Cut Sheet

www.panduit.com
SPECIFICATION SHEET
Material: Rigid PVC
Flammability: UL94V-0; FT4
Voltage rating: UL-5A 600VAC; CSA C22.2 No. 62.1-03 600V
Approvals: UL Listed 95425 (raceway); UL Listed E116129 (fittings)
NEC: Article 388
Color: Off White (IW), Electrical Ivory (EI), White (WH). International Gray (IG) avail-
able in 8' lengths only.
CSI spec form: LP-CSISPEC-T70-1
key features and benefits
applications
technical information
specifications
T-70 non-metallic multi-channel capable surface raceway shall be
used to route, protect, and conceal data, voice, video, fiber optic
and power cabling. The raceway shall be listed as suitable for use
in applications up to 600 volts between conductors by Underwriters
Laboratories, Inc. per standard 5A, and by Canadian Standards
Association, Inc. per 22.2 no. 62.1-03, when screw secured and
installed per instructions. A full complement of fittings with a 1”
minimum bend radius compliant with TIA/EIA-568-B, must be
available as well as device brackets and internal junction boxes to
install a variety of communication and electrical devices. Divider
walls must be available to form separate channels in the
multi-channel raceway. “Snap-on” faceplates for data and power
terminations shall be available. An offset box shall be available, with
versions for Panduit “snap-on” as well as “screw mount”
faceplates, for mounting the power receptacle outside of the raceway
channel. T-70 raceway will be manufactured from impact-resistant
material with flammability rating of V-0. T-70 raceway must be tam-
per resistant yet, also allow access for moves, adds and changes.
T-70 raceway finish shall be pure color and will resist scratches and
dents and will not peel or corrode. T-70 raceway shall be available in
four standard colors and shall be optimized for use with the Panduit
®
Pan-Net
®
Communication System.
1” bend radius Cables in the raceway will satisfy the minimum 1” bend radius requirement,
control fittings preventing the potential degradation of cable performance; meets TIA/EIA
standard and many warranty requirements
Snap-on faceplates Faceplates snap directly onto the raceway base; cabling can be quickly accessed
by removing only the faceplate, which requires less labor and lowers the cost of
maintenance
Channel has a Accepts any manufacturer’s NEMA standard snap-on or screw-on power or
70mm opening communication faceplates
Highly tamper Very difficult for untrained personnel to enter the raceway or remove faceplates;
resistant provides maximum security for communication cabling and maximum safety for
power cabling
Non-metallic Lightweight reduces installer fatigue; solid color throughout profile will not chip
construction peel, rust, corrode, or scratch; easy to cut reducing the need for special cutting
devices; high impact resistance; durable
Designer profile Aesthetically pleasing and matches a wide variety of decors
Available in four Matches a variety of colors for various applications
standard colors
Pan-Way
®
T-70 Non-Metallic Surface Raceway is a
multi-channel channel raceway which provides
solutions for routing low voltage, fiber optic and/or
power cabling along perimeter walls. T-70 raceway
can mount NEMA standard screw-on faceplates or
superior Pan-Way
®
Snap-On Faceplates directly to
the channel. T-70 features the Workstation Outlet
Center
™
Offset Box, which provides an offset
solution to maximize channel capacity and
outlet density.
T-70 Raceway Fittings
and Accessories
Base coupling: T70BCIW-X
Cover coupling: T70CCIW-X
Outside corner
fitting: T70OCIW
Inside corner
fitting: T70ICIW
Right angle fitting: T70RAIW
End cap fitting: T70ECIW
Entrance end
fitting: T70EEIW
Tee fitting: T70TIW
Insert for tee fitting: T70TD
Transition fitting
base/cover: T70TRIW
Transition fitting
cover only: T70TRCIW
Wire retainer: T70WR-X
Device bracket: T70DB-X
Standard faceplate
bracket: T70SDB-X
Three sided
hanging box: T70HB3-X
GFCI three sided
hanging box: T70HB3GFCI-X
Hanging box: T70HB-X
Workstation
Outlet Center
™
Offset Box: T70WCIW
Workstation
Outlet Center
™
Offset Box: T70WC2IW
Backfeed fitting: T70BFIW
Backfeed fitting
insert: T70BFI
Fiberspool bracket
(two halves): T70FSB
For standard colors other than IW (Off White),
replace IW in part number with EI (Electrical
Ivory), WH (White) or IG (International Gray). IG
(International Gray) is available in 8' lengths only.
Pan-Way
®
T-70 Raceway
Raceway Base
6 feet: T70BIW6
8 feet: T70BIW8
10 feet: T70BIW10
Raceway Cover
6 feet: T70CIW6
8 feet: T70CIW8
10 feet: T70CIW10
Divider Wall
6 feet: T70DW6
8 feet: T70DW8
10 feet: T70DW1
Pan-Way
®
T-70 Surface Raceway System