CONTENTS Getting Started INTRODUCTION AND SAFE OPERATION .......................................... 2 GENERAL PRECAUTIONS ...................................................................... 4 WARRANTY INFORMATION ................................................................. 5 GENERAL DESCRIPTION ....................................................................... 6 KEYBOARD & LCD DISPLAY ................................................................ 7 BATTERIES ..................................
ii
Getting started 1
INTRODUCTION AND SAFE OPERATION The LS7 printer was designed specifically to make cable, patch panel, faceplate and facility marking effortless. This palm-sized printer combines high quality thermal transfer print, fas t loading tape cassettes and industrial label materials to eliminate concerns about labels falling off. This manual will guide you step by step through the set-up, operation, and troubleshooting of the LS7 Printer.
Information to USA Users NOTE: This printer has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC rules. These limits are designed to provide reasonable protection against harmful interference when the printer is operated in a commercial environment. This printer generates, uses, and can radiate radio frequency energy and, if not used in accordance with this instruction manual, may cause harmful interference to radio communications .
GENERAL PRECAUTIONS WARNING: Observe the following warnings in order to avoid damage to the LS7 or its acces sories. ● Use only Panduit LS7 tapes with this machine (green colored cassettes). ● Use only the LS7-ACS, AC adapter designed exclusively for this machine. Use of any other adapter will void the warranty. ● Do not use the machine in dusty places, and keep it out of both direct sunlight and rain. ● Do not expose the machine to high temperatures or high humidity.
WARRANTY INFORMATION Our products are warranted to be free from defects in material and workmanship at the time of sale but our obligation under this warranty is limited to the replacement of any product proved to be defective within 6 months (for product) or 90 days (for printers ) from the date of delivery. Printer warranty is void if Panduit printers are modified, altered or misused in any way.
GENERAL DESCRIPTION TOP VIEW AC adapter connector Tape cutte r lever BOTTOM VIEW Battery compartment Ba ck cover Tape release lever Print head Tape compartment Tape exit slot 6
KEYBOARD & LCD DISPLAY LS7 Auto Rotate Underline Tape cutter lever Feed Print Sym.
BATTERIES This lightweight and portable machine can be used anywhere by installing six (6) AA (AM3, LR6) alkaline batteries. When changing the batteries, always replace all six at the same time. To change the batteries: 1 Remove the back cover by pressing in on the rough area at the top end of the machine and pulling off the cover. Pulling off the back cover lifts up the tape release lever. 2 If batteries are already installed, remove them.
OPTIONAL AC ADAPTER The AC adapter (LS7-ACS) allows you to use this machine wherever there is an electrical outlet. To connect the optional AC adapter: 1 Insert the plug on the adapter cord into the connector marked DC IN 9.5V on the bottom end of the machine. 2 Insert the plug on the adapter into the nearest standard electrical outlet. ☞ Only use the AC adapter (par t no. LS7-ACS) designed exclusively for this machine.
TAPE CASSETTE A single LS7 tape cas sette is supplied with this unit. This machine has been designed to allow the tape cassette to be changed quickly and easily. To change the LS7 tape cassette: 1 Remove the back cover by pressing in on the rough area at the top end of the machine and pulling off the cover. Pulling off the back cover lifts up the tape release lever. 2 If a tape cas sette is already installed, remove it by pulling it straight out.
LABEL CODE The “LABEL CODE ” message appears on the display when the following tape cassettes are loaded: Part Number Tape Width Color Label Code LS7-50-1 1/2" (12 mm) Black/White 1 LS7-50-2 1/2" (12 mm) Black/Clear 1 Future — — See Tape Cass ette The Label Code must be entered in order for the printer to function with the tape cassette listed. Future parts may require Label Code entry.
LAMINATED INDUSTRIAL TAPE SEPARATOR TOOL LAMINATED INDUSTRIAL TAPE The enclosed tape separator enables you to easily remove the backing from labels printed on laminated tapes. 1 Hold the tape in one hand, with the printed surface facing up, and hold the tape separator in your other hand. 2 Pass the tape halfway through the long narrow hole in the tape separator. 3 Turn the tape separator three-quarters of a turn towards you, and then pull the tape s eparator away from you as shown below.
