CM598G STOP READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID NET-ACCESS N-Type Network Cabinets TOOL LIST -Phillips screwdriver -Flatblade screwdriver -22mm socket wrench -15mm socket wrench -13mm socket wrench -8mm socket wrench -7mm socket wrench -T30 Torx bit -T25 Torx bit -6mm Allen key -2.
NET-ACCESS N-Type Network Cabinets (Switch Configurations) INSTRUCTIONS CM598G © Panduit Corp. 2012-2013 NOTE - Some views in this document may vary slightly from your actual cabinet configuration. FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.
INSTRUCTIONS CM598G Table of Contents - Net-Access N-Type Network Cabinets General Cabinet Operation Page Packaging Material Removal……………………………………………...…………… 4-5 Leveling…………………………..
INSTRUCTIONS CM598G Packaging Material Removal Before removal of packaging material: Check tip indicator on the outside of cabinet to ensure cabinet was shipped in the upright position. If tip indicator shows improper handling, inspect cabinet for damage before accepting cabinet. Before handling cabinet: Small glide strips are installed at various locations around the cabinet to protect the cabinet’s finish during shipping. These strips are to be removed prior to handling of cabinet.
INSTRUCTIONS CM598G Packaging Material Removal Before removal of packaging material: Check tip indicator on the outside of cabinet to ensure cabinet was shipped in the upright position. NOTE: Not all configurations include shipping brackets. Shipping Brackets to be discarded after removal.
INSTRUCTIONS CM598G Leveling • • • • Ensure that [4] Leveling Legs are fully retracted Slide Cabinet into final position Lower the [4] Leveling Legs until the cabinet weight is fully supported by only the leveling legs Adjust the [4] Leveling Legs so that the cabinet is level front-to-back and side-to-side Front-to-Back Cabinet Leveling [4] Leveling Legs (use 6mm Allen Key) Side-to-Side Cabinet Leveling Note: When ganging multiple cabinets together, ensure that adjacent cabinets are adjusted to the sa
INSTRUCTIONS CM598G Floor Mounting • • • • Ensure that [4] Leveling Legs are fully retracted If Necessary, secure [2] “Shipping Hold Down Brackets” at front and rear of cabinet See Floor Mounting View below for floor mounting dimensions Attach the anchors to the floor with appropriate hardware for your type of floor [2] Shipping Hold Down Brackets [4] M10 Hex Head Screws (use 15mm socket wrench) Floor Mounting View 131mm [5.16”] DIM A 4X 14mm DIA [0.55”] 291mm [11.
INSTRUCTIONS CM598G Ganging • • • Ensure cabinets are level Secure Ganging Brackets to cabinets at [4] locations shown below Do not use Ganging Brackets to cinch cabinets together IMPORTANT: Ensure cabinets are level by following the guidelines on page 6. Leveling the cabinet prior to ganging is important to ensure proper door operation. [4] Ganging Brackets [8] M6 Torx Screws (use T25 Torx bit) For Technical Support: www.panduit.com/resources/install_maintain.
INSTRUCTIONS CM598G Grounding • • • Attach Grounding Lug or Grounding Bar at any of the [8] location(s) shown below Grounding location is indicated by universal ground symbol Use M5 bonding screw [8] Grounding Lug Locations (Front and Rear of Beams) Note: top cap removed for clarity. For Technical Support: www.panduit.com/resources/install_maintain.
INSTRUCTIONS CM598G Equipment Rail Adjustment • Loosen M10 Hex Head Screw at top and bottom of rear equipment rail • Adjust equipment rail to desired positon • Tighten M10 Hex Head Screw to 30.0 +/- 5.0 N-m [22.1 +/- 3.
INSTRUCTIONS CM598G Overhead Cable Openings • • • • • Remove Bezel Insert to allow for overhead cable entry Cut [8] tabs with wire cutter to open large cable openings - OPTIONAL Install M10 threaded rod into [6] tapped holes, if desired [2] 152.4mm x 152.4mm [6” x 6”] openings can be used to route power overhead PANDUIT COOL BOOTTM products can be used to seal around cables/fiber to prevent hot air recirculation [6] M10 Threaded Holes Removable Inserts Overhead Cable Opening Bezel OPTIONAL [2] 152.
