *
File number E173379 “SEALED WIRE CONNECTOR SYSTEM”
UL recognized: *
(Black only)
File number E342365 “VW-1 and SUNLIGHT RESISTANT”
CSA certified: *
File number 244528
MIL spec:
SAE-AMS-DTL-23053/15 Class 1
Flammability:
Flame retardant meets UL 224 VW-1
Color:
Black and Red
Shrink ratio:
3:1
Voltage rating:
UL 486D Listed for 600V 90°C continuous use
Additionally tested for 1 kV withstand
Continuous operating
temperature:
-67°F to 230°F (-55°C to 110°C)
Shrink temperature:
248°F (120°C)
Water absorption:
0.5% MAX. per ASTM D570
Dielectric strength:
7.9 kV/mm minimum per ASTM D2671
Environmental
compliance:
Compliant per European Directive 2002/95/EC on the Restriction of
Hazardous Substances (RoHS)
Shelf life:
10 years
* = (except HST3.0 and HST3.5 sizes)
key features and benefits
Wet applications:
High impact and abrasion resistance
Suitable for outdoor, direct sunlight and direct burial applications
Resistant to splitting or rupture during installation
Variety of diameters:
Allows optimal sizing for application requirements to provide a lower installed cost
and the flexibility to protect different size electrical and electronic components,
cables, terminals and connectors
Convenient
packaging:
Available in boxes that include 4' lengths to help maintain a manageable
and organized inventory
A variety of shorter lengths are also available
Quality material:
Suitable for use in 600 V applications to comply with UL standards