User Manual

ManualsBrandsPANDUIT ManualsRaceway CouplerPANDUIT PN616C Floor Raceway Coupler

For Technical Support: www.panduit.com

INSTALLATION INSTRUCTIONS

฀©฀Panduit฀Corp.฀2022

PN616C

The mounting hardware used to secure

the raceway shall be appropriate for the

mounting surface.

Screws provided with raceway are

intended for installation on a concrete

surface.

NOTES:

• An adhesive strip may serve only as a positioning aid during the installation process. The raceway shall be secured by mechanical

fastening means.

• Holes for mounting raceway and associated fittings should be predrilled into infrastructure prior to the installation of the mounting

hardware.

• A 5/32" concrete drill bit is needed for the provided concrete screws.

Above Floor Raceway 4-Channel Standard Product

Part Number(s): AFR4BC**%, AFR4RA**, AFR4TRT70**, AFR4JB2S**, AFR4EC**, AFR4CC**,

AFR4TBLG**, AFR4WTR**

14 12 10

0.111 0.13 0.164

Max Max Max Spec Max Spec Max Spec Max

40% 60% 40% 60% 40% 60%

OuterChannels(withscrewsinstalled) A 211510342334

InnerChannels B 241711352335

DataGradeCables

Cat6A

Fill

Cat6A(SD)

Fill

0.24

24AWG 24AWG

0.3

24AWG

Cat6

Fill

0.24

ElectricalCables

THN/THWN/T90

Fill

ULTempRiseTest

RacewayChannel SeeFig.

Page 1 of 15

Summary of content (15 pages)