PRINT HEAD & ROLLERS Occasionally, specks of dust or dirt become attached to the machine’s print head and rollers. This is particularly likely when you are using the unit outdoors or in a very dus ty environment. If a section of the print head is covered with dust, a blank horizontal streak may appear through the label text. Therefore, the machine’s head may need to be cleaned from time to time. To clean the print head and rollers: 1 Turn off the machine.
Print head Print head Rollers Cotton swab Gently wipe off this black line.
TAPE CUTTER With use, the tape cutter may become covered with adhesive, making it difficult to cut the tape. If the tape cannot be cut correctly, clean the tape cutter blades as explained below. ☞ To avoid injuries, be extremely careful not touch the cutter blades with bare hands. To clean the tape cutter blades: 1 Turn off the machine. 2 Remove the back cover, and then remove the tape cassette if one is installed. The tape cutter is located near the tape exit slot.
CARRYING CASE The enclos ed hard case is designed to protect your LS7 and its acces sories while you store or carry them. Therefore, keep them in this carrying case whenever they are not being used. Before opening the carrying case, be sure that the side with the Panduit logo faces upward. 1 2 LS7 Six AA batteries 3 Tape cassette ☞ Tape Separator Tool 5 AC adapter ☞ Stand up the tape cassettes so that the end with the label attached face s upwards.
For your information 17
POWER KEY The power key ( ) is located in the top right-hand corner of the keyboard. If batteries have been installed or the machine has been plugged in using the optional AC adapter, the previous session’s information is displayed when the machine is turned on. This feature allows you to stop work on a label, turn off the machine, and return to it later without having to re-enter the text. The machine will automatically turn off if no key is pressed within 5 minutes.
CODE & CAPS KEYS Most characters can be entered simply by pressing their keys. However, to use special functions or to enter capital letters, accented characters and s ome symbols, the following special keys are necessary. CODE KEY To use a function or type in characters printed either above or below a key: ● Hold down Code and press the key either immediately below or immediately above the desired function or character written in orange. EXAMPLE To star t the accent function: ● Hold down once.
CAPS KEY To type capital letters continuous ly: 1 Press 2 Press the keys of the desired letters. ☞ Caps until the Caps indicator ( To exit Caps mode, press Caps Caps ) on the left side of the display lights up. until the Caps indicator goes off. EXAMPLE To type in “JOHN”: 1 Press Caps once. Rotate A Caps 1:_ A A A A Auto Underline Frame Length Repeat Legend " 2 Press J onc e ea ch.
CURSOR KEYS The machine’s LCD dis play shows two rows of 11 characters; however, the text that you create can be up to 99 characters long. You can review and edit your text by using the cursor keys ( , Home , , End ) to move the cursor so that different parts are shown in the display. LEFT CURSOR KEY To move the cursor one character to the left: ● Press once. To move the cursor s everal characters to the left: ● Hold down until the cursor moves to the desired position.
UP CURSOR KEY To move the cursor up to the previous line: ● Pres s Home once. To move the cursor up several lines: ● Hold down Home until the cursor moves to the desired pos ition. To move the cursor to the beginning of the entire text: ● Hold down Code and press Home . DOWN CURSOR KEY To move the cursor down to the following line: ● Pres s End once. To move the cursor down several lines: ● Hold down until the curs or moves to the desired position.
SPACE KEY The Space key lets you add blank spaces between characters in your text. It is different from the right cursor key ( ), which just moves the curs or without adding blank spaces. To add a space: ● Press Space . Rotate EXAMPLE To add a space: ● Press Space Rotate .
RETURN KEY File Like on a typewriter or word process or, this machine’s return key ( ) is used to end a line of text and start another one. When you have finished entering one line of text, press the return key to add a return mark ( ) to the end of the line and start a new one. File ☞ A maximum of four text lines can be entered. If you pres s when the cursor is located in the four th line, the error mes sage “4 LINE LIMIT!” will appear.
To add a new line of text: 1 Press , , Home or End to position the cursor to the right of the character that will end the line. File 2 Press . The return mark ( ) appears at the end of the line and the cursor moves to the new line. EXAMPLE To add a second line of text: Rotate A A A A A Auto Underline Caps 1:J o h n S m i t h Frame Length Repeat Legend File ● Press .
To apply a selected item: File ● Pres s once. EXAMPLE To add “ ” to your text: Rotate Caps A A A A A Auto += 1:D A T A _ Underline Frame Length Repeat Legend Feed ● Press Sym.