INSTRUCTIONS CM598G Cable Management Fingers (SN15F, SN25F) • • Insert tabs of Cable Management Finger into mounting slots of cabinet post Slide Cable Management Finger inward to lock into place Cable Managment Finger -Insert tabs into cabinet post -Slide inward to lock in place For Technical Support: www.panduit.com/resources/install_maintain.
INSTRUCTIONS CM598G Dual Hinge Door (Operation) NOTE: Door is push-to-close. PANDUIT recommends closing handle after opening door and simply push door when closing Door Function Adjustment (optimize door operation) • Remove Dual Hinge Door from cabinet (or open one side at a time) • VIEW 1 Loosen [2] Hinge Pin Screws at bottom of cabinet and raise by approximately 6 revolutions (6mm [0.
INSTRUCTIONS CM598G Dual Hinge Door (Removal) • • • • Open both swing handles VIEW 1 While supporting weight of door, pull red finger handle to toggle latch of open side of door to CLOSED position (VIEW 4) VIEW 2 Remove door from cabinet frame by pushing top of hinged side of door away from cabinet Lift door off bottom hinge pin Push Door Away From Cabinet (ensure that: both swing handles are open and Latch in CLOSED Position open side latch is toggled to CLOSED position as {See VIEW 4) shown in VIEW 4) R
INSTRUCTIONS CM598G Dual Hinge Door (Installation) • • • • • • • Open both swing handles VIEW 1 Ensure one top latch is OPEN (VIEW 3) and the other is CLOSED (VIEW 4; pull red finger handle to toggle latches) Lift door (with CLOSED bottom latch) onto bottom hinge pin VIEW 2 While supporting weight of door, align OPEN top latch with cabinet and push door against cabinet until latched VIEW 1 Pull red finger handle to toggle top latch of open side to OPEN (VIEW 3) position Close both swing handles Close door
INSTRUCTIONS CM598G Single Hinge Door (Removal and Installation) • • • • VIEW 1 Pull down Compression Sleeve at top door hinge VIEW 1 Pull Single Hinge Door away from cabinet so that Top Hinge Screw fits through cutout of door VIEW 2 Lift bottom of door off Bottom Hinge Pin REVERSE STEPS to install Single Hinge Door Top Hinge Screw Compression Sleeve (Pull down) VIEW 1 VIEW 3 Bottom Hinge Pin VIEW 2 For Technical Support: www.panduit.com/resources/install_maintain.
INSTRUCTIONS CM598G Single Hinge Door (Door Handle Direction Reversal) • • VIEW 1, 2 Remove Top and Bottom Hinge Brackets from current location (remove top hinge screw, if necessary) VIEW 1, 2 Install Top and Bottom Hinge Brackets on opposite side of cabinet (re-install top hinge screw, if necessary) Door Handle Reversal (Lay door on a flat surface) - VIEW 3, 4 • Remove [2] E-clips from Door Handle Cam and exchange positions of Top and Bottom Door Rods • Remove Door Handle Backing Plate and rotate positi
INSTRUCTIONS CM598G Rear Split Doors (Removal and Installation) • • • Open Rear Split Doors to approximately 90º Lift Rear Split Doors up pull doors away from cabinet frame REVERSE STEPS to install Rear Split Doors For Technical Support: www.panduit.com/resources/install_maintain.