PAGE 1
Above Floor Raceway 4-Channel Standard Product Part Number(s): AFR4BC**%, AFR4RA**, AFR4TRT70**, AFR4JB2S**, AFR4EC**, AFR4CC**, AFR4TBLG**, AFR4WTR** ฀©฀Panduit฀Corp.฀2022 INSTALLATION INSTRUCTIONS Raceway Channel Outer Channels (with screws installed) Inner Channels PN616C Data Grade Cables Electrical Cables 14 12 10 24 AWG 24 AWG 24 AWG Cat 6A Cat 6A (SD) THN/THWN/T90 Cat 6 0.111 0.13 0.164 0.3 0.24 0.24 Fill Fill Fill Fill Max Max Max Spec Max Spec Max Spec Max See Fig.
PAGE 2
INSTALLATION INSTRUCTIONS ฀©฀Panduit฀Corp.฀2022 PN616C BASE & COVER 1 2 2a Screw to be no closer than 0.3" to inside latching rib 3 0.3" Space approximately 24" 3" maximum COUPLER 1 2 2a Ensure coupler is fully engaged with cover 3 4 RIGHT ANGLE 2 1 3 4 5 For Technical Support: www.panduit.com where ** denotes a color code and % denotes a length in feet Page 2 of 15 Stagger base joint and cover coupling joint to strengthen assembly.
PAGE 3
INSTALLATION INSTRUCTIONS ฀©฀Panduit฀Corp.฀2022 PN616C TRANSITION TO T70 1 2 4 3 5 END CAP 1 1a Ensure end cap and cover are fully engaged as shown. 0.3" is maximum allowable distance base can extend beyond cover when installing cap. 0.3" 2 For Technical Support: www.panduit.
PAGE 4
฀©฀Panduit฀Corp.฀2022 INSTALLATION INSTRUCTIONS JUNCTION BOX 1 PN616C 1a Ensure end cap and coupler(s) connect to junction box cover as shown [8 places] Note: Junction Box can be assembled between two raceway paths with the use of two coupler fittings. End cap installation shown as reference. 3 2 1" (25.4 mm) 3/4" (19.05 mm) Rectangular Breakout Rectangular Breakout 1/2" (12.7 mm) For Technical Support: www.panduit.
PAGE 5
฀©฀Panduit฀Corp.฀2022 INSTALLATION INSTRUCTIONS PN616C BREAKOUTS FOR CONDUIT APPLICATIONS POWER/DATA APPLICATION DATA APPLICATION 5 6 For Technical Support: www.panduit.
PAGE 6
INSTALLATION INSTRUCTIONS ฀©฀Panduit฀Corp.฀2022 PN616C WALL TRANSITION GREENFIELD APPLICATIONS - NEW CONSTRUCTION 2 1 1/2” 3 5/8” Stud Stud 1/2"drywall application 5/8"drywall application Determine if you will use 1/2" or 5/8" drywall. Orient standoff as shown for desired application. **Only use standoff for Greenfield applications** If installing into existing infrastructure, continue to Brownfield application instructions.
PAGE 7
฀©฀Panduit฀Corp.฀2022 INSTALLATION INSTRUCTIONS PN616C TABLE LEG INSTALLATION BETWEEN 2 RACEWAY CHANNELS 2 1 SUR FAC EN ONME 6 8YL FT4 03 Made inUSA PV C MEASURE TABLE HEIGHT TALLIC R ACE WA Y 600V MAX T O• P Measure the height from the floor to the underside of the table. Raceway Channel should be 3-1/4” Cover between 3-1/2" to 4" shorter than the meaCenter of table leg transition fitting will sit approximately 3-1/4" from the edge of the raceway cover. sured height.
PAGE 8
INSTALLATION INSTRUCTIONS ฀©฀Panduit฀Corp.฀2022 PN616C #10-32 Hex Nuts 3 4 Mounting Bracket Top Hole of Channel Top of Channel #10-32 x 1" Screws Secure mounting bracket to top of channel using provided hardware. Use the top hole of the channel for assembly. Do not fully tighten the mounting bracket at this time. 5 Ensure couplers connect to bottom transition boots as shown. [4 Places] 5A 6 For Technical Support: www.panduit.
PAGE 9
฀©฀Panduit฀Corp.฀2022 INSTALLATION INSTRUCTIONS 7 PN616C 8 #8-32 x 3/4" Wood Screws [4 Places] Capture Ledge Bottom Edge of Channel Transition Boot Set bottom edge of channel on capture ledge of installed transition boot. Connect second transition boot to the first. 9 Ensure channel is level.Secure mounting bracket to underside of table using provided hardware. Fully tighten mounting bracket screws to secure channel in place.
PAGE 11
฀©฀Panduit฀Corp.฀2022 INSTALLATION INSTRUCTIONS INSTALLATION AS STAND ALONE OR WITH SINGLE SIDE RACEWAY CHANNEL NOTE: For single side raceway application; above floor raceway should be mounted prior to table leg installation. Center of table leg will sit approximately 3-1/4" from the edge of the raceway cover. Route cables prior to installing the raceway cover. NOTE: Desired hole in table should be offset from table leg center to accommodate proper mounting of table leg. For Technical Support: www.
PAGE 12
฀©฀Panduit฀Corp.฀2022 INSTALLATION INSTRUCTIONS PN616C 2 1 03 Made inUSA PVC MEASURE TABLE HEIGHT Measure the height from the floor to the underside of the table. Channel should be between 3-1/2" and 4" shorter than measured height. If necessary, cut channel from bottom edge to accommodate. NOTE: Desired hole in table should be offset from table leg center to accommodate proper mounting of table leg.
PAGE 13
INSTALLATION INSTRUCTIONS ฀©฀Panduit฀Corp.฀2022 4 #10-32 Hex Nuts PN616C 5 #10-32 x 1" Screws Secure mounting brackets to top and bottom of channel using provided hardware. Use the holes closest to the ends of the channel for assembly. Do not fully tighten the mounting bracket at this time. Pre-drill holes in infrastructure if necessary. Secure bottom mounting bracket to floor with proper hardware.
PAGE 14
INSTALLATION INSTRUCTIONS ฀©฀Panduit฀Corp.฀2022 9 8 Capture Ledge PN616C Stepped Flange Covers [2 Places] Bottom Transition Boots Bottom Edge of Channel Assemble bottom transition boots together. Transition boot latches (shown in step 7) will mount to stepped flanges of the mounting brackets. Place bottom of channel on top of capture ledge of transition boots. Route cables prior to installing covers. Covers are tamper proof and are not intended for easy removal.
PAGE 15
INSTALLATION INSTRUCTIONS ฀©฀Panduit฀Corp.฀2022 PN616C 11 E-mail: techsupport@panduit.com For Instructions in Local Languages and Technical Support: www.panduit.com www.panduit.