BACKSPACE KEY Clear The backspace key ( BS ) allows you to remove characters to the left of the cursor’s current position. It differs from the left curs or key ( ), which only moves the cursor without deleting any characters. The backspace key can also be used to quit most functions and return to the previous display without changing the text. ☞ The backspace key cannot be used to quit the barcode function. To quit the barcode function, hold down Code and press N .
Clear 1 Press BS once . Rotate A A A A A Auto Underline Caps 1:12 - 3 4 5 - 6 7 8 To delete “-678”: Frame Length Repeat Legend Clear 2 Hold down BS until “-678” are Rotate A A deleted. A A A Auto Underline 1:0 1 2 - 3 4 5 Caps Frame Length Repeat Legend To quit a function without changing your text: Clear ● Pres s BS to return to your text.
CLEAR FUNCTION The clear function is used to remove all characters from the display so that you can begin entering new text. Although all of the text is erased, the Caps mode does not change. To delete all of the text: Clear ● Hold down Code and press BS . All of the text is erased from the display. EXAMPLE To clear the display: Rotate A A A A A Auto Underline Frame Caps Length Repeat Legend Clear ● Hold down Code and press BS .
ACCENT FUNCTION The accent function can be used to add accented characters to your text. The accented characters are grouped according to the capital or lowercas e letter that they are combined with.
EXAMPLE To add the ac cented character “Ë”: Accent 1 Hold down Code and press O . Rotate Caps A A A A A ACCENT a-u/A-U? Underline Frame Length Repeat Legend 2 Press Caps . Rotate Caps Auto A A A A A Auto ACCENT a-u/A-U? Underline Frame Length Repeat Legend Page 3 Press E . Rotate Caps A A A A A ˜ ÈÉËÊE 1:N O Underline Frame Length Repeat Legend 4 Press until “ Ë” flashes.
SYMBOL FUNCTION In addition to the letters, symbols and numerals on the key tops, there are 9 additional marks available with the symbol function. These symbols are shown below. Symbols Data Fiber Optic Fax Phone + = Plus Equals Caution Shock Hazard Ground To type in a symbol: Feed 1 Press 2 Press 3 Press Sym. . A row of symbols appears in the display. or until the desired symbol flashes. File . The symbol appears in the text.
EXAMPLE To add the symbol “ ”: Feed 1 Press 2 Press Sym. . or until “ ” Rotate flashes. Caps A A A A A Auto += 1:P H O N E Underline Frame Length Repeat Legend File 3 Press .
LENGTH FUNCTION Although the length of the printed label automatically adjusts to fit the length of the entered text, there may be times when you will want to make a label with a specific length. The length function allows you to set the label length between 0.25" and 11.80" (6.4 and 299.7 mm). The default length setting is OFF. If ON is selected, the Length indicator at the bottom of the display lights up. The default length when ON is 0.65" (16.5 mm) - the width of a Panduit Modular Jack.
EXAMPLE To select a labe l length of 10.5": Length 1 Hold down Code and press Q Rotate once. Caps A A A A A LENGTH inch OFF Keep Code held down and continue Rotate Length pre ssing Q until ON is displayed. Caps A A A A A Relea se Code Rotate A A A A A Rotate Press A Auto Underline Frame A A A A Auto LENGTH inch 10.50 Repeat Legend File 5 Frame Length Press "1050". Caps Underline LENGTH inch 00.65 Repeat Legend 4 Auto Length .
SIZE FUNCTION The character size of the entire text can be adjus ted using the size function. Since the character s ize that can be used depends on the width of the tape, the following table shows the character sizes that can be used with each tape width. Tape width Sizes (in points) 1/4" (6 mm) 12, 9 3/8" (9 mm) 18, 12, 9 1/2" (12 mm) 24, 18, 12, 9 3/4" (18 mm) 36, 24, 18, 12, 9 The default s ize setting is AUTO.
•1/2” (12-mm)- or 3/4” (18-mm)-wide tape is installed and the text contains only capital letters •3/4” (18-mm)-wide tape is installed and the characters are not formatted (i.e.
To se le ct the 24 point size setting: 2 While still holding down tinue pressing Size 1 Code , conRotate until 24 is displayed. Caps 3 38 Release Code .
UNDERLINE FUNCTION You can add emphasis to your text by underlining it. The default underline setting is OFF. When the underline function is s et to ON, the Underline indicator on the right s ide of the display lights up. ☞ If a frame has been chosen while the ON underline setting is selected, the frame setting changes back to OFF and the text is underlined.