INSTRUCTIONS CM598G In-Row Side Panel (Removal and Installation) • Pull [2] Spring Loaded Hinge Pins to release Front Side Panel from cabinet frame • Remove Front Side Panel by pulling panel out of Rear Side Panel channel (towards front of cabinet) • Pull [4] Spring Loaded Hinge Pins to release Rear Side Panel from cabinet frame • REVERSE STEPS to install In-Row Side Panels IMPORTANT: Install Rear Side Panel First In-Row Side Panel Bracket Removal • Remove [2] Torx Screws and remove In-Row Side Panel Brack
INSTRUCTIONS CM598G Split/Hinged Side Panels (N21SPH, N22SPH, N51SPH, N52SPH) • • • VIEW 3 Secure Bottom Support Bracket to cabinet frame with [3] M5 Torx Screws VIEW 1, 2 Secure Vertical Support Bracket to cabinet frame and bottom support bracket with [1] M5 Torx Screw and [2] Hex Nuts See Page 21 for Side Panel Installation Instructions VIEW 1 Vertical Support Bracket (Top) [2] Hex Nuts (use 6mm Socket Wrench) [1] M5 Torx Screw (use T25 Torx bit) VIEW 2 Vertical Support Bracket (Bottom) [3] M5 To
INSTRUCTIONS CM598G Split/Hinged Side Panels (N21SPH, N22SPH, N51SPH, N52SPH) • • • • Open Side Panel to approximately 90º VIEW 1 Lift Top Hinge Point of Side Panel onto top pin of Vertical Support Bracket VIEW 2 Lower Bottom Hinge Point of Side Panel onto bottom pin of Vertical Support Bracket VIEW 3 Close Side Panel and secure top and bottom of Side Panel to cabinet frame with [2] Spring Loaded Hinge Pins VIEW 1 VIEW 3 Lift Top Hinge Point of Side Panel onto Top Pin of Vertical Support Bracket Sprin
INSTRUCTIONS CM598G Caster Kit Installation (NCSTR4) • • • Install [4] Caster Mounting Plates into posts of cabinet (insert bracket into post in an angled position from above mounting location, rotate bracket, and align bracket with mounting holes) Install [2] M5 screws into bottom holes of Caster Mounting Plate through cabinet post (as shown below) Secure [4] Caster Assemblies to Caster Mounting Plates NOTE: Ensure that fixed casters and swivel casters are paired together at front and rear of cabinet C
INSTRUCTIONS CM598G PDU Bracket Kit Installation • • • • • Install [4] M5 Torx Screws into desired top location of cabinet post, as shown below Do not tighten screws - Leave a gap between screw and cabinet post for bracket thickness Place Top PDU Bracket over screw heads and slide up (or down, depending on mounting side of cabinet) Install Bottom PDU Bracket at desired distance from Top PDU Bracket Tighten [8] M5 Torx Screws DO NOT TIGHTEN (Leave Gap Between Screw and Cabinet Post) [4] M5 Torx Screws (u
INSTRUCTIONS CM598G Cabinet Seal Kit Installation • • • • Install Foam Seal to the caster seal brackets on the bottom flange. Install (2) Caster Seal Brackets (1 Left, 1 Right) to the bottom Air dam assembly using (1) M5X0.8 button head torx screw. (do not tighten) Install Equipment Seal to the top of the lower front side to side beam and to the bottom of the upper side to side beam, between the front E-rails. Install foam seal to the rear flange of the front side to side beam.
INSTRUCTIONS CM598G Front and Rear Floor Seal Installation • Install Floor Seal to front or rear of cabinet frame using (2) M10x20mm bolts. (Flange on floor seal will face outward away from the cabinet.) Floor Seal [2] M10x20mm bolts For Technical Support: www.panduit.com/resources/install_maintain.
INSTRUCTIONS CM598G Top of Cabinet Cable Manager Installation • • • • • Disassemble front fascia assemblies (packaged in cabinet) by removing (2) M5x0.8 button head screws (use T25 Torx bit). Remove (2) M5x0.8 button head screws (use T25 Torx bit) from front and rear of Cable Manager base. Install vertical walls on front and back of Cable Manager base using (5) M5x0.8 button head Torx screws (use T25 Torx bit). Re-install screws from previous step to secure to the frame.
INSTRUCTIONS CM598G Top of Cabinet Cable Manager Installation (for vertical exhaust ducts) IMPORTANT - INSTALL VERTICAL EXHAUST DUCT PRIOR TO INSTALLING REAR VERTICAL WALL • Disassemble front fascia assemblies (packaged in cabinet) by removing (2) M5x0.8 button head screws (use T25 Torx bit). • Remove (2) M5x0.8 button head screws (use T25 Torx bit) from front of Cable Manager base. • Install vertical wall on front of Cable Manager base using (5) M5x0.8 button head Torx screws (use T25 Torx bit).
INSTRUCTIONS CM598G This page is left intentionally blank For Instructions in Local Languages and Technical Support: www.panduit.com/resources/install_maintain.asp www.panduit.com Page 28 of 28 E-mail: techsupport@panduit.