FRAME FUNCTION With the frame function, you can choose from various frames and highlights to make more decorative or emphasized text. The following frame settings are available: OFF DIAMOND ROUND SLANT DOT The default frame setting is OFF. When any setting other than OFF is selected, the Frame indicator on the right side of the display lights up. ☞ If the ON under line setting has been chosen when a frame is selected, the underline setting changes back to OFF and the text is framed.
EXAMPLE To select the DOT frame setting: 1 While holding down Code , press Rotate Frame 9 once , and Code keep held down. Caps A A A A A FRAME OFF Underline Frame Length Repeat Legend 2 While still holding down Code , conRotate Frame tinue pressing 9 until DOT is dis- played. Caps A Relea se Code A A A A Auto FRAME DOT Repeat Legend 3 Auto Underline Frame Length .
HORIZONTAL ALIGNMENT FUNCTION You can choose to align lines in the text in one of three ways. In addition, if the length function was used to set the length of the label, the text will align within the label according to the selected horizontal alignment setting.
MIRROR PRINTING FUNCTION With this function, you can print your text so that the characters can be read from the adhesive side of the tape. If mirror-printed labels are attached to glass or some other clear material, they can be read correctly from the opposite s ide. The default mirror printing setting is OFF. OFF ON To change the mirror printing setting: Mirror 1 While holding down and press Code U once, and keep Code held down to dis- play the current mirror printing setting.
PRINT KEY, COPIES & FEED FUNCTIONS After you have entered your text and chos en the desired format s ettings, you are ready to print the label. To print a label: Copies ● Press once. The message “COPIES 01/01” is displayed while the label is being Print printed. The label is fed out of the tape exit slot at the top end of the machine. To print copies of a label: Copies ● Hold down and press Code Print . The mes sage “COPIES 01” is displayed. Enter between 01 and 99 copies . File ● Press .
SERIALIZATION FUNCTION This function can be used to print many copies of the s ame text while increasing a certain value in the text after each label is printed. This type of automatic incrementation is very us eful when printing serial number labels , patch panel labels or other labels requiring ascending codes. To use the numbering function: 1 Hold down Code and press V . The message “SERIALIZE NUMERIC” Serialize appears in the dis play.
2 Hold down Code and press V Serialize . Rotate Caps A A A A A SERIALIZE... NUMERIC 4 Relea se Press Code File . 1 Rotate Caps A A A A A $ Press 0 A A A A A Size Underline Frame Length File 1 Rotate Caps A A A A A Auto INCREMENT BY 01 Serialization is displayed as Ω Ω. Rotate Underline Frame Length Repeat Legend 7 Auto END VALUE 04 Repeat Legend 0 Frame File Caps Press Underline Length 4 Rotate 6 Auto START VALUE 01 Repeat Legend 5 Frame .
ROTATE LEGEND FUNCTION The rotate legend function is used when a label mus t be oriented vertically yet read horizontally. A common need for this function is terminal block labeling. To enable the rotate legend function: 1 Hold down Code and press until “ON” appears in the display. Space Rotate ☞ When Rotate Legend is enabled, the largest font siz e available is 6 pt.
3 V and press Serialize until NUMERIC is displayed. Hold down Code Rotate Caps A A A A A SERIALIZE... NUMERIC Release 5 Press Code File . 1 Rotate Caps A A A A A Caps A A A A A Size 0 1 Underline Frame Length File . Rotate Caps A A A A A Auto INCREMENT BY 01 Serialization is displayed a s ΩΩ . Rotate Underline Frame Length Repeat Legend 8 Auto END VALUE 10 Repeat Legend Press Frame Length .
REPEAT LEGEND FUNCTION The repeat legend function is used to duplicate a legend over the length of a label. Using the combined functionality of rotated legend and repeat legend produces an excellent quality label for marking cables and wires prior to or after ins tallation. To enable the repeat legend function for marking wires or other curved surfaces: 1 Hold down Code and press 2 Hold down Code and press X until “ON” appears in the display. Repeat Legend until “ON” appears in the display.
Length 3 Hold down and press Code Q Rotate until ON is displayed. Release . Code Caps A A A A A Auto LENGTH inch ON Underline Frame Length Repeat Legend Size 4 Press 0 0 1 0 Rotate A File . Caps A A A A LENGTH inch 01.00 Size Press D 1 Underline Frame Length Repeat Legend 5 Auto Size 0 1 . Rotate A A A A A Auto Underline Caps 1:D 1 0 1 Repeat Legend Copies 6 50 Press Print .
LINE DRAWING FUNCTION The line function is used to separate legends for easier recognition. The line function has two vertical line positions (left and right edge) and three horizontal positions (label top, every line and label bottom). To enable/dis able the line function: 1 Hold down tions. Release ☞ Line and press either Code Code 3 Line or 5 to toggle between the line posi- when the desired line position is displayed. Can be combined with the length, serialization and symbol functions.
4 Press Size . 1 Rotate A A A A A Auto Underline Caps 1:1 _ Frame Length Repeat Legend 5 Hold down Code and press V Serialize Release Code . Rotate . Caps A A A A A Auto SERIALIZE... NUMERIC Underline Frame Length Repeat Legend File 6 Press 0 . 0 Rotate Caps A A A A A START VALUE 00 Press Line 0 . Caps A A A A A Size 0 1 Underline Frame Length File . Rotate Caps Press Print A A A A A Auto INCREMENT BY 01 .
PAGE FUNCTION The page function is used to group multiple labels in a file. A file is a document consisting of up to 8 pages (labels). The page function is useful when labeling a group of items that have non-s erialized unique legends and must be grouped together. To enable the page function: Page 1 Hold down Code and press E to move to pages 1 thru 8. Release Code to enter text onto a page. ☞ Default position is page 1 of any label file.
@ 3 A Press Line 0 2 5 (page 1). Rotate A A A A A Auto Underline Caps 1:A 2 0 5 Frame Length Repeat Legend 4 Hold down Page and press Code E Rotate until LABEL PAGE 2 is displayed. Release . Code Caps A A A A A LABEL PAGE 2 Underline Frame Length Repeat Legend @ 5 A Press Auto Underline 0 2 7 . Rotate A A A A A Auto Underline Caps 1:A 2 0 7 _ Frame Length Repeat Legend 6 Hold down Code and press Page E Rotate A until LABEL PAGE 3 is displayed.
MEMORY FILE FUNCTIONS You can use the memory to store your most frequently us ed text files. The text remains in the memory, even after all characters are removed from the display using the clear function (see page 29). When a file is s tored, it is given a number to make recalling it eas ier. A maximum of 9 text files or about 300 characters can be s tored in the memory. A stored text file can contain a maximum of 99 characters.
To overwrite the stored file with the new one: File ● Pres s to delete the previously s tored file and store the new one under the selected number. ☞ To go back and choos e another file number without overwriting the text file, Clear press , and then select a different file number. BS RECALLING TEXT To recall a text file: File 1 Hold down 2 Press and press Code or . until RECALL flashes on the display. File 3 Press ☞ . The message “RECALL SELECT 1–9?” appears on the display.
☞ To quit the file delete function without deleting the text file, hold down File and press (or pres s just Size 4 Press the key ( 1 Code Clear BS ). Frame to 9 ) of the file number containing the text that you wish to delete. The text stored under the selected file number is shown. ☞ To s ee other parts of the selected text file, press or To display the text stored under other file numbers, pres s . Home or End , or the key of a different file number.
To recall the te xt from file number 4: File 1 Hold down Code and press . Rotate A A A A A Auto FILE Screen 104? ?? STORE Press until RECALL flashes on Rotate A the display. Frame Length Repeat Legend 2 Underline A A A A Auto FILE RECALL Underline Frame Length Repeat Legend File 3 Press . Rotate Caps A A A RECALL SELECT A A Auto Underline 1-9? Frame Length Repeat Legend $ 4 Press 4 .
To delete the te xt stored under file number 8: File 1 Hold down Code and press . Rotate A A A A A Auto F I L EScreen 104? ?? STORE Press until CLEAR flashes on the Rotate A display. Frame Length Repeat Legend 2 Underline A A A A Auto FILE CLEAR Underline Frame Length Repeat Legend File 3 Press . Rotate Caps A A A CLEAR SELECT A A Underline 1-9? Press 8 .
BARCODE FUNCTION The barcode function enables barcodes to be printed as part of labels. Four different parameters enable you to create custom barcodes . Parameter Settings PROTOCOL CODE 39 WIDTH (barcode width) LARGE, SMALL HUMAN READABLE (numbers printed below barcode) ON, OFF CHECK DIG. (check digit) OFF, ON The default settings are CODE 39 PROTOCOL, LARGE WIDTH , HUMAN READABLE set to ON, and CHECK DIG. set to OFF.
N and press . Barcode 2 Type in the new barcode data or edit the old data. To change the barcode parameter settings: 1 Press ☞ Home . To return to the barcode data display without changing any parameter settings, Clear press BS . 2 Press or 3 Press 4 Repeat steps 2 and 3until all parameters are s et as you wish. 5 Press Home or until the parameter that you wish to change appears. End until the desired setting is displayed. File .
To delete the barcode from your text: 1 Press , , Home or until the cursor is positioned either below the right End half of the barcode mark or immediately to the right of the entire barcode mark. Clear 2 Press 3 Press BS . The message “OK TO CLEAR? File 62 . ”.
EXAMPLE To add a barcode to the label: 1 Hold down Code and press N . Barcode Rotate A A A A A Auto CODE 39 ** Underline Frame Length Repeat Legend 2 Press Home . Rotate A A A A A Auto WIDTH SMALL Underline Frame Length Repeat Legend 3 Press until the CHECK DIG. Rotate parameter is displayed. A A A A A Auto CHECK DIG. OFF 4 Press or End until ON is disRotate playe d. Frame Length Repeat Legend Home Underline A A A A A Auto CHECK DIG.
@ Size 6 Press 1 , 2 , Line 3 $ , 4 , then Rotate Line 5 Press A A A A Auto CODE 39 *1 2 3 4 5 F * Underline Frame Length Repeat Legend File 7 A . .
TROUBLESHOOTING Problem Remedy 1. The printer is asking for “LABEL CODE”. • Enter LABEL CODE printed on tape cassette. 2. The dis play stays blank after you have turned on the machine. • Check that the correct AC adapter (LS7-ACS) is being used and that it is connected correctly. • If you are using alkaline batteries, check that they are correctly inserted. • If the batteries are low, replace them with new ones. 3. The machine does not print or the printed characters are blurred.
ERROR MESSAGE LIST Error Message 1 BAR CODE / LABEL Cause Remedy • This message appears if a barcode has already been added to the label when you hold down N Code • Limit the number of barcodes in the text to one. and pres s . Barcode 1 SERIALIZE LIMIT! • This message appears if a serialization has already been added to the label when you hold down press V Code • Limit the number of serializations in the text to one. and .
Error Message BUFFER EMPTY! Cause Remedy • This message appears if you try to print, but no text has been entered. • Enter text before printing. • This message appears if you try to store a text file in the memory, but no text has been entered in the display. • Enter text before storing. BUFFER FULL! • This message appears if you try to enter a character, symbol, barcode, return or space after 99 characters have already been entered. • Delete some existing text s o that more can be entered.
Error Message FUNCTION NOT ALLOWED! Cause Remedy • This message appears if Size, Frame or Barcode is set when Rotate function is being selected. • Delete Rotate function. • This mess age appears if Size is set when Repeat Legend function is being s elected. • Delete Repeat Legend function. INVALID VALUE • This message appears if you input the wrong value for the function s elected. • Re-input valid value.
Error Message Cause Remedy SET LENGTH! • This message appears if length has not been set when Rotate and Repeat Legend are selected. • Set length between 0.25" and 11.80" (6.4 and 299.7 mm). SYSTEM ERROR! • This message appears if there is a problem with the machine’s software. • Contact Technical Support at 866-871-4571 (outside the US, refer to page 70 for contact information). TEXT TOO HIGH! • This message appears if the size of the text is larger than the width of the installed tape.
SPECIFICATIONS HARDWARE Input device: Keyboard with 52 keys (including the power key) LCD: 12 characters × 2 lines (7 × 5 dots/character) 17 indicators Print tape: LS7 Tape Four widths available: 1/4” (6 mm) 3/8” (9 mm) 1/2” (12 mm) 3/4” (18 mm) Power supply: Six AA (AM3, LR6) alkaline batteries or optional AC adapter (LS7-ACS) Auto power-off if no key is pressed for 5 minutes Print head: 128 dot/180 dpi Dimensions: 4 3/4” (121 mm) (W) × 7 31/64” (190 mm) (D) × 2 51/64” (71 mm) (H) Weight: 1.